Movement

This is the new version of the Sabertooth 2x10 motor controller. The Sabertooth 2X12 is one of the most versatile, efficient and easy to use dual motor drivers on the market. It is suitable for...

This is the new version of the Sabertooth 2x10 motor controller. The Sabertooth 2X12 is one of the most versatile, efficient and easy to use dual motor drivers on the market. It is suitable for medium powered robots - up to 30lbs in combat or 100lbs for general purpose robotics. Out of the box, the Sabertooth can supply two DC brushed motors with up to 12A each. Peak currents of 15A are achievable for a few seconds. Overcurrent and thermal protection means you&;#39;ll never have to worry about...

The Sabertooth 2X25 is one of the most versatile, efficient and easy to use dual motor drivers on the market. It is suitable for high powered robots - up to 100lbs in combat or 300lbs for general...

The Sabertooth 2X25 is one of the most versatile, efficient and easy to use dual motor drivers on the market. It is suitable for high powered robots - up to 100lbs in combat or 300lbs for general purpose robotics. Out of the box, the Sabertooth can supply two DC brushed motors with up to 25A each. Peak currents of 50A per channel are achievable for a few seconds. Overcurrent and thermal protection means you'll never have to worry about killing the driver with accidental stalls or by hooking up...

"Here is a simple, low-cost, high quality servo for all your mechatronic needs. This servo is able to take in 6 volts and deliver 44.4 oz-in. of maximum torque at 0.18 sec/60° This is a small...

"Here is a simple, low-cost, high quality servo for all your mechatronic needs. This servo is able to take in 6 volts and deliver 44.4 oz-in. of maximum torque at 0.18 sec/60° This is a small servo with a standard 3 pin power and control cable (red = power, brown = ground, and yellow = data), and all hardware listed below. Features: Voltage: 4.8-6.0 Volts Torque: 38.8/44.4 oz-in. (4.8/6.0V) Speed: 0.20/0.18 sec/60° (4.8/6.0V) Rotation: 180° Dual Ball Bearing Metal Gears...

This is a 150mm (5.91") servo extension cable. This comes in very handy when your servo is further away from the controller than the wire on the servo allows. Male connector on one end goes to...

This is a 150mm (5.91") servo extension cable. This comes in very handy when your servo is further away from the controller than the wire on the servo allows. Male connector on one end goes to controller, female connector mates with servo. Fits all Hitec, Futaba, JR, Multiplex, and Airtronics Z servos. Wire can also be used as a simple 0.1" jumper cable. |Specification| Length:150mm Red: PWR, Black:GND, White:Signal |ShippingList| Servo extension cable 150mm (5.91") x1 ...

This is a 300mm servo extension cable. This comes in very handy when your servo is further away from the controller than the wire on the servo allows. Male connector on one end goes to controller,...

This is a 300mm servo extension cable. This comes in very handy when your servo is further away from the controller than the wire on the servo allows. Male connector on one end goes to controller, female connector mates with servo. Fits all Hitec, Futaba, JR, Multiplex, and Airtronics Z servos. Wire can also be used as a simple 0.1" jumper cable.|Specification| Length:300mm (11.8 in)|ShippingList| 300mm Servo extension cable x1

This is a 600mm (23.62") servo extension cable. This comes in very handy when your servo is further away from the controller than the wire on the servo allows. Male connector on one end goes to...

This is a 600mm (23.62") servo extension cable. This comes in very handy when your servo is further away from the controller than the wire on the servo allows. Male connector on one end goes to controller, female connector mates with servo. Fits all Hitec, Futaba, JR, Multiplex, and Airtronics Z servos. Wire can also be used as a simple 0.1" jumper cable. |Specification| Length: 600mm (23.62") Red: VCC Black: GND White: Signal|ShippingList| Servo extension cable 600mm (23.62") x1 ...

This 300mm Y-cable is typically used to connect two servos to a single servo port on an RC receiver or servo controller. It has a single female JR connector connected to two male JR connectors,...

This 300mm Y-cable is typically used to connect two servos to a single servo port on an RC receiver or servo controller. It has a single female JR connector connected to two male JR connectors, which means it is compatible with almost all of the RC servos.The connectors have gold-flashed contacts on a 0.1" spacing.The split occurs near the midpoint of the cable, so the two male ends can be separated by up to approximately 300mm. Black: GND Red?Servo power White?Signal |Applications| RC car,...

This 500 mm Y-cable is typically used to connect two servos to a single servo port on an RC receiver or servo controller. It has a single female JR connector connected to two male JR connectors,...

This 500 mm Y-cable is typically used to connect two servos to a single servo port on an RC receiver or servo controller. It has a single female JR connector connected to two male JR connectors, which means it is compatible with almost all of the RC servos.The connectors have gold-flashed contacts on a 0.1" spacing.The split occurs near the midpoint of the cable,so the two male ends can be separated by up to approximately 500mm(19.68"). Black: GND Red?Servo power White?Signal |Applications| RC...

The LSM6DS3 is a accelerometer and gyroscope sensor with a giant 8kb FIFO buffer and embedded processing interrupt functions, specifically targeted at the cellphone market. Due to the capabilities...

The LSM6DS3 is a accelerometer and gyroscope sensor with a giant 8kb FIFO buffer and embedded processing interrupt functions, specifically targeted at the cellphone market. Due to the capabilities and low cost of the LSM6DS3 we've created this small breakout board just for you! Each LSM6DS3 Breakout has been designed to be super-flexible and can be configured specifically for many applications. With the LSM6DS3 Breakout you will be able to detect shocks, tilt, motion, taps, count steps, and...

The SyRen motor driver is one of the most versatile, efficient and easy to use motor drivers on the market. It is suitable for medium powered robots - up to 30lbs in combat or 100lbs for general...

The SyRen motor driver is one of the most versatile, efficient and easy to use motor drivers on the market. It is suitable for medium powered robots - up to 30lbs in combat or 100lbs for general purpose robotics. Out of the box, the SyRen 10 can supply a single DC brushed motor with up to 10A continuously. Peak currents of 15A are achievable for a few seconds. Overcurrent and thermal protection means you'll never have to worry about killing the driver with accidental stalls or by hooking up...

The SyRen motor driver is one of the most versatile, efficient and easy to use motor drivers on the market. It is suitable for medium powered robots - up to 50lbs in combat or 180lbs for general...

The SyRen motor driver is one of the most versatile, efficient and easy to use motor drivers on the market. It is suitable for medium powered robots - up to 50lbs in combat or 180lbs for general purpose robotics. Out of the box, the SyRen 25 can supply a single DC brushed motor with up to 25A continuously. Peak currents of 45A are achievable for a few seconds. Overcurrent and thermal protection means you'll never have to worry about killing the driver with accidental stalls or by hooking up...

The SyRen motor driver is one of the most versatile, efficient and easy to use motor drivers on the market. Out of the box, the SyRen 50 can supply a single DC brushed motor with up to 50A...

The SyRen motor driver is one of the most versatile, efficient and easy to use motor drivers on the market. Out of the box, the SyRen 50 can supply a single DC brushed motor with up to 50A continuously. Peak currents of 100A are achievable for a few seconds. Overcurrent and thermal protection means you'll never have to worry about killing the driver with accidental stalls or by hooking up too big a motor. With just one SyRen driver you can control a motor with: analog voltage, radio control,...

What is a stepper motor? Stepper motor is a brushless DC electric motor that divides a full rotation into a number of equal steps The motor's position can then be commanded to move and hold at one...

What is a stepper motor? Stepper motor is a brushless DC electric motor that divides a full rotation into a number of equal steps The motor's position can then be commanded to move and hold at one of these steps. How to control a stepper motor?The fast way to control a stepper motor is just using a stepper motor driver (controller). And TB6600 arduino is just what you need.TB6600 arduino is an easy-to-use professional stepper motor driver, which could control a two-phase stepping motor. It is...

This is a ultra compact size Dual-H-Bridge dc motor driver (Based on HR8833), which could drive two way 1.5A DC brush motors up to 10V . It has the same footprint as your thumbnail suitable for...

This is a ultra compact size Dual-H-Bridge dc motor driver (Based on HR8833), which could drive two way 1.5A DC brush motors up to 10V . It has the same footprint as your thumbnail suitable for projects with limited spaces. Both sides of the module are desgined with standard XH2.54 pins, which allows you to plug it on a breadboard or prototype board. Caption|Specification| Logic Input Voltage (VCC): 3.3-5V Load Supply Voltage (VM): 3.3-10V Maximum Continuous Operating Current: 1500mA( Single)...

This is a stepper motor driver introduced by DFRobot for those projects require powerful stepper motors, such as a pair of automatic curtains, an XY Plotter. This shield allows Arduino drive stepper...

This is a stepper motor driver introduced by DFRobot for those projects require powerful stepper motors, such as a pair of automatic curtains, an XY Plotter. This shield allows Arduino drive stepper motors (up to 2A per motor coil, 40V max). This stepper motor drive shied adoptes a TMC260 chip which is the first energy efficient high precision microstepping driver IC for bipolar stepper motors with integrated power MOSFETs. The unique high resolution sensorless load detection...

    Tower Pro SG90 is a high quality, low-cost servo for all your mechatronic needs. It comes with a 3-pin power and control cable, mounting hardware. Specification Operating...

    Tower Pro SG90 is a high quality, low-cost servo for all your mechatronic needs. It comes with a 3-pin power and control cable, mounting hardware. Specification Operating Voltage: 4.8 ~ 6.0V Operating Speed: 0.12sec/60 degree(4.8V)~0.1sec/60 degree(6.0V) Torque: 1.6kg/cm(4.8V) Dead Band Width: 5usec Temperature Range: -30?~+60? Cable Length: 25cm Brand name: Tower Pro location of each pin: red (+), brown (-), yellow (signal). ...

The TowerPro SG90C is a 360 degree micro servo. It uses a plastic gear drive and is light and compact. It can be used for various applications and DIY products, such as toy cars, boats, windmills...

The TowerPro SG90C is a 360 degree micro servo. It uses a plastic gear drive and is light and compact. It can be used for various applications and DIY products, such as toy cars, boats, windmills etc. A 360 degree servo’s operation is more similar to a DC motor than a standard servo as only rotation direction and speed can be controlled. There is also no hardware stop inside so that the shaft can rotate freely. Compared to an ordinary DC motor, a 360-degree servo motor does not require...

This is a TT Micro DC Geared Motor with Back Shaft working at 6V with 160rpm. The TT motor series the most popular DC motors for DIY enthusiasts. It is designed to easily incorporate the DFRobot...

This is a TT Micro DC Geared Motor with Back Shaft working at 6V with 160rpm. The TT motor series the most popular DC motors for DIY enthusiasts. It is designed to easily incorporate the DFRobot Encoder. These motors are inexpensive, small, easy to install, and ideally suited for use in a mobile robot. The DFRobot ROMEO microcontroller is able to complete the closed-loop PID making use of the Gravity:TT Motor Encoders Kit. We recommend this rubber wheel for this motor. |Specification|Electrical...

The new Veyron brushless motor controller DFBLDC(1x5A) provides 3 different kinds Input modes(PPM?UART?ANALOG) it is especially designed for brushless motors which are widely used in robotics...

The new Veyron brushless motor controller DFBLDC(1x5A) provides 3 different kinds Input modes(PPM?UART?ANALOG) it is especially designed for brushless motors which are widely used in robotics industry because of their high-performance and good reliability. |Specification| Model Size:74mm X 40mm X 19mm Moedl Weight: 50g Input Voltage: 8~30V(12~24V recommended) Operating Temperature: -30??70? Input modes: PPM?UART?ANALOG?0~5V) Baudrate Types:1200/2400/4800/9600/14400/19200/28800/38400/57600/11520...

Veyron Servo Driver (24-Channel) is a multiple servo controller, especially designed for humanoid robots, spider robots, robotic arms, and many other likewise applications. The controller integrates...

Veyron Servo Driver (24-Channel) is a multiple servo controller, especially designed for humanoid robots, spider robots, robotic arms, and many other likewise applications. The controller integrates wireless data transmission interface, which is fully compatible with DFRobot Bluetooth module, APC220 wireless data transmission module and Xbee module. The controlling modes include real-time, timer and constant speed. Veyron Servo Driver (24-Channel) is the most powerful Mirco USB servo driver...

Wind & Water Power Turbines Description: The Wind & Water Power Turbines convert the wind & water to the mechanical energy and then convert to electricity power. This mini Turbines...

Wind & Water Power Turbines Description: The Wind & Water Power Turbines convert the wind & water to the mechanical energy and then convert to electricity power. This mini Turbines outputs small power for small projects such as LED, suitable for DIY projects. Note that the output of the turbine is AC, Rectifiers are needed if you want to change it into DC. As we tested, the turbines can power 5 LEDs with a wind speed 20 km/h, and 10 LEDs with a wind speed 50 km/h. you can use this...