Products 1-48 of 110
Show
SparkFun Logic Level Converter - Bi-Directional
Price: $4.76
View
Availability: Stocked
Sparkfun Item #: BOB-12009 -

"If you’ve ever tried to connect a 3.3V device to a 5V system, you know what a challenge it can be. The SparkFun bi-directional logic level converter is a small device that safely steps down 5V signals to 3.3V AND steps up 3.3V to 5V at the same time. This level converter also works with 2.8V and 1.8V devices. What really separates this Logic level converter from our previous versions is that you can successfully set your high and low voltages and step up and down between them safely on...

GPS Shield With Antenna
Price: $55.53
View
Availability: Stocked
Elecrow Item #: EL-MCS01107S -

The GPS Shield is base on the ublox\'s NEO-6M receiver module , and the footprints is compatible with Arduino/MEGA boards. The regular GPS pins (RX, TX) can be connected to D0-D7 of Arduino. Support software SerialPort and Micro SD card interface. It\'s very easy to use. You just need read SerialPort and then you will get the GPS data. The GPS Shield module interfaces to the customer and application via one serial port, which uses CMOS voltage levels. support 3.3V / 5V IO operating. That\'s...

SparkFun USB to Serial Breakout - FT232RL
Price: $24.15
View
Availability: Stocked
Sparkfun Item #: BOB-12731 -

"This is the SparkFun USB to Serial Breakout for the FT232RL, a small board with a built in USB to serial UART interface. This little breakout is built around the FT232RL IC from FTDI, with an internal oscillator, EEPROM, and a 28-pin SSOP package this is a serious little chip. With this version, we’ve corrected a few issues found with the board. These changes include fixes to the VCCIO, a change from the mini USB to micro USB connector, and a few footprint modifications. Other than...

SparkFun microSD Transflash Breakout
Price: $6.58
View
Availability: Stocked
Sparkfun Item #: BOB-00544 -

"Breakout board for the microSD socket that is not much bigger than your fingernail. Compatible with the SPI interface found on any SD card, this tiny form factor was created for cell phone storage and is perfect for your next MP3 project! Board comes fully assembled and tested. The bare socket is available. Documents: Schematic Eagle Files Datasheet MMC to Serial Adapter Example MMC Interface Code Adding SD to a Router - Thanks Jake! Eagle Layout as well! mbed Example GitHub " ...

SparkFun USB Mini-B Breakout
Price: $3.25
View
Availability: Stocked
Sparkfun Item #: BOB-09966 -

"This new version now has all 5 pins broken out on the connector. We have no idea what USB device you are hooking up to, but if you need to add a miniUSB/USB Mini-B connector to your breadboard - here it is. Also good for an un-regulated, non-limited 5V supply up to 100mA. Documents: Eagle Files GitHub " ...

SparkFun UV Sensor Breakout - ML8511
Price: $20.59
View
Availability: Stocked-NoBackOrder
Sparkfun Item #: SEN-12705 -

"The ML8511 breakout is an easy to use ultraviolet light sensor. The MP8511 UV (ultraviolet) Sensor works by outputing an analog signal in relation to the amount of UV light that’s detected. This breakout can be very handy in creating devices that warn the user of sunburn or detect the UV index as it relates to weather conditions. This sensor detects 280-390nm light most effectively. This is categorized as part of the UVB (burning rays) spectrum and most of the UVA (tanning rays)...

SparkFun Real Time Clock Module
Price: $24.92
View
Availability: Stocked
Sparkfun Item #: BOB-12708 -

"This is the SparkFun Real Time Clock (RTC) Module, this little breakout that uses the DS1307 to keep track of the current year, month, day as well as the current time. The module comes fully assembled and includes a small CR1225 Lithium coin cell battery that will run the RTC for a minimum of 9 years (17 years typical) without an external 5V power supply. The DS1307 RTC is accessed via the I2C protocol. We’ve written a test-bed to program the modules, this code should give you some...

Breakout Board for XBee Module
Price: $4.92
View
Availability: Stocked
Sparkfun Item #: BOB-08276 -

"This is a simple breakout board for the popular XBee product from Digi. This board breaks out all 20 pins of the XBee to a 0.1" standard spacing dual row header. The spacing between 0.1" headers is 0.5" making it breadboard DIP friendly. We highly recommend using the female sockets to avoid having to solder the XBee permanently to the breakout board. This is the PCB only. Please order the accompanying 2mm sockets (you’ll need 2!) and 0.1" headers below. Documents: Schematic Eagle...

SparkFun SOIC to DIP Adapter - 8-Pin
OOD!
Price: $4.76
View
Availability: Back Order
Sparkfun Item #: BOB-13655 -

"The SparkFun 8-Pin SOIC to DIP Adapter is a small PCB that lets you adapt SOIC packages into a DIP footprint. These tiny boards are useful for modding and upgrading devices that use 8-pin DIP ICs, when the upgraded IC is only available in a SOIC footprint. You can also use these adapters for prototyping by making SOIC packages compatible with solderless breadboards. This version of the SparkFun SOIC to DIP Adapter adapter comes as a small array of four boards. We did this because if...

SparkFun DeadOn RTC Breakout - DS3234
Price: $33.25
View
Availability: Stocked
Sparkfun Item #: BOB-10160 -

"Here is a real time clock based on the DS3234 Real Time Clock IC. The DS3234 is a low-cost, extremely accurate SPI bus real-time clock with an integrated temperature-compensated crystal oscillator and crystal. The RTC maintains seconds, minutes, hours, day, date, month, and year information. The date at the end of the month is automatically adjusted for months with fewer than 31 days, including corrections of leap year. The clock operates in either the 24-hour or 12-hour format with AM/PM...

GPS Receiver - GP-20U7 (56 Channel)
OOD!
Price: $26.23
View
Availability: Back Order
Sparkfun Item #: GPS-13740 -

"The GP-20U7 is a compact GPS receiver with a built-in high performances all-in-one GPS chipset. The GP-20U7 accurately provides position, velocity, and time readings as well possessing high sensitivity and tracking capabilities. Thanks to the low power consumption this receiver requires, the GP-20U7 is ideal for portable applications such as tablet PCs, smart phones, and other devices requiring positioning capability. This 56-channel GPS module, that supports a standard NMEA-0183 and uBlox 7...

Servo Shaft Coupler - Hitec Standard
OOD!
Price: $8.05
View
Availability: Back Order
Sparkfun Item #: ROB-12501 -

"These couplers allow you to connect a 1/4” shaft directly to your C1 Hitec servo spline. The set screw included with each shaft coupler works well with straight or d-shafts. These servo shaft couplers have a length of 0.5”, an outer diameter of 0.42”, and an inner diameter of 0.25”. Actobotics is a robotics building system based around extruded aluminum channels, gears, precision shafts, and ball bearings. Thanks to the two standardized hole patterns, nearly all...

Wheel Encoder Kit
OOD!
Price: $20.90
View
Availability: Back Order
Sparkfun Item #: ROB-12629 -

"This is the Wheel Encoder Kit from DAGU, a simple add-on to any wheeled robot that can help measure the speed or distance the chassis travels. Each wheel encoder kit consists of two neodymium 8-pole magnets with rubber hubs and two hall-effect sensors terminated with 150mm cables and 3-pin female servo headers. These wheel encoders require a supply voltage of 3-24V with a supply current of 4mA. Features: Supply Voltage: 3-24V Supply Current: 4mA per sensor Output Voltage: 26V Max Output...

SparkFun Venus GPS with SMA Connector
Price: $83.25
View
Availability: Stocked
Sparkfun Item #: GPS-11058 -

"This is the latest version of our Venus GPS board; the smallest, most powerful, and most versatile GPS receiver we carry. It’s based on the Venus638FLPx, the successor to the Venus634LPx. The Venus638FLPx outputs standard NMEA-0183 or SkyTraq Binary sentences at a default rate of 9600bps (adjustable to 115200bps), with update rates up to 20Hz! The Venus638FLPx also allows for limited on-chip logging (check out the firmware below), as well as external logging using a SPI flash memory...

SparkFun SSOP to DIP Adapter - 28-Pin
Price: $6.58
View
Availability: Stocked
Sparkfun Item #: BOB-00500 -

"8, 16, 20, and 28-Pin SSOP to DIP break out boards. The footprint was rotated to accommodate different width SSOP devices and can be used with any pin count up to 28 pins. Designed to be used with 0.65mm pitch devices but can also be used with 0.025" pitch devices (comes out to ~0.635mm). We’ve made these 0.635mm devices fit just fine. Can be used with packages that have a lead span of .230" up to .350". Breaks out SSOP pins to standard .6" (600mil) and .3" (300mil) DIP width to be used...

SparkFun Altitude/Pressure Sensor Breakout - MPL3115A2
OOD!
Price: $24.13
View
Availability: Back Order
Sparkfun Item #: SEN-11084 -

"Life has its ups and downs, so why not measure them? The MPL3115A2 is a MEMS pressure sensor that provides Altitude data to within 30cm (with oversampling enabled). The sensor outputs are digitized by a high resolution 24-bit ADC and transmitted over I2C, meaning it’s easy to interface with most controllers. Pressure output can be resolved with output in fractions of a Pascal, and Altitude can be resolved in fractions of a meter. The device also provides 12-bit temperature measurements...

SparkFun Rotary Switch Breakout
OOD!
Price: $3.15
View
Availability: Back Order
Sparkfun Item #: BOB-13098 -

"This is the SparkFun Rotary Switch Breakout, a very simple board designed to easily provide you access to each pin on our 10-position rotary switches. This breakout allows you to easily add a rotary switch to your next project without having to worry about attaching its unique footprint to a custom board or solderless breadboard. All you need to do is solder the 10-position rotary switch into the breakout (using the silkscreen on the board as a guide) and each pin will become available for...

SparkFun SOIC to DIP Adapter - 28-Pin
OOD!
Price: $6.38
View
Availability: Back Order
Sparkfun Item #: BOB-00496 -

Low-cost basic SOIC break out boards. These are custom PCB boards that interface standard SOIC devices to standard .1" headers.Pad layout fits all standard SOIC devices. 28-SOIC Standard .6" spacing between pins. Will fit directly into a standard width (600 mil) DIP socket. For wide ICs (memories, drivers, 74s, etc). 40 Pin break-away headers are perfect for use with these custom PCBs. Machine pin headers may be a better option for IC sockets.Dimensions: 0.7x1.50"Documents: Schematic Eagle...

WiiChuck Adapter
OOD!
Price: $3.15
View
Availability: Back Order
Sparkfun Item #: DEV-09281 -

"The WiiChuck Adapter is a small PCB that is designed to be inserted into the connector of a Nintendo Wii Nunchuck to provide access to all 4 wires of the remote. The power, ground and two-wire interface of the Nunchuck are all broken out to a 4-pin 0.1" pitch header. The Wii Nunchuck is loaded with features – a 2-axis joystick, two buttons and a 3 axis ±2g accelerometer – and any device capable of I2C can communicate with it! The WiiChuck allows you to interface with the...

SparkFun Level Shifting microSD Breakout
OOD!
Price: $7.99
View
Availability: Back Order
Sparkfun Item #: DEV-13743 -

"The SparkFun Level Shifting microSD Breakout is quite similar to the SparkFun microSD Transflash Breakout, but with the included level shifting hardware, this board allows you to utilize a microSD card at Arduino’s SD library’s top speed on a 5V system. With this small breakout board, that is not much bigger than your fingernail, adding mass storage to your project will never be easier. With the additional feature of being 3.0V to 5.0V tolerant for ease of use, discrete level...

SparkFun MEMS Microphone Breakout - INMP401 (ADMP401)
OOD!
Price: $16.06
View
Availability: Back Order
Sparkfun Item #: BOB-09868 -

"This tiny breakout board features the ADMP401 MEMs microphone. One of the key advantages to this breakout and microphone is the bottom ported input. This means the microphone’s input can fit flush against the enclosure of your project. Plus you will not have to deal with trying to solder the microphone’s wacky footprint. Wootness! The amplifier on the breakout has a gain of 67 and more than meets the bandwidth requirements of the mic. The amplifier’s AUD output will float at...

SparkFun Rotary Switch Potentiometer Breakout
Price: $3.16
View
Availability: Stocked
Sparkfun Item #: BOB-13099 -

"The SparkFun Rotary Switch Potentiometer Breakout is a small board the allows you to add resistors to a 10-position rotary switch, turning it into a potentiometer with 10 discrete steps. Multiple applications require potentiometers that are hard to find due to specific resistance values or custom tapers, the Rotary Switch Potentiometer board allows you to populate your own resistors to help match situations where ordinary parts aren’t available or suitable. Specific resistors can also...

SparkFun RFM69 Breakout (915MHz)
OOD!
Price: $16.06
View
Availability: Back Order
Sparkfun Item #: WRL-12775 -

"This is the SparkFun RFM69 Breakout, a small piece of tech that breaks out all the pins available on the RFM69HCW module as well as making the transceiver easy to use. The RFM69HCW is an inexpensive and versatile radio module that operates in the unlicensed ISM (Industry, Science and Medicine) radio band. It’s perfect for building inexpensive short-range wireless networks of sensors and actuators for home automation, citizen science and more. This RFM69HCW operates on the 915MHz...

SparkFun SSOP to DIP Adapter - 16-Pin
OOD!
Price: $4.76
View
Availability: Back Order
Sparkfun Item #: BOB-00498 -

"8, 16, 20, and 28-Pin SSOP to DIP break out boards. The footprint was rotated to accommodate different width SSOP devices and can be used with any pin count up to 28 pins. Designed to be used with 0.65mm pitch devices but can also be used with 0.025" pitch devices (comes out to ~0.635mm). We’ve made these 0.635mm devices fit just fine. Can be used with packages from 0.200" (5mm) up to 0.450" (11.4mm) in width. Breaks out SSOP pins to standard .6" (600mil) and .3" (300mil) DIP width to...

SparkFun Thermocouple Breakout - MAX31855K
Price: $24.67
View
Availability: Stocked
Sparkfun Item #: SEN-13266 -

"The SparkFun MAX31855K Thermocouple Breakout is a simple 14-bit resolution, SPI-compatible, serial interface thermocouple digitizer that makes reading a wide range of temperatures possible. A thermocouple works by taking two wires made of dissimilar metals, connecting them at the two ends, and making a temperature gradient between one end and the other (a ‘hot’ end and a ‘cold’ one). Once this is achieved, a voltage potential is formed and current flows. The SparkFun...

SparkFun SSOP to DIP Adapter - 16-Pin
OOD!
Price: $4.76
View
Availability: Back Order
Sparkfun Item #: BOB-13994 -

"The SparkFun 16-Pin SSOP to DIP Adapter is a small PCB that lets you adapt SSOP packages into a DIP footprint. These small boards are useful for modding and upgrading devices that use 14- and 16-pin DIP ICs, when the upgraded IC is only available in an SSOP footprint. You can also use these adapters for prototyping by making SSOP packages compatible with solderless breadboards. This version of the SparkFun SSOP to DIP Adapter comes as a duo of boards. We did this because if you’re...

GPS Receiver - EM-506 (48 Channel)
OOD!
Price: $64.56
View
Availability: Back Order
Sparkfun Item #: GPS-12751 -

"The EM-506 GPS receiver from USGlobalSat based on the spectacular SiRF StarIII chipset. This complete module is built upon the same technology as the ET-301, but includes on-board voltage regulation, LED status indicator, battery backed RAM, and a built-in patch antenna! 6-pin interface cable included. This EM-506 GPS module is powered by SiRF Star IV, it can provide you with superior sensitivity and performance even in urban canyon and dense foliage environment. With SiRF CGEE (Client...

SparkFun Cellular Shield - MG2639
Price: $116.58
View
Availability: Stocked-NoBackOrder
Sparkfun Item #: CEL-13120 -

"The MG2639 SparkFun Cellular Shield is a perfect addition to any Arduino project that requires connectivity when there’s no WiFi or Ethernet access nearby. The ZTE MG2639 module, which this shield is built around, supports SMS, TCP, UDP, and can even be used to make or receive phone calls! That means you can send and receive text messages, or use it to remotely connect your Arduino to the Internet. To top it off, it has an integrated GPS receiver, to help it from getting lost. All the...

SparkFun LED Driver Breakout - TLC5940 (16 Channel)
OOD!
Price: $20.90
View
Availability: Back Order
Sparkfun Item #: BOB-10616 -

"The TLC5940 is a 16 channel PWM unit with 12 bit duty cycle control (0-4095), 6 bit current limit control (0-63), and a daisy chainable serial interface. This breakout board is a good way to take full advantage of this useful IC. All 16 PWM channels are broken out to standard 0.1" headers, which run alongside convenient voltage and ground rails. Also, because the TLC5940 can be daisy-chained, the breakout is designed to support that feature. On the left-hand side of the board all serial...

SparkFun MiniGen - Pro Mini Signal Generator Shield
OOD!
Price: $48.34
View
Availability: Back Order
Sparkfun Item #: BOB-11420 -

"This is the SparkFun MiniGen Signal Generator, a small shield for the Arduino Pro Mini that is capable of generating sine, square, or triangle waves at up to 3MHz, and approximately 1Vp-p. Though the MiniGen is technically a shield it can, in fact, operate as a stand-alone board capable of the the same functionality as it would if it were placed on top of a Pro Mini. The MiniGen offers two out put sources for you to utilize: a 2-pin 0.1" spaced header and a u.FL connector. The output is at a...

SparkFun SOIC to DIP Adapter - 20-Pin
Price: $6.59
View
Availability: Stocked
Sparkfun Item #: BOB-00495 -

"This is a low-cost, basic SOIC breakout boards. This custom PCB will interface a standard SOIC package IC to 0.1" headers, which are easier to work with and integrate well with breadboards. There is DIP-standard 0.6" spacing between the two rows of pins. 40 Pin break-away headers are perfect for use with these custom PCBs. Machine pin headers may be a better option for IC sockets. Dimensions: 0.7x1.1" Documents: Schematic Eagle Files GitHub (Design Files) " ...

SparkFun RFID Reader Breakout
Price: $3.25
View
Availability: Stocked
Sparkfun Item #: SEN-13030 -

"This is a simple breakout board for our RFID readers. The SparkFun RFID Reader Breakout converts the 2mm pins to bread board friendly 0.1" headers. With this ability the ID-3LA, ID-12LA, and the ID-20LA you can solder the reader directly to the breakout board or use the 2mm sockets. This breakout board’s edges actually fit flush within the under side the ID-12LA. The board also works with the ID-20LA, but is smaller than the edges. As stated before each pin of the RFID reader has been...

SparkFun Full-Bridge Motor Driver Breakout - L298N
OOD!
Price: $4.76
View
Availability: Back Order
Sparkfun Item #: BOB-09540 -

"This is a breakout board for the L298N full-bridge dual motor driver; which comes in a staggered, Multiwatt package. All pins of the L298N are broken out to a 15-pin 0.1" pitch header. Two mounting holes are also provided. Dimensions: Board: 1.6x0.85 inches Documents: Schematic Eagle Files Datasheet (L298N) GitHub (Design Files) " ...

SparkFun Micro OLED Breakout
Price: $24.92
View
Availability: Stocked
Sparkfun Item #: LCD-13003 -

"The SparkFun Micro OLED Breakout Board breaks out a small monochrome, blue-on-black OLED. It’s “micro”, but it still packs a punch – the OLED display is crisp, and you can fit a deceivingly large amount of graphics on there. This breakout is perfect for adding graphics to your next Arduino project, displaying diagnostic information without resorting to serial output, and teaching a little game theory while creating a fun, Arduino-based video game. Most important of...

SparkFun Electric Imp Breakout
Price: $21.58
View
Availability: Stocked
Sparkfun Item #: BOB-12886 -

"If you aren’t familiar with the Electric Imp, it essentially provides an easy, integrated way to connect almost any hardware device both to other devices and to internet services. The SparkFun Electric Imp Breakout Board allows you to explore the capabilities of the Imp by providing standard 0.1" headers to solder to as well as the necessary CryptAuthEE IC to identify your prototype to the Imp Cloud service! This is just the development board, so you’ll need to buy the Imp...

USB Relay Controller with 6-Channel I/O
Price: $96.76
View
Availability: Out of Stock
Sparkfun Item #: DEV-09669 -

"This USB Relay Controller / Data Acquisition Module, from Cana Kit, allows computer controlled switching of external devices as well as full bi-directional communication with the external world (ideal for Data Acquisition applications) using the USB port of your computer. The controller is very flexible and can be used in many custom applications including weather stations as well as temperature monitoring, logging and control as it can be easily connected to temperature and other types of...

SparkFun Energy Harvester Breakout - LTC3588
OOD!
Price: $48.34
View
Availability: Back Order
Sparkfun Item #: BOB-09946 -

"This breakout board uses the LTC3588 Piezoelectric Energy Harvester from Linear Technologies. This board can be used not only for harvesting piezoelectric energy, but solar energy as well. There is a bridge rectified input for piezo elements (PZ1 and PZ2) and a direct input (VIN) for DC sources. Both are clamped to 20V. In addition, the board can simply be used as a standalone nanopower buck regulator. An ultralow quiescent current undervoltage lockout (UVLO) mode with a wide hysteresis...

SparkFun RJ45 MagJack Breakout
OOD!
Price: $7.99
View
Availability: Back Order
Sparkfun Item #: BOB-13021 -

"This is the SparkFun RJ45 MagJack Breakout, a simple board that will provide you with a way to put an ethernet port into your breadboard. The SparkFun RJ45 MagJack Breakout is the same one found in our very own mbed Starter Kit and breaks out each pin from the ethernet jack. This rev of the breakout is equipped with the RJ45 MagJack connector already soldered to the board which mean you no longer need to solder the connector to the board yourself or worrying about buying them separately! The...

SparkFun Rotary Encoder Breakout - Illuminated (RG/RGB)
OOD!
Price: $4.76
View
Availability: Back Order
Sparkfun Item #: BOB-11722 -

"This is a clever little breakout board for both the RGB and R/G illuminated rotary encoders. On one side, it breaks out all of the RGB pins to standard, breadboard friendly, 0.1" headers. Turn it over and it has a footprint for the R/G version! Simply solder an encoder down to the board and you’re ready to add illuminated input to your next project. Documents: Schematic Eagle Files GitHub " ...

SparkFun SD/MMC Card Breakout
OOD!
Price: $16.06
View
Availability: Back Order
Sparkfun Item #: BOB-12941 -

"With SD and MMC memory prices dropping, the time is right for mass storage and datalogging. This breakout board will allow you to breakout the SD/MMC socket to a standard .1" 10-pin header. Perfect for breadboarding and the likes. Board comes fully assembled and tested as shown. Dimensions: 1.3" x 1.5" Documents: Schematic Eagle Files Datasheet (SD/MMC Socket) GitHub (Design Files) " ...

Cherry MX Switch Breakout
Price: $3.25
View
Availability: Stocked
Sparkfun Item #: BOB-13773 -

"Cherry MX Keyswitches are top-of-the-line mechanical keyboard switches. They’re satisfyingly “clicky”, reliable up to tens-of-millions of key presses, and a standard in gaming and programming keyboards across the globe. With the SparkFun Cherry MX Switch Breakout we have made the switches more easily adaptable to breadboard or perfboard-based projects. The Cherry MX Switch Breakout is a perfect prototyping tool for projects ranging from a single-key user-input to...

Connector Horizontal SMD for EB-85A
OOD!
Price: $3.15
View
Availability: Back Order
Sparkfun Item #: GPS-08297 -

"Horizontal surface mount connector for the EB-85A/FV-M8 GPS receiver. Documents:EB-85A-Connector.pdf"

Ethernet Interface Board - ENC28J60
OOD!
Price: $56.49
View
Availability: Back Order
Sparkfun Item #: BOB-00765 -

"Small breakout board for the PIC Microchip ENC28J60. Contains all the necessary hardware to implement an Ethernet interface including the isolation transformer and LINK/STATUS LEDs. SPI interface makes this one of the easiest 10Base-T ICs yet! 3.3V with 8KB buffer. Dimensions: Overall : 1.18x0.95" (30x24mm) Space between rows : 0.8" Documents: Schematic Datasheet (ENC28J60) " ...

GPIB-USB Controller
Price: $282.46
View
Availability: Out of Stock
Sparkfun Item #: BOB-00549 -

"Use this unique device to download data and control GPIB bus enabled oscilloscopes, logic analyzers, function generators, power supplies, and any other GPIB instrument seamlessly through USB! Features: Drivers for Windows 98/ME/2000/XP/Vista/Win7, Mac OS-8/9/X, Linux Support for multiple devices Driver provides virtual serial port to send and receive data Powered by USB; no power supply needed No GPIB cable needed; controller plugs on to instrument All software configuration. No DIP...

GPS Active Antenna ( 5m Plug Series Connector)
OOD!
Price: $18.20
View
Availability: Back Order
Elecrow Item #: EL-WAG05010G -

GPS Active Antenna (3m Plug Series Connector)
OOD!
Price: $15.87
View
Availability: Back Order
Elecrow Item #: EL-WAG03010G -

This is a GPS Active Antenna which can make you received the GPS form indoor. Its cable is 3m. It can be used with our GPS Shield to make the GPS Shield can be used in the home or somewhere don\'t have GPS signal.SpecificationFrequency: 1575.42MHZVoltage: 3.0-5.0VSize: 3.9 x 5.0cmCable Length: 3m(Approx.)Water resistantIt contains a high performance GPS patch antenna and a high-tech low noise amplifier, providing excellent signal amplification and out-band-rejection for the receiverMounting:...

GPS Module - Venus638FLPx-L 20Hz (14 Channel)
Retail: $75.00
Price: $66.58
View
Availability: Stocked
Sparkfun Item #: GPS-10919 -

"Venus638FLPx is a high performance, low cost, single chip GPS module targeting mobile consumer and cellular handset applications. It offers very low power consumption, high sensitivity, and best in class signal acquisition and time-to-first-fix performance. Venus638FLPx contains all the necessary components of a complete GPS module, includes 1.2dB cascaded system NF RF front-end, GPS baseband signal processor, 0.5ppm TCXO, 32.768kHz RTC crystal, RTC LDO regulator, and passive components. It...

GPS Receiver - GP-735 (56 Channel)
OOD!
Price: $64.48
View
Availability: Back Order
Sparkfun Item #: GPS-13670 -

"The GP-735 is a slim, ultra-high performance, easy to use GPS smart antenna receiver. With -162dBm tracking sensitivity and only 29 second cold start time, the GP735 is a tiny, yet powerful, piece of tech. The slim design makes it ideal for applications where you don’t have a lot of space to work in. Really it’s quite small. This 56-channel GPS module, based on the uBlox 7th generation chipset, has an operating voltage of 3.3~5.5V, an antenna on board, and connects to your system...