Enclosures

Why use a heatsink and a case, when you can use a heatsink case?! This black, anodized aluminum case for the Raspberry Pi 4 will give you 10-15°C of passive cooling under a full CPU load. This case...

Why use a heatsink and a case, when you can use a heatsink case?! This black, anodized aluminum case for the Raspberry Pi 4 will give you 10-15°C of passive cooling under a full CPU load. This case is great for situations where you want completely silent cooling, like home media centers. It comes with a thermal pad to provide thermal contact between the CPU and top case, and a handy Allen Key and set of hex bolts to attach the case together. The case gives you access to all of the ports, pins,...

A basic case with some not so basic features. The Argon POLY+ Raspberry Pi 4 Case uses a three piece snap-fit plastic design to protect your Pi 4 in a cost-effective way. The case has a two step...

A basic case with some not so basic features. The Argon POLY+ Raspberry Pi 4 Case uses a three piece snap-fit plastic design to protect your Pi 4 in a cost-effective way. The case has a two step cover similar to that of the Argon NEO which provides covered protection for the board while leaving the I/O ports accessible and includes a top cover which covers all but leaves room for most HATs and PHATs to sit inside. Also included is a heat sink for the processor and thermal tape to attach it. We...

This is the Big Red Box! These beefy, bright red, flanged, plastic enclosures will give your widget the protection (and attention) it deserves. You've probably seen these used to enclose radio...

This is the Big Red Box! These beefy, bright red, flanged, plastic enclosures will give your widget the protection (and attention) it deserves. You've probably seen these used to enclose radio equipment or antenna baluns as they can be secured to a pole using U-bolts (not included). At about 3mm thick, this 74x158x90mm enclosure has plenty of space for gizmos, gadgets, widgets and doohickeys. The mounting flanges extend 19mm from either edge with two 50mm-spaced 7mm diameter holes. There's a...

These are our small, beefy aluminum enclosures, which have been built tough enough to withstand a truck. This 2mm-thick, die-cast enclosure is rated IP54 against dust and splashing water. Because...

These are our small, beefy aluminum enclosures, which have been built tough enough to withstand a truck. This 2mm-thick, die-cast enclosure is rated IP54 against dust and splashing water. Because it's aluminum, it's easy to cut and drill so that you can add LCD screens, buttons and cable connections. If you want to "pretty up" your project, hit this with some fine-grit sand paper and buff it or just spray paint it! These enclosures are perfect for producing "stomp box" style effects pedals....

These are our large, beefy aluminum enclosures, which have been built tough enough to withstand a truck. This 2mm-thick, die-cast enclosure is rated IP54 against dust and splashing water. Because...

These are our large, beefy aluminum enclosures, which have been built tough enough to withstand a truck. This 2mm-thick, die-cast enclosure is rated IP54 against dust and splashing water. Because it's aluminum, it's easy to cut and drill so that you can add LCD screens, buttons and cable connections. If you want to "pretty up" your project, hit this with some fine-grit sand paper and buff it or just spray paint it! These enclosures are perfect for producing "stomp box"-style effects pedals....

The Mountable MI:pro is a simple and compact protective case for the micro:bit. This case has been specifically designed with portability and expansion in mind and is compatible with both the...

The Mountable MI:pro is a simple and compact protective case for the micro:bit. This case has been specifically designed with portability and expansion in mind and is compatible with both the original micro:bit V1 and the micro:bit V2. These cases feature a three-layer construction style with ability to wall-mount the whole assembly onto any surface you want while still providing access to all buttons and ports on the micro:bit. Though these cases do feature wall-mountable tabs, the biggest...

This MI:pro Protector Case for the BBC micro:bit has been designed to work with both the original micro:bit V1 and the micro:bit V2. These cases feature a four-layer construction style with ability...

This MI:pro Protector Case for the BBC micro:bit has been designed to work with both the original micro:bit V1 and the micro:bit V2. These cases feature a four-layer construction style with ability to mount a 2xAAA battery pack to the back of the case while still providing access to all buttons and ports on the micro:bit. Though these cases do protect the micro:bit astoundingly well, the biggest benefit of using the MI:pro is to not accidentally short out the pads on the back of the micro:bit....

The Raspberry Pi is everybody's favorite little computer, the last thing that you'd want is for something bad to happen to it. Why not protect it with one of these snazzy plastic enclosures? These...

The Raspberry Pi is everybody's favorite little computer, the last thing that you'd want is for something bad to happen to it. Why not protect it with one of these snazzy plastic enclosures? These cases protect the Raspberry Pi 3, the RPi 2, and Model B+ from things like rogue wires that might short it out while still allowing full access to the board! Simply snap the RPi into the bottom half of the enclosure, then snap the two sides together. As you may have noticed, these Pi Tins are...

The Raspberry Pi is THE new favorite of development platforms, so the last thing that you’d want is for something bad to happen to it. Why not protect it with one of these snazzy clear plastic...

The Raspberry Pi is THE new favorite of development platforms, so the last thing that you’d want is for something bad to happen to it. Why not protect it with one of these snazzy clear plastic enclosures? These clear cases protect the Raspberry Pi 3, RPi2, and Model B+ from things like rogue wires that might short it out while still allowing full access to the board as well as proper airflow to keep your new toy cool! Simply snap the RPi into the bottom half of the enclosure, then snap the two...

This is a basic baseplate for the Raspberry Pi 3 B/B+. It is translucent in color and provides a simple mounting solution for wherever you want to put your Pi! The baseplate is designed for the...

This is a basic baseplate for the Raspberry Pi 3 B/B+. It is translucent in color and provides a simple mounting solution for wherever you want to put your Pi! The baseplate is designed for the Raspberry Pi to securely remain on the acrylic by means of friction. The baseplate also aligns with the unit's forward mounting holes if you require additional security, but since screws are not required to form a firm connection, none are included. Includes: 1 Raspberry Pi 3B+ Baseplate Features:...

Note: This camera case does not currently fit the Raspberry Pi Camera Module V2. We are currently looking for a resolution to this issue. The Raspberry Pi is everybody's favorite little computer and...

Note: This camera case does not currently fit the Raspberry Pi Camera Module V2. We are currently looking for a resolution to this issue. The Raspberry Pi is everybody's favorite little computer and adding a Camera Module or Pi NoIR opens the door into video and photo capture, the last thing that you'd want is for something bad to happen to it. Why not protect your camera with one of these snazzy plastic enclosures? These cases protect the Raspberry Pi Camera Module from things like rogue...

The Raspberry Pi Zero Case has been designed to fit both the Pi Zero and the Pi Zero W. These official cases consist of several parts and protect the Raspberry Pi Zero from things like rogue wires...

The Raspberry Pi Zero Case has been designed to fit both the Pi Zero and the Pi Zero W. These official cases consist of several parts and protect the Raspberry Pi Zero from things like rogue wires that might short it out while still allowing full access to the board. Simply snap the RPi into the bottom half of the enclosure, then snap on a desired top. No tools required! Each case has a standard base featuring a cut-out to allow access to the GPIO, and a choice of three lids: a standard lid, a...