Products 25-48 of 627
Show
Graphic LCD4884 Shield For Arduino
Price: $49.22
View
Availability: Out of Stock
Item #: DFR0092 -

Graphic LCD4884 Shield For Arduino Introduction This LCD4884 Shield provides 48x48 display. If your project need more information to display, this LCD shield can apparently meet your needs. It is able to display English, Chines, even images. It also integrates a 5 DOF joystick.  The shield has 6 Digital IO and 5 Analog IO.  Note:The Arduino in the image is NOT included. Specification Power Supply: 5V SPI Interface (using Arduino Digital Pin 2,3,4,5,6) One Reset button One 5 degree...

Gravity:DIGITAL IR Transmitter Module
Sale!
Price: $6.72
View
Availability: Back Order
Item #: DFR0095 -

An infrared transmitter is simply a Light Emitting Diode which generates IR light (invisible IR light)--light with a wavelength of between 1 mm and 750 nanometers, and some associated circuitry. In an infrared remote control, for example, pushing a button sends an electric signal to the LED, which converts the signal into a beam of infrared light. The receiving device detects the light with a photo diode and converts it to an electrical signal which, via an integrated circuit, controls its...

IR Kit for Arduino
Sale!
Price: $12.93
View
Availability: Back Order
Item #: DFR0107 -

This IR kit provides a remote control capability to your project. |Documents| Wiki Arduino Library (Compatible with Leonardo)|ShippingList| IR Remote Controller (With battery CR2025 inside) x1 IR Receiver Module x1 (SKU: DFR0094) Digital Cable x1|Projects|Project 1. Summer inspiration-DIY automatic curtain liftList of hardware: 1. Romeo-All in one Controller(DFR0004) 2. IR Kit(DFR0107) 3. Adjustable Infrared Sensor Switch (SEN0019) 4. DC motor (12V- FIT0493, FIT0277)5. 12V power adapter6....

DFRduino UNO SMD (Arduino Compatible)
Price: $36.02
View
Availability: Out of Stock
Item #: DFR0122 -

Introduction This is DFRduino UNO (SMD version).  It is a totally Arduino UNO compatible clone - just at a reduced price. The Arduino UNO is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a...

Capacitive Touch Kit For Arduino
Sale!
Price: $33.62
View
Availability: Back Order
Item #: DFR0129 -

Now, it is time to add a more fancy interactive way to your project. This DFRobot touch kit comes with three types touch sensors. An ipod styple wheel touch, a keypad touch which supports backlit and a grid touch pad which can recoginze something unique. This kit utilizes the not very "latest" capactive touch technology which make the sensing very sensitive. The kit is designed to be compatible with Arduino. Get Started with Capacitive Touch Kit Tutorial|Specification| Operation Voltage:5V...

Proto Screw Shield-Assembled (Arduino Compatible)
Sale!
Price: $22.32
View
(1)
Availability: Stocked
Item #: DFR0131 -

Combines the power of screw shield and prototyping shield. This Proto Screw shield offers a better way to do prototyping. The Screw terminal can be screwed directly to the terminal on the thread and is reliable and convenient. It can be plugged into the Arduino controller. You can use this shield to save yourself from the bad port connection. Feel secure with this arduino-compatible screw shield. The prototyping shield provides a fast prototpying area for projects. It features a LED (D13) and...

Breadboard Power Supply 5V/3.3V
Price: $7.84
View
Availability: Out of Stock
Item #: DFR0140 -

This is a very simple board that takes a 6-12V input voltage and outputs a selectable 5V or 3.3V regulated voltage. All headers are 0.1" pitch for simple insertion into a breadboard. It can be either powered from 6-12 DC2.1 power jack or from USB power.  The maximum current it can provide is 500mA.  Specification Input voltage: 6-12V (Power Jack) 5V (USB) Output voltage:3.3V/5V Output current:500mA On/Off switch Power status LED Pin Head 5/3.3V output Central positive DC2.1 power...

4 Channel Relay Shield for Arduino
Sale!
Price: $24.12
View
Availability: Back Order
Item #: DFR0144 -

This Relay Shield for Arduino acts like a switch. It is commonly used to control anything over 5V such as lamps, water pumps and garage doors. One of the most interesting projects for your boards is perhaps being able to control High power devices like Lamps, water pumps, garage doors and so on. But interfacing with high power and AC is quite a dangerous task when building the circuitry. Relays allow for interfacing an external electrical circuit like a switch. With relays you can now connect...

XBee USB Adapter V2 - Atmega8U2
Sale!
Price: $30.86
View
Availability: Back Order
Item #: DFR0174 -

The XBee USB Adapter V2 is an update version from DFRobot. It features an Atmega8U2 programmed as a USB-to-serial converter, the same chip found on the Arduino Uno. The Atmega8U2 firmware uses the standard USB COM drivers, and no external driver is needed. However, on Windows, a .inf file is required. It's compatible with all the products using XBee socket. It provides a faster and stable wireless communication for your projects. The DFRobot Xbee USB adapter is used for the XBee module...

DFRobot  Mega 2560 V3.0 (Arduino Mega 2560 R3 Compatible)
Sale!
Price: $42.92
View
Availability: Stocked
Item #: DFR0191 -

NEW VERSION! This is the upgraded DFRduino Mega 2560 V3.0 which is now fully compatible with Arduino Mega 2560 R3. The Arduino Mega is a microcontroller board based on the ATmega2560. It has 54 digital input/output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header and a reset button. It contains everything needed to support the microcontroller; Connect it to a computer...

Waterproof DS18B20 Digital Temperature Sensor for Arduino
Sale!
Price: $11.89
View
Availability: Back Order
Item #: DFR0198 -

This is a waterproofed version of the DS18B20 Temperature sensor. Handy for when you need to measure something far away, or in wet conditions. While the sensor is good up to 125°C the cable is jacketed in PVC so we suggest keeping it under 100°C. Because they are digital, you don't get any signal degradation even over long distances! The DS18B20 provides 9 to 12-bit (configurable) temperature readings over a 1-Wire interface, so that only one wire (and ground) needs to be connected...

Cheapduino (5Pcs)
Sale!
Price: $36.29
View
Availability: Stocked
Item #: DFR0236 -

CheapDuino is the most affordable Arduino compatible processor in the world. The price for each cheapDuino is almost 1/5 price of the Arduino UNO R3. It aims to provide an extremely low-cost solution for any disposable projects, such as DIY projects, workshop, gifts projects, E-Textiles and education. For those students from second or third world countries who can not afford the official Arduino, cheapduino opens the door to the physical world. The cheapDuino is integratd with an ATmega8...

MDV 2x2A DC Motor Controller (L298N)
Sale!
Price: $29.39
View
Availability: Back Order
Item #: DRI0002 -

This is a 4.8-46V, 2A Dual Motor Controller which is the revised version of the DF-MDV1.0. Its performance has been improved greatly. It can bear larger current due to the increased heat-sink dissipation. It is easy to control, using LGS's outstanding high-power motor driver chip, the L298N. This chip allows for direct drive of two bi-directional DC motors, and incorporates high-speed short diodes for protection. Drive current up to 2A per motor output. The driver uses a broad-brush design to...

2x2A DC Motor Shield for Arduino
Sale!
Price: $28.44
View
Availability: Back Order
Item #: DRI0009 -

Arduino product family is a great learning platform for electronics, programming and robotics. But most projects at some point require mobility. This Arduino motor shield allows for motor control with Arduino right away. Stack up this shield on your controller and drive 2 DC motors with higher power requirements. Depending on the motor of choice, you can make it fast or handle a higher payload. This Arduino Motor Shield (2A) uses L298P chip which allow to drive two 7-12V DC motors with maximum...

Mini Bread Board Self Adhesive - Black
Sale!
Price: $5.00
View
Availability: Back Order
Item #: FIT0008-BK -

This is a very small breadboard with 170 tie points. This bread board is compatible with the Arduino Proto Shield. Strong self-adhesive backing. Measures 1.8"x1.4".You also have choices of different colors. |Specification| 170 tie point breadboard 17 x 5 x 2 points Adhesive backing Black |ShippingList| Black 170 tie point bread board &;times;1

Medium Bread Board Self Adhsive
Sale!
Price: $12.93
View
Availability: Back Order
Item #: FIT0009 -

This is a medium size breadboard with 600 tie points. It has strong, self-adhesive backing. It is ideal for high frequency and low noise circuits. |Specification| Size:170*65mm (6.7x2.6 in) Suitable for 0.3-0.8 mm (0.01x0.03 in) wire|ShippingList| Medium Bread Board Self Adhsive x1

Digital Sensor Cable For Arduino (10 Pack)
Sale!
Price: $10.34
View
Availability: Back Order
Item #: FIT0011 -

The digital sensor cables are especially designed for our popular IO Expansion shield and sensors. It connects most of our digital sensor to the IO board. This price includes 10 pieces of cables.|Specification| Length:30cm (12 in) Maximum voltage:&;lt;50V Maximum current:&;lt;1000mA One Servo Type connector with Signal, GND PWR. One 3 Pin JST connector Red: PWR, Black:GND; Green: Signal|ShippingList| Digital Sensor Cable for Arduino (10 Pack) x1 ...

TT Geared Motor with Back Shaft (160rpm 6v L Shape)
Sale!
Price: $6.03
View
Availability: Back Order
Item #: FIT0016 -

This is a TT Micro DC Geared Motor with Back Shaft working at 6V with 160rpm. The TT motor series the most popular DC motors for DIY enthusiasts. It is designed to easily incorporate the DFRobot Encoder. These motors are inexpensive, small, easy to install, and ideally suited for use in a mobile robot. The DFRobot ROMEO microcontroller is able to complete the closed-loop PID making use of the Gravity:TT Motor Encoders Kit. We recommend this rubber wheel for this motor. |Specification|Electrical...

Cable for Shiftout
Sale!
Price: $4.48
View
Availability: Back Order
Item #: FIT0077 -

This cable is especially designed for Interface shield,shift out module, SPI Led and SPI LCD module. It is has a female 2&;times;3 IDC connector on each end that is designed to plug into a 0.100" (2.54 mm) 2&;times;3 shrouded box header. |Specification| Length:20cm (7.9&;#39;&;#39;) Female/Femal, IDC 2x3 Connector|ShippingList| Cable for Shiftout x1

6xAA  Battery Holder(double layer)
Sale!
Price: $2.15
View
Availability: Stocked
Item #: FIT0078 -

This battery holder can hold 6 AA battery which can make 7.2 V rechargeable battery pack from NiMH / NiCd cells or 9V battery pack from alkaline cells.It comes with a 6" Red & Black Wires with side by side & stack connection. |Specification| Cell Quantity: 6 Battery type: AA Storage temperature: 25&;#39;C (77F, RoomTemperature) Max Operate temperature: 80&;#39;C (176F)|ShippingList| 6xAA battery holder (double layer) x1 ...

Arduino Female  Header-8 Pins- 10 Pcs
Sale!
Price: $3.28
View
Availability: Back Order
Item #: FIT0104 -

This is a 8-pin female header which is used on Arduino board. |ShippingList| 8 Pin Header x10

40  Pin Break Away Male Header- Long Straight-10 Pcs
Sale!
Price: $8.71
View
Availability: Stocked
Item #: FIT0105 -

These are a longer version of our standard break away headers. They are 10mm long which allows you use them socket to socket. The plastic separator can be slid up or down to accommodate your needs. 40 pins that can be cut to any size. Used with custom PCBs or general custom headers. It is used on Arduino Ethernet Shield.|ShippingList| 40 Pin Header x10

1/4W Resistor Pack -2000 PCS
Sale!
Price: $26.81
View
Availability: Back Order
Item #: FIT0119 -

It comes with 20 of each value: 1R 1.2R 1.5R 1.8R 2R 2.2R 2.7R 3R 3.3R 3.9R 4.7R 5.1R 6.2R 6.8R 8.2R 10R 12R 15R 18R 20R 22R 27R 30R 33R 39R 47R 51R 62R 68R 82R 100R 120R 150R 180R 200R 220R 270R 300R 330R 390R 470R 510R 620R 680R 820R 1K 1.2K 1.5K 1.8K 2K 2.2K 2.7K 3K 3.3K 3.9K 4.7K 5.1K 6.2K 6.8K 8.2K 10K 12K 15K 18K 20K 22K 27K 30K 33K 39K 47K 51K 62K 68K 82K 100K 120K 150K 180K 200K 220K 270K 300K 330K 390K 470K 510K 620K 680K 820K 1M 1.2M 1.5M 1.8M 2M 2.2M 3.3M 3.9M 4.7M 5.1MNOTE: As this...

Jumper Wires (F/M)  (65 Pack)
Sale!
Price: $10.17
View
Availability: Stocked
Item #: FIT0121 -

Jumper wires are one of the most important gear component for the tinkerer. Often understimated, but one of the first things to miss. If you are starting to assemble your tinker gear and wondering if this is really needed, doubt not, this is at some point or another always used. Wire or pieces or wire are basic, even for the non-often tinkerers. Jumper wires are not just fitted for prototyping but also a resource for repurposing. You can cut them and add new headers, or mix them up and connect...