Sparkfun

This is the black silicone protective sock that is stretched over the RTK Facet or RTK Facet L-Band and is intended for users who need to repair a device. Open Source Hardware has the benefit of...

This is the black silicone protective sock that is stretched over the RTK Facet or RTK Facet L-Band and is intended for users who need to repair a device. Open Source Hardware has the benefit of allowing a user to understand and repair a broken device themselves! Note: This protective sock is compatible with the both the RTK Facet and the RTK Facet L-Band models. For more information please see the disassembly and repair instructions . Please see the recommended products below for additional...

This is a tiny USB Microphone from Kinobo that plugs into your laptop, desktop, Raspberry Pi, Jetson Nano Dev kit, anything with a USB port you may be using as a computer to add microphone...

This is a tiny USB Microphone from Kinobo that plugs into your laptop, desktop, Raspberry Pi, Jetson Nano Dev kit, anything with a USB port you may be using as a computer to add microphone functionality. There is no need to install any extra software as you OS should detect the device & automatically install it. Simply launch your program that requires microphone input and away we go! Note: This microphone is best used in a port that's not near your computer's cooling fan. Features: Works...

This is a simple 5V Op Amp breakout board, set up as a 2-stage amplifier with a gain of 100 (gain of 10 for each stage). The on-board trim pot sets the signal level between the stages, not the...

This is a simple 5V Op Amp breakout board, set up as a 2-stage amplifier with a gain of 100 (gain of 10 for each stage). The on-board trim pot sets the signal level between the stages, not the feedback path. The bandwidth is set to 15.9kHz by a pair of feedback capacitors, or over 100kHz with the caps removed. The LMV358 opamp can source up to 160mA and works well as a low impedance driver/buffer. Documents: Schematic Eagle Files Introduction to Op Amps with LTSpice Datasheet (LMV358) GitHub...

This tiny audio amplifier is based on the Texas Instruments TPA2005D1. Its efficient class-D operation means low heat and long battery life. It can drive an 8-Ohm speaker at up to 1.4 Watts; it...

This tiny audio amplifier is based on the Texas Instruments TPA2005D1. Its efficient class-D operation means low heat and long battery life. It can drive an 8-Ohm speaker at up to 1.4 Watts; it won't shake a stadium, but it will provide plenty of volume for your audio projects. The fully-differential inputs are safe for floating audio signals such as from our MP3 Shield, and can also be connected to ground-referenced signals as well. A shutdown input is provided to save power when the...

This breakout for the Silicon Laboratories Si4703 FM tuner chip is a little more stripped down than our FM Tuner Evaluation Board. If your project already has an amp and just needs a full-featured...

This breakout for the Silicon Laboratories Si4703 FM tuner chip is a little more stripped down than our FM Tuner Evaluation Board. If your project already has an amp and just needs a full-featured FM tuner, this is the board for you. Beyond being a simple FM radio, the Si4703 is also capable of detecting and processing both Radio Data Service (RDS) and Radio Broadcast Data Service (RBDS) information. The Si4703 even does a very good job of filtering and carrier detection. It also enables data...

Make some noise with your next project! The MP3 Trigger board is built to make MP3 sound integration easier than ever. The board has 18 external trigger pins that will directly trigger pre-selected...

Make some noise with your next project! The MP3 Trigger board is built to make MP3 sound integration easier than ever. The board has 18 external trigger pins that will directly trigger pre-selected MP3 tracks, and a full-duplex serial control port that provides full transport control, remote triggering for up to 256 tracks, and fast real-time volume control. MP3s are stored on FAT16 formatted SDSC or FAT32 formatted SDHC micro-SD flash memory cards. In addition, optimized code can achieve...

This is an evaluation board for the Silicon Laboratories Si4703 FM tuner chip. Beyond enabling you to tune in to FM radio stations, the Si4703 is also capable of detecting and processing both Radio...

This is an evaluation board for the Silicon Laboratories Si4703 FM tuner chip. Beyond enabling you to tune in to FM radio stations, the Si4703 is also capable of detecting and processing both Radio Data Service (RDS) and Radio Broadcast Data Service (RBDS) information. The Si4703 even does a very good job of filtering and carrier detection. It also enables data such as the station ID and song name to be displayed to the user. Using this board, you will be able to pick up multiple stations just...

The WAV Trigger is a unique high-fidelity polyphonic audio player with surprising capabilities. Supporting up to 2048 uncompressed 16-bit, 44.1kHz wav files – the same quality as an audio CD – the...

The WAV Trigger is a unique high-fidelity polyphonic audio player with surprising capabilities. Supporting up to 2048 uncompressed 16-bit, 44.1kHz wav files – the same quality as an audio CD – the WAV Trigger can play and mix up to 14 stereo tracks simultaneously and independently, with very low latency. Tracks can be controlled via 16 programmable trigger inputs, or by using a native serial control protocol or even MIDI. Trigger inputs can be connected directly to switches and buttons, or to...

WVR is a next-generation sample player powered by an ESP32. WVR features 8GB of memory and an advanced Web GUI where users upload audio and manage configuration and firmware. WVR is Arduino...

WVR is a next-generation sample player powered by an ESP32. WVR features 8GB of memory and an advanced Web GUI where users upload audio and manage configuration and firmware. WVR is Arduino compatible and open-source, and fits on a common breadboard, with room to access all the pins. WVR offers users a wide range of control over the device via the Web GUI, so the majority of embedded audio uses can be setup without writing custom code. WVR responds to MIDI input, or to events on the GPIO pins....

The SparkFun Qwiic Speaker Amp includes the Texas Instruments TPA2016D2 stereo, filter-free class-D audio power amplifier. What distinguishes this audio amplifier from others is that it features...

The SparkFun Qwiic Speaker Amp includes the Texas Instruments TPA2016D2 stereo, filter-free class-D audio power amplifier. What distinguishes this audio amplifier from others is that it features volume control (i.e. gain), Dynamic Range Compression (DRC), Automatic Gain Control (AGC), enable/disable amplifier, and its ability to be configured through software via I2C. Its efficient class-D operation also means low heat and long battery life when driving 4Ω speakers at up to 2.8W in stereo, and...

Based on a new generation ARM Cortex M7, this version of the Qwiic Tsunami Super WAV Trigger extends polyphony to 25 mono or 13 stereo simultaneous uncompressed 44.1kHz, 16-bit tracks. Each track...

Based on a new generation ARM Cortex M7, this version of the Qwiic Tsunami Super WAV Trigger extends polyphony to 25 mono or 13 stereo simultaneous uncompressed 44.1kHz, 16-bit tracks. Each track can start, pause, resume, loop, and stop independently, and can have its own volume setting, allowing you to create the perfect interactive mix of music, dialog, and sound effects. The Qwiic Tsunami also supports true seamless looping over an arbitrary track length. Utilizing our handy Qwiic system,...

The SparkFun Qwiic Speaker Kit provides you with just what you need to get started with stereo audio via a simple Qwiic interface! Included in this kit, you will find two thin speakers, all...

The SparkFun Qwiic Speaker Kit provides you with just what you need to get started with stereo audio via a simple Qwiic interface! Included in this kit, you will find two thin speakers, all connecting cables (that includes power and Qwiic), a wall adapter, as well as a SparkFun Qwiic Speaker Amp and RedBoard Artemis Nano. Thanks to the kit being Qwiic-enabled, no soldering is required, either! The SparkFun Qwiic Speaker Amp features the Texas Instruments TPA2016D2 stereo, filter-free class-D...

The 22.86 x 22.86mm Nicla Voice allows for easy implementation of always-on speech recognition on the edge, because it integrates Syntiant’s powerful NDP120 Neural Decision processor to run multiple...

The 22.86 x 22.86mm Nicla Voice allows for easy implementation of always-on speech recognition on the edge, because it integrates Syntiant’s powerful NDP120 Neural Decision processor to run multiple AI algorithms, leveraging bio-inspired, advanced machine learning to automate complex tasks. Nicla Voice comes with a comprehensive package of sensors: in addition to its microphone, it features a smart 6-axis motion sensor and a magnetometer, making it the ideal solution for predictive...

The SparkFun WM8960 Audio Codec Breakout is a low-power, high-quality stereo codec with 1W Stereo Class D speaker drivers and headphone drivers. The WM8960 acts as a stereo audio ADC and DAC and...

The SparkFun WM8960 Audio Codec Breakout is a low-power, high-quality stereo codec with 1W Stereo Class D speaker drivers and headphone drivers. The WM8960 acts as a stereo audio ADC and DAC and communicates using I2S, a standard audio data protocol (not to be confused with I2C). This audio codec is chock full of features some of which include advanced on-chip digital signal processing for automatic level control (ALC) for the line or microphone input, programmable gain amplifier (PGA), pop...

The SparkFun WM8960 Audio Codec Breakout is a low-power, high-quality stereo codec with 1W Stereo Class D speaker drivers and headphone drivers. The WM8960 acts as a stereo audio ADC and DAC and...

The SparkFun WM8960 Audio Codec Breakout is a low-power, high-quality stereo codec with 1W Stereo Class D speaker drivers and headphone drivers. The WM8960 acts as a stereo audio ADC and DAC and communicates using I2S, a standard audio data protocol (not to be confused with I2C). This audio codec is chock full of features some of which include advanced on-chip digital signal processing for automatic level control (ALC) for the line or microphone input, programmable gain amplifier (PGA), pop...

WVR is a next-generation sample player powered by an ESP32. WVR features 8GB of memory and an advanced Web GUI where users upload audio and manage configuration and firmware. WVR is Arduino...

WVR is a next-generation sample player powered by an ESP32. WVR features 8GB of memory and an advanced Web GUI where users upload audio and manage configuration and firmware. WVR is Arduino compatible and open-source, and fits on a common breadboard, with room to access all the pins. WVR offers users a wide range of control over the device via the Web GUI, so the majority of embedded audio uses can be setup without writing custom code. WVR responds to MIDI input, or to events on the GPIO pins....

You won't need a series four de-atomizer with our rendition of the Noisy Cricket, just wire it up and crank up your tunes! The Noisy Cricket Stereo Amplifier, uses the LM4853 Boomer® IC which can be...

You won't need a series four de-atomizer with our rendition of the Noisy Cricket, just wire it up and crank up your tunes! The Noisy Cricket Stereo Amplifier, uses the LM4853 Boomer® IC which can be configured to output up to 1.5W of power in mono operation (4Ω load) or 300mW per channel in stereo operation (8Ω load). The amplifier comes with a dual-ganged pot with a built-in switch to control power and adjust both left and right channel gain. The SparkFun Noisy Cricket has been designed as an...

The SparkFun I2S Audio Breakout board uses the MAX98357A digital to analog converter (DAC), which converts I2S (not be confused with I2C) audio to an analog signal to drive speakers. The I2S Audio...

The SparkFun I2S Audio Breakout board uses the MAX98357A digital to analog converter (DAC), which converts I2S (not be confused with I2C) audio to an analog signal to drive speakers. The I2S Audio Breakout converts the digital audio signals using the I2S standard to an analog signal and amplifies the signal using a class D amplifier which can deliver up to 3.2W of power into a 4Ω load. The board can be configured to output only the left channel audio, right channel, or both. The SparkFun I2S...

Do you make time to talk to your Arduino? Maybe you should! The EasyVR 3 Plus Shield is a voice recognition shield for Arduino boards integrating an EasyVR module. This kit includes the EasyVR 3...

Do you make time to talk to your Arduino? Maybe you should! The EasyVR 3 Plus Shield is a voice recognition shield for Arduino boards integrating an EasyVR module. This kit includes the EasyVR 3 Plus Module, the Arduino Shield Adapter, microphone, and headers. With all of these parts, everything has been provided to you to get up and running in a short amount of time with minimal soldering! EasyVR 3 Plus is a multi-purpose speech recognition module designed to add versatile, robust and cost...

The SparkFun Analog MEMS Microphone Breakout makes it easy to work with the InvenSense ICS-40180 analog microphone. This board features an OpAmp to bring output of the microphone to a usable level,...

The SparkFun Analog MEMS Microphone Breakout makes it easy to work with the InvenSense ICS-40180 analog microphone. This board features an OpAmp to bring output of the microphone to a usable level, allowing you to plug directly into an ADC on a microcontroller or something like the SparkFun Spectrum Shield. In addition to amplifying the signal, the OpAmp adds a bias voltage of 1/2 VCC. With sound sources such as a normal speaking voice a few feet away from the microphone, the AUD output signal...

Based on a new generation ARM Cortex M7, the Qwiic Tsunami Super WAV Trigger extends polyphony to 32 mono or 18 stereo simultaneous uncompressed 44.1kHz, 16-bit tracks. Each track can start, pause,...

Based on a new generation ARM Cortex M7, the Qwiic Tsunami Super WAV Trigger extends polyphony to 32 mono or 18 stereo simultaneous uncompressed 44.1kHz, 16-bit tracks. Each track can start, pause, resume, loop and stop independently, and can have its own volume setting, allowing you to create the perfect interactive mix of music, dialog and sound effects. The Qwiic Tsunami also supports true seamless looping over an arbitrary track length. Utilizing our handy Qwiic system, no soldering is...

The SparkFun Analog MEMS Microphone Breakout makes it easy to work with the SPH8878LR5H-1 analog microphone from Knowles. This board features an OpAmp to bring the output of the microphone to a...

The SparkFun Analog MEMS Microphone Breakout makes it easy to work with the SPH8878LR5H-1 analog microphone from Knowles. This board features an OpAmp to bring the output of the microphone to a usable level, allowing you to plug directly into an ADC on a microcontroller or something like the SparkFun Spectrum Shield. In addition to amplifying the signal, the OpAmp adds a bias voltage of 1/2 VCC. With sound sources such as a normal speaking voice a few feet away from the microphone, the AUD...

Add some crisp and compact audio to your project with this Mini External USB 2.0 Speaker. It's USB-only and does not require or use a 3.5mm audio jack. You'll get great audio, even with a device...

Add some crisp and compact audio to your project with this Mini External USB 2.0 Speaker. It's USB-only and does not require or use a 3.5mm audio jack. You'll get great audio, even with a device that doesn't have a head phone jack. Since this speaker is powered over USB, there's no need to charge it by other means, merely plug it into your desired device's USB port and listen to the audio flow. Compact and convenient to carry, it's simple and practical. With two built-in speakers and no...

This is a small 12mm round speaker that operates around the audible 2kHz range. You can use these speakers to create simple music or user interfaces. This is not a true piezoelectric speaker but...

This is a small 12mm round speaker that operates around the audible 2kHz range. You can use these speakers to create simple music or user interfaces. This is not a true piezoelectric speaker but behaves similarly. Instead of a piezoelectric crystal that vibrates with an electric current, this tiny speaker uses an electromagnet to drive a thin metal sheet. That means you need to use some form of alternating current to get sound. The good news is that this speaker is tuned to respond best with a...

This Piezo Alarm is a great option for when you need an audible alarm (or are just looking for a way to prank your friends). This alarm has 16 different output options that can be changed with the...

This Piezo Alarm is a great option for when you need an audible alarm (or are just looking for a way to prank your friends). This alarm has 16 different output options that can be changed with the DIP switches on the unit. Select Continuous, Chime, Intermittent, Warble, or Pulsating and amaze your friends. Features: Operating Voltage: 5-16Vdc Operating Frequency: 3KHz Warble Frequency: 2.8KHz to 3.2KHz Diameter: 35.8mm, Height 35.7mm 103 dB(A) at 16V at 61cm 90 dB(A) at 5V at 61cm Documents:...

The SparkFun Qwiic Buzzer adds simple beeps and buzzes to your projects via I2C. Make some noises to alert you when something interesting (or urgent) happens. Simply connect a Qwiic cable and load...

The SparkFun Qwiic Buzzer adds simple beeps and buzzes to your projects via I2C. Make some noises to alert you when something interesting (or urgent) happens. Simply connect a Qwiic cable and load up some pre-written code to an Arduino to start making noises! The board includes an ATtiny84 with custom firmware to control the magnetic buzzer over I2C. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still broke out 0.1"-spaced PTH...

A small audio speaker that is ideal for radio and amplifier projects and is small enough to fit in robot projects. Features: Small Size Power rating: 0.5W Impedance: 8Ω 50mm diameter, 16mm high,...

A small audio speaker that is ideal for radio and amplifier projects and is small enough to fit in robot projects. Features: Small Size Power rating: 0.5W Impedance: 8Ω 50mm diameter, 16mm high, 28mm base diameter

This through-hole speaker is great for projects where you need something that sounds better than a piezo buzzer but don't have room for a full-blown speaker. This 30mm diameter speaker is encased in...

This through-hole speaker is great for projects where you need something that sounds better than a piezo buzzer but don't have room for a full-blown speaker. This 30mm diameter speaker is encased in plastic and will handle about 100mW of power. Features: 8 ohm 0.1W (0.2W max) 30mm diameter Documents: Datasheet Product Video ...

If you want to get some sound out of your project but have a tight space budget, this is a good way to do it. This 2.5W, 4 Ohm speaker is only 28mm in diameter and just over 4mm thick. The cable is...

If you want to get some sound out of your project but have a tight space budget, this is a good way to do it. This 2.5W, 4 Ohm speaker is only 28mm in diameter and just over 4mm thick. The cable is roughly 180mm long and terminates in a 2-wire JST connector.

This will be a treat for your ears! The Hamburger Mini Speaker is a 3W economical speaker option for any project needing stand-alone sound. The Hamburger features a built-in lithium polymer battery...

This will be a treat for your ears! The Hamburger Mini Speaker is a 3W economical speaker option for any project needing stand-alone sound. The Hamburger features a built-in lithium polymer battery for portable application, a 3.5mm stereo jack (sorry, iPhone 7 users) and two volume options (quiet and loud) to control how loud your sound needs to be. This speaker really can't be compared to a good pair of JBLs, but for the price point the Hamburger won't break the bank for your next audiophile...

If you want to get some sound out of your project but have a tight space budget, this is a good way to do it. This 0.5W, 8Ohm speaker is only 40mm in diameter and just over 4mm thick, the same kind...

If you want to get some sound out of your project but have a tight space budget, this is a good way to do it. This 0.5W, 8Ohm speaker is only 40mm in diameter and just over 4mm thick, the same kind you might find in one of those "talking greeting cards". Documents: Datasheet Dimensional Drawing ...

This is a small 15mm round speaker that operates around the audible 2kHz range. You can use these speakers to create simple music or user interfaces. This through-hole speaker is great for projects...

This is a small 15mm round speaker that operates around the audible 2kHz range. You can use these speakers to create simple music or user interfaces. This through-hole speaker is great for projects where you don't have room for a full-blown speaker. This 15mm diameter speaker is encased in plastic and will handle up to 0.5W of power. Features: Diameter 15 mm Depth 7.5 mm Input Power: Min. 0.3W, Max. 0.5W Impedance at 3 kHz, 1 V: Min. 6.8Ω, Typ. 8Ω, Max. 9.2Ω Resonant Frequency at 1V: Min....

This wide range speaker is an excellent choice for compact applications requiring high fidelity music, or high intelligibility voice/communications audio. A talc-filled, polypropylene cone with a...

This wide range speaker is an excellent choice for compact applications requiring high fidelity music, or high intelligibility voice/communications audio. A talc-filled, polypropylene cone with a rubber surround allows this driver to be used either indoors or outdoors. Ideal applications for this speaker include home theaters, alarm and security systems, gaming and arcade cabinets, kiosk audio, smart devices, and more. Features: Size, Nominal (inch & mm): 3" (77 mm) Shape of Speaker:...

Surface transducers give you the awesome power to turn almost any surface into a speaker. They're essentially just a speaker except instead of a cone, the coil is attached to a pad that conducts the...

Surface transducers give you the awesome power to turn almost any surface into a speaker. They're essentially just a speaker except instead of a cone, the coil is attached to a pad that conducts the vibration into whatever you press it against. Hook it up to an audio source and press it against the nearest table, wall or cardboard box. You can even put it against your head and play music directly into your skull (the ultimate surround sound). This transducer comes with an adhesive magnet that...

VS1063 is an easy-to-use, versatile encoder, decoder and codec for a multitude of audio formats. They can be hard to get hold of but we've got them! The VS1063 contains a high-performance,...

VS1063 is an easy-to-use, versatile encoder, decoder and codec for a multitude of audio formats. They can be hard to get hold of but we've got them! The VS1063 contains a high-performance, proprietary, low-power DSP core as well as ROM memory, 16KiB instruction RAM and up to 80 KiB data RAM for user applications running simultaneously with any built-in decoder! There's built-in serial control and input data interfaces, up to 12 general purpose I/O pins, a UART, as well as specialized...

The AS358P is a great, easy-to-use dual-channel Op-amp. Op-amps have so many applications we figured we should probably carry at least one in a DIP package. AS358P applications include transducer...

The AS358P is a great, easy-to-use dual-channel Op-amp. Op-amps have so many applications we figured we should probably carry at least one in a DIP package. AS358P applications include transducer amplifiers, DC gain blocks and all the conventional op-amp circuits. If you're looking for a good, standard op-amp the AS358P should fill most of your needs. It can handle a supply of 3-36VDC and source up to 20mA per channel. This op-amp is great if you need to operate two individual op-amps from a...

This is a foot-long white audio cable that has been terminated with two TRRS connectors at each end. TRRS connectors are the 3.5mm audio-style connectors that you see on some phones, MP3 players and...

This is a foot-long white audio cable that has been terminated with two TRRS connectors at each end. TRRS connectors are the 3.5mm audio-style connectors that you see on some phones, MP3 players and development boards. TRRS stands for “Tip, Ring, Ring, Sleeve,” which reflects the fact that, unlike a standard stereo connector, this actually has three conductors and a ground. Some devices use the extra conductor for a microphone (as in hands-free headsets) or to carry a video signal (as in some...

This is an Audio to Alligator Cable, an 8in. long 22 AWG wire with two alligator clips at one end and a 2.5mm mono plug at the other. Documents: Datasheet ...

This is an Audio to Alligator Cable, an 8in. long 22 AWG wire with two alligator clips at one end and a 2.5mm mono plug at the other. Documents: Datasheet

TRS connectors are the audio-style connectors that you see on some phones, MP3 players and development boards. TRS stands for "Tip, Ring, Sleeve." If you're hacking on something that has a...

TRS connectors are the audio-style connectors that you see on some phones, MP3 players and development boards. TRS stands for "Tip, Ring, Sleeve." If you're hacking on something that has a three-conductor audio jack (such as the MyoWare® 2.0 Link Shield), being able to plug straight in will keep your build clean and simple. This cable has a standard TRS 3.5mm plug on both ends allowing for easy connections to any 3.5mm jack. Note: The MyoWare 2.0 Link Shield shown in the image is NOT included....

These are various leaded cables for attaching to multimeters, power supplies, oscilloscopes, function generators, etc. 5 pairs of IC Hook to IC Hook test leads. Comes with Black, Red, Blue, Green,...

These are various leaded cables for attaching to multimeters, power supplies, oscilloscopes, function generators, etc. 5 pairs of IC Hook to IC Hook test leads. Comes with Black, Red, Blue, Green, and Yellow colored leads. Features: 14" Long

These are various leaded cables for attaching to multimeters, power supplies, oscilloscopes, function generators, etc. Features: 36" Long

These are various leaded cables for attaching to multimeters, power supplies, oscilloscopes, function generators, etc. Features: 36" Long

These are various leaded cables for attaching to multimeters, power supplies, oscilloscopes, function generators, etc. Cables come in red/black pairs. Features: 36" Long ...

These are various leaded cables for attaching to multimeters, power supplies, oscilloscopes, function generators, etc. Cables come in red/black pairs. Features: 36" Long

These are various leaded cables for attaching to multimeters, power supplies, oscilloscopes, function generators, etc. Cables come in red/black pairs. Features: 36" Long ...

These are various leaded cables for attaching to multimeters, power supplies, oscilloscopes, function generators, etc. Cables come in red/black pairs. Features: 36" Long

These are various leaded cables for attaching to multimeters, power supplies, oscilloscopes, function generators, etc. High quality coax cable with stress relief sleeves. Features: 36" long ...

These are various leaded cables for attaching to multimeters, power supplies, oscilloscopes, function generators, etc. High quality coax cable with stress relief sleeves. Features: 36" long

These are various leaded cables for attaching to multimeters, power supplies, oscilloscopes, function generators, etc. Cables come in red/black pairs. Features: 36" long ...

These are various leaded cables for attaching to multimeters, power supplies, oscilloscopes, function generators, etc. Cables come in red/black pairs. Features: 36" long

This is a simple 10-pin cable. There is a 10-pin connector with 0.1" spacing on both ends.

This is a simple 10-pin cable. There is a 10-pin connector with 0.1" spacing on both ends.

This is a handy cable for connecting a six pin GHR-06V-S type locking connector to a four pin GHR-04V-S type locking connector. The cable features a 1.25mm pitch GHR-06V-S & GHR-04V-S 'locking' JST...

This is a handy cable for connecting a six pin GHR-06V-S type locking connector to a four pin GHR-04V-S type locking connector. The cable features a 1.25mm pitch GHR-06V-S & GHR-04V-S 'locking' JST connector commonly found on some sensors, radios, and other small devices. You can cut and strip to have your own four pin or six pin cable with GHR 1.25mm pitch connectors. The wires can also be removed with an exacto knife to move pins around as needed.

This is a handy cable for connecting a six pin GHR-06V type locking connector to breadboard friendly male pins. The cable features a 1.25mm pitch GHR-06V 'locking' JST connector commonly found on...

This is a handy cable for connecting a six pin GHR-06V type locking connector to breadboard friendly male pins. The cable features a 1.25mm pitch GHR-06V 'locking' JST connector commonly found on some sensors, radios, and other small devices. Features: *28 AWG Documents: Drawing

This is a 50mm long ESLOV to ESLOV cable. The ESLOV connector has five pins (one more than standard I2C) for automatically configuring the module and handling the sleeping states to boost battery...

This is a 50mm long ESLOV to ESLOV cable. The ESLOV connector has five pins (one more than standard I2C) for automatically configuring the module and handling the sleeping states to boost battery life. Use this cable to connect two ESLOV boards together, or use this along with the SparkFun ESLOV to Qwiic Bridge to connect ESLOV compatible boards with Qwiic compatible boards. Documents: Drawing ...

This is a basic SMA (Sub-Miniature A) male to female connector cable. Each cable is 1M (39.3in.) long with RG174 housing. The SMA connectors at each end are small enough for most consumer GPS,...

This is a basic SMA (Sub-Miniature A) male to female connector cable. Each cable is 1M (39.3in.) long with RG174 housing. The SMA connectors at each end are small enough for most consumer GPS, cellular, and other RF applications and they use a threaded housing to create strong mechanical connections. These work well for mounting an antenna to the outside of an enclosure, while keeping the electronics neatly inside. Documents: Mechanical Drawing ...

This is a basic RP-SMA (Reverse Polarity Sub-Miniature A) male to female connector cable. Each cable is 1M (39.3in.) long with RG174 housing. The RP-SMA connectors at each end are small enough for...

This is a basic RP-SMA (Reverse Polarity Sub-Miniature A) male to female connector cable. Each cable is 1M (39.3in.) long with RG174 housing. The RP-SMA connectors at each end are small enough for most consumer GPS, cellular, and other RF applications and they use a threaded housing to create strong mechanical connections. These work well for mounting an antenna to the outside of an enclosure, while keeping the electronics neatly inside. Documents: Mechanical Drawing ...

This is a basic RP-SMA (Reverse Polarity Sub-Miniature A) male to female connector cable. Each cable is 25cm (9.8in.) long with RG174 housing. The RP-SMA connectors at each end are small enough for...

This is a basic RP-SMA (Reverse Polarity Sub-Miniature A) male to female connector cable. Each cable is 25cm (9.8in.) long with RG174 housing. The RP-SMA connectors at each end are small enough for most consumer GPS, cellular, and other RF applications and they use a threaded housing to create strong mechanical connections. These work well for mounting an antenna to the outside of an enclosure, while keeping the electronics neatly inside. Documents: Mechanical Drawing ...

This is a basic RP-SMA (Reverse Polarity Sub-Miniature A) male to female connector cable. Each cable is 10M (393.7in.) long with RG58 housing. The RP-SMA connectors at each end are small enough for...

This is a basic RP-SMA (Reverse Polarity Sub-Miniature A) male to female connector cable. Each cable is 10M (393.7in.) long with RG58 housing. The RP-SMA connectors at each end are small enough for most consumer GPS, cellular, and other RF applications and they use a threaded housing to create strong mechanical connections. These work well for mounting an antenna to the outside of an enclosure, while keeping the electronics neatly inside. Documents: Mechanical Drawing ...

This product is designed to connect the RTK Surveyor product line to the popular Serial Telemetry Radios. But if you're like me, it's great to have the right connector and terminated wires for other...

This product is designed to connect the RTK Surveyor product line to the popular Serial Telemetry Radios. But if you're like me, it's great to have the right connector and terminated wires for other applications! You can cut and strip to have your own 4 pin or 6 pin cable with GHR 1.25mm pitch connectors. The wires can also be removed with an exacto knife to move pins around as needed. Documents: GHR Connector Datasheet ...

This is a handy cable for connecting a four pin GHR-04V type locking connector to breadboard friendly male pins. These cables are already included with the RTK Surveyor product line, but the GHR...

This is a handy cable for connecting a four pin GHR-04V type locking connector to breadboard friendly male pins. These cables are already included with the RTK Surveyor product line, but the GHR connector is common and may also be seen on other products and sensors. Documents: GHR Connector Datasheet

This is a servo adapter cable that allows you to hookup your servo directly to alligator clip connections. On one end you have a shrouded male servo connector, and on the other end three 30mm...

This is a servo adapter cable that allows you to hookup your servo directly to alligator clip connections. On one end you have a shrouded male servo connector, and on the other end three 30mm shrouded alligator clips. Alligator clips are a staple item for any workbench or maker space, and with these cables you will be able to easily incorporate those clips into any project you are working on that involves a servo connection. Features: 26 AWG Length: 170mm Documents: Schematic ...

This servo cable has a shrouded male servo connector on one end, and 3x breadboard hookup pigtails at the other end. This makes it easy to connect your servo into a breadboard, development platform...

This servo cable has a shrouded male servo connector on one end, and 3x breadboard hookup pigtails at the other end. This makes it easy to connect your servo into a breadboard, development platform or anything else to which you would normally be able to attach a hookup wire. Features: 26 AWG Length: 170mm Documents: Schematic ...

The MyoWare® 2.0 Reference Cable is meant as an extension for the MyoWare 2.0 Muscle Sensor's reference pin. You will just need to insert the pin into its housing and place a biomedical sensor pad...

The MyoWare® 2.0 Reference Cable is meant as an extension for the MyoWare 2.0 Muscle Sensor's reference pin. You will just need to insert the pin into its housing and place a biomedical sensor pad into the electrode snap. When ready, stick the reference cable's snap pin to a separate section of the body such as a bony portion of the elbow or a nonadjacent muscle near a targeted muscle where the MyoWare 2.0 Muscle Sensor's built-in reference pin is unable to reach. Note: The reference electrode...

This is a 10 pack of the MyoWare® Reference 2.0 Cables. The MyoWare 2.0 Reference Cable is meant as an extension for the MyoWare 2.0 Muscle Sensor's reference pin. You will just need to insert the...

This is a 10 pack of the MyoWare® Reference 2.0 Cables. The MyoWare 2.0 Reference Cable is meant as an extension for the MyoWare 2.0 Muscle Sensor's reference pin. You will just need to insert the pin into its housing and place a biomedical sensor pad into the electrode snap. When ready, stick the reference cable's snap pin to a separate section of the body such as a bony portion of the elbow or a nonadjacent muscle near a targeted muscle where the MyoWare 2.0 Muscle Sensor's built-in...

When experimenting with GPS or RF it can be very handy to have the antenna on the top of your house or car with a clear view of the sky while you stay in doors and warm at your keyboard. This 2m...

When experimenting with GPS or RF it can be very handy to have the antenna on the top of your house or car with a clear view of the sky while you stay in doors and warm at your keyboard. This 2m (6.5ft) magnetic mount SMA extension does a great job of connecting your receiver or radio to a distant antenna with as little RF loss as possible. The cable is the thicker, lower loss, RG58 which is ideal for high power (≥100mW) transmissions. While the magnetic strength is high, it is not intended...

This is a basic SMA (Sub-Miniature A) male to female connector cable. Each cable is 25cm (9.8in.) long with RG174 housing. The SMA connectors at each end are small enough for most consumer GPS,...

This is a basic SMA (Sub-Miniature A) male to female connector cable. Each cable is 25cm (9.8in.) long with RG174 housing. The SMA connectors at each end are small enough for most consumer GPS, cellular, and other RF applications and they use a threaded housing to create strong mechanical connections. These work well for mounting an antenna to the outside of an enclosure, while keeping the electronics neatly inside. Documents: Mechanical Drawing ...

This is a handy cable for connecting a six pin GHR-06V type locking connector to breadboard friendly male pins. The six male pins that terminate one side of the cable feature a 1.25mm pitch while...

This is a handy cable for connecting a six pin GHR-06V type locking connector to breadboard friendly male pins. The six male pins that terminate one side of the cable feature a 1.25mm pitch while the GHR-06V JST is typically used in PDP, LCD, or small electronics equipment. Features: 28 AWG Documents: Datasheet ...

This is a 4-pin JST-ZHR cable that's terminated on the end with breadboard compatible Dupont connectors. The four male pins that terminate one side of the cable feature a 1.5mm pitch while the...

This is a 4-pin JST-ZHR cable that's terminated on the end with breadboard compatible Dupont connectors. The four male pins that terminate one side of the cable feature a 1.5mm pitch while the JST-ZHR JST provides a secure locking device to ensure connector-mating integrity even under adverse conditions. Features: 28 AWG Documents: Datasheet ...

This is a 6-pin JST-ZHR cable that's terminated on the end with breadboard compatible Dupont connectors. The six male pins that terminate one side of the cable feature a 1.5mm pitch while the...

This is a 6-pin JST-ZHR cable that's terminated on the end with breadboard compatible Dupont connectors. The six male pins that terminate one side of the cable feature a 1.5mm pitch while the JST-ZHR JST provides a secure locking device to ensure connector-mating integrity even under adverse conditions. Features: 28 AWG Documents: Datasheet ...