Robotics

This gearmotor consists of a low-power, 12 V brushed DC motor combined with a 9.68:1 metal spur gearbox, and it has an integrated 48 CPR quadrature encoder on the motor shaft, which provides 464.64...

This gearmotor consists of a low-power, 12 V brushed DC motor combined with a 9.68:1 metal spur gearbox, and it has an integrated 48 CPR quadrature encoder on the motor shaft, which provides 464.64 counts per revolution of the gearbox’s output shaft. The gearmotor is cylindrical, with a diameter just under 25 mm, and the D-shaped output shaft is 4 mm in diameter and extends 12.5 mm from the face plate of the gearbox. A two-channel Hall effect encoder is used to sense the rotation of a magnetic...

These micro gearmotors are incredibly tough and feature full metal gears. They have a gear ratio of 150:1 and operate up to 12 volts and have a stall torque of 45 oz-in. and a max speed of 175 RPM....

These micro gearmotors are incredibly tough and feature full metal gears. They have a gear ratio of 150:1 and operate up to 12 volts and have a stall torque of 45 oz-in. and a max speed of 175 RPM. Each micro gearmotor sports a 3mm D-shaft. Note: The micro gearmotor enclosures are sold separately, you can find them here. Features: Voltage: 6 - 12 Volts Gear Ratio: 150:1 Stall Torque: 17/45 oz-in. (6/12V) Speed: 90/175 RPM (6/12V) No Load Current: 40/70 mA (6/12V) Stall Current: 360/1600 mA...

These micro gearmotors are incredibly tough and feature full metal gears. They have a gear ratio of 50:1 and operate up to 12 volts and have a stall torque of 20 oz-in. and a max speed of 460 RPM....

These micro gearmotors are incredibly tough and feature full metal gears. They have a gear ratio of 50:1 and operate up to 12 volts and have a stall torque of 20 oz-in. and a max speed of 460 RPM. Each micro gearmotor sports a 3mm D-shaft. Note: The micro gearmotor enclosures are sold separately, you can find them here. Features: Voltage: 6 - 12 Volts Gear Ratio: 50:1 Stall Torque: 7/20 oz-in. (6/12V) Speed: 240/460 RPM (6/12V) No Load Current: 40/100 mA (6/12V) Stall Current: 360/1600 mA...

These micro gearmotors are incredibly tough and feature full metal gears. They have a gear ratio of 298:1 and operate up to 12 volts and have a stall torque of 70 oz-in. and a max speed of 90 RPM....

These micro gearmotors are incredibly tough and feature full metal gears. They have a gear ratio of 298:1 and operate up to 12 volts and have a stall torque of 70 oz-in. and a max speed of 90 RPM. Each micro gearmotor sports a 3mm D-shaft. Note: The micro gearmotor enclosures are sold separately, you can find them here. Features: Voltage: 6 - 12 Volts Gear Ratio: 298:1 Stall Torque: 40/70 oz-in. (6/12V) Speed: 45/90 RPM (6/12V) No Load Current: 30/70 mA (6/12V) Stall Current: 360/1600 mA...

These micro gearmotors are incredibly tough and feature full metal gears. They have a gear ratio of 30:1 and operate up to 12 volts and have a stall torque of 9 oz-in. and a max speed of 900 RPM....

These micro gearmotors are incredibly tough and feature full metal gears. They have a gear ratio of 30:1 and operate up to 12 volts and have a stall torque of 9 oz-in. and a max speed of 900 RPM. Each micro gearmotor sports a 3mm D-shaft. Note: The micro gearmotor enclosures are sold separately, you can find them here. Features: Voltage: 6 - 12 Volts Gear Ratio: 30:1 Stall Torque: 4/9 oz-in. (6/12V) Speed: 450/900 RPM (6/12V) No Load Current: 40/120 mA (6/12V) Stall Current: 360/1600 mA...

These enclosures allow you to mount your micro gearmotor to other Actobotics products easily. Once your gearmotor is inserted, you can take advantage of the 0.77” hole pattern. These enclosures have...

These enclosures allow you to mount your micro gearmotor to other Actobotics products easily. Once your gearmotor is inserted, you can take advantage of the 0.77” hole pattern. These enclosures have a length of 1.14”, a width of 1”, and a thickness of 0.50”. Actobotics is a robotics building system based around extruded aluminum channels, gears, precision shafts, and ball bearings. Thanks to the two standardized hole patterns, nearly all Actobotics components can be intuitively connected...

This is the Micro Gripper Kit A, a simple robotics kit that is great for "getting a grip" on smaller robotics projects! Designed for use with a servo, the gripper kit is easy to assemble and...

This is the Micro Gripper Kit A, a simple robotics kit that is great for "getting a grip" on smaller robotics projects! Designed for use with a servo, the gripper kit is easy to assemble and requires only a Phillips Head Screwdriver. This Micro Gripper is capable of opening 2.75" wide max, has an overall body length of 1.7" long with a 1.3" wide servo housing body, and offers three 6-32 mounting through-holes along the edges of the servo housing. Actobotics is a robotics building system based...

This is the Micro Gripper Kit B, a simple robotics kit that is great for "getting a grip" on smaller robotics projects! Designed for use with any sub-micro size Hitec servo, the gripper kit is easy...

This is the Micro Gripper Kit B, a simple robotics kit that is great for "getting a grip" on smaller robotics projects! Designed for use with any sub-micro size Hitec servo, the gripper kit is easy to assemble and requires only a Phillips Head Screwdriver. This Micro Gripper is capable of opening 2.75" wide max, has an overall body dimension of 2.6" long by 1.3" wide, and offers the 0.77" hub pattern for easy mounting on Actobotics components. Actobotics is a robotics building system based...

This is a 5-pack of the M.2 screws that SparkFun uses with the MicroMod ecosystem. MicroMod uses the common M.2 connector. This is the same connector found on modern motherboards and laptops. There...

This is a 5-pack of the M.2 screws that SparkFun uses with the MicroMod ecosystem. MicroMod uses the common M.2 connector. This is the same connector found on modern motherboards and laptops. There are various locations for the plastic ‘key’ on the M.2 connector to prevent a user from inserting an incompatible device. The MicroMod standard uses the ‘E’ key and further modifies the M.2 standard by moving the mounting screw 4mm to the side. The ‘E’ key is fairly common so a user could insert a...

This custom-designed rubber wheel has a rubber tire with a diameter of 1.69" (43 mm). It is designed to fit the output shafts on our mini metal gear motors as well as the Solarbotics metal gear...

This custom-designed rubber wheel has a rubber tire with a diameter of 1.69" (43 mm). It is designed to fit the output shafts on our mini metal gear motors as well as the Solarbotics metal gear motors. Teeth on the hub optionally allow a reflectance sensor to be used for encoder feedback.Gear motors should be mounted onto the side of the hub with the protruding teeth. The output shaft will slide into the socket easily at first but will achieve a snug fit when pressed through to the other edge...

Description: These are standard nuts with 2-56 thread. For use with 2-56 machine screws and five button pad set listed below. Sold in single units.

Description: These are standard nuts with 2-56 thread. For use with 2-56 machine screws and five button pad set listed below. Sold in single units.

We could talk about how the Zinc used in these nuts is only from the finest old-growth Zinc trees from across the globe and is hand picked only at the peak of the season. Or how they are expertly...

We could talk about how the Zinc used in these nuts is only from the finest old-growth Zinc trees from across the globe and is hand picked only at the peak of the season. Or how they are expertly hand-ground by a 6th generation master grinder. And how every nut passes a rigorous 19-point inspection process at each step of the process. And how each nut's dimensional variations can only be measured on the sub-atomic level. We could say all that, but it would be a lie. These are standard 4-40...

Give your robot some traction with this 2-pack of rubber O-rings. Measuring 55mm outer diameter, 45mm inner diameter, and 5mm wire diameter, they provide a reliable and versatile solution for a...

Give your robot some traction with this 2-pack of rubber O-rings. Measuring 55mm outer diameter, 45mm inner diameter, and 5mm wire diameter, they provide a reliable and versatile solution for a two-wheel robotics platform. Note: These are the same o-rings used with the XRP kits Beta & DIY Includes: 2x Rubber O-Ring Features: Outer Diameter: 55mm Inner Diameter: 45mm Wire Diameter: 5mm Documents: Drawing ...

This pan/tilt bracket consists of two brackets and all the hardware you need to attach them to make a pan/tilt mechanism using two servo motors. We recommend our small servo motors listed below....

This pan/tilt bracket consists of two brackets and all the hardware you need to attach them to make a pan/tilt mechanism using two servo motors. We recommend our small servo motors listed below. Note: Servos are not included. The sub-micro servo size works for these mounts. Documents: Dimensional Drawing Assembly Guide Face Tracking Tutorial Videos ...

This is an easy-to-assemble pan/tilt bracket kit that utilizes servos to move on two axes fit for camera and helping-hand applications. This particular bracket kit is the same one we use in our...

This is an easy-to-assemble pan/tilt bracket kit that utilizes servos to move on two axes fit for camera and helping-hand applications. This particular bracket kit is the same one we use in our SparkFun Raspberry Pi Zero W Camera Kit to create a remote camera system for your home or workplace. Everything is included to get this kit assembled, even the servos (just be sure the servo motors are centered during assembly). All you will need is a small screwdriver set and a pair of clippers. Note:...

The Pixhawk® 6C is the latest update to the successful family of Pixhawk® flight controllers, based on the Pixhawk® FMUv6C Open Standard and Connector Standard. It comes with PX4 Autopilot®...

The Pixhawk® 6C is the latest update to the successful family of Pixhawk® flight controllers, based on the Pixhawk® FMUv6C Open Standard and Connector Standard. It comes with PX4 Autopilot® pre-installed. Inside the Pixhawk® 6C, you can find an STMicroelectronics® based STM32H743, paired with sensor technology from Bosch® & InvenSense®, giving you flexibility and reliability for controlling any autonomous vehicle, suitable for both academic and commercial applications. The Pixhawk® 6C's H7...

The Pixhawk® 6C with M8N GPS is the latest update to the successful family of Pixhawk® flight controllers, based on the Pixhawk® FMUv6C Open Standard and Connector Standard. It comes with PX4...

The Pixhawk® 6C with M8N GPS is the latest update to the successful family of Pixhawk® flight controllers, based on the Pixhawk® FMUv6C Open Standard and Connector Standard. It comes with PX4 Autopilot® pre-installed. Inside the Pixhawk® 6C, you can find an STMicroelectronics® based STM32H743, paired with sensor technology from Bosch® & InvenSense®, giving you flexibility and reliability for controlling any autonomous vehicle, suitable for both academic and commercial applications. The...

The Pixhawk® 6C is the latest update to the successful family of Pixhawk® flight controllers, based on the Pixhawk® FMUv6C Open Standard and Connector Standard. It comes with PX4 Autopilot®...

The Pixhawk® 6C is the latest update to the successful family of Pixhawk® flight controllers, based on the Pixhawk® FMUv6C Open Standard and Connector Standard. It comes with PX4 Autopilot® pre-installed. Inside the Pixhawk® 6C, you can find an STMicroelectronics® based STM32H743, paired with sensor technology from Bosch® & InvenSense®, giving you flexibility and reliability for controlling any autonomous vehicle, suitable for both academic and commercial applications. The Pixhawk® 6C's H7...

The Pixhawk® 6C with M8N GPS is the latest update to the successful family of Pixhawk® flight controllers, based on the Pixhawk® FMUv6C Open Standard and Connector Standard. It comes with PX4...

The Pixhawk® 6C with M8N GPS is the latest update to the successful family of Pixhawk® flight controllers, based on the Pixhawk® FMUv6C Open Standard and Connector Standard. It comes with PX4 Autopilot® pre-installed. Inside the Pixhawk® 6C, you can find an STMicroelectronics® based STM32H743, paired with sensor technology from Bosch® & InvenSense®, giving you flexibility and reliability for controlling any autonomous vehicle, suitable for both academic and commercial applications. The...

This is a simple ~140RPM (no load), DC planetary gearmotor. This motor is great for various applications such as robotics, electric locks, household automation, and small actuators. The supply...

This is a simple ~140RPM (no load), DC planetary gearmotor. This motor is great for various applications such as robotics, electric locks, household automation, and small actuators. The supply voltage range is 6VDC - 24VDC with the polarity marker at the base of the motor. The planetary gear box, mounted on top of the motor housing, gives this motor a relatively large stall torque for its size. The overall body of the motor is made of metal, with the exception of the set of planet gears on the...

Qwiic Boost increases the Qwiic bus from 3.3V to 5V while still providing the target device with 3.3V I2C signals. This is a handy board for connecting technologies that still require 5V for running...

Qwiic Boost increases the Qwiic bus from 3.3V to 5V while still providing the target device with 3.3V I2C signals. This is a handy board for connecting technologies that still require 5V for running higher voltage mechanisms (like a DC fan) but have an internal processor running at 3.3V. We've seen this a lot with air quality sensors that use a fan to push air into a test chamber. The 5V boost circuit is rated up to 100mA with 90% efficiency. For applications where the 5V device needs 5V I2C...

With a clear view of the sky, the Qwiic Iridium 9603 allows you to send and receive short messages. It works anywhere in the world, far beyond the reach of WiFi and GSM networks. Maybe you want to...

With a clear view of the sky, the Qwiic Iridium 9603 allows you to send and receive short messages. It works anywhere in the world, far beyond the reach of WiFi and GSM networks. Maybe you want to transmit weather information from a weather station on top of a mountain? Or use it to send data from a travelling balloon sat? Perhaps you need to communicate in an emergency, when other networks might not be available? At the heart of our product is an Iridium 9603 modem. The Qwiic module hosts the...

The RC Air Mouse and Keyboard uses the latest 2.4GHz wireless technology with a sampling frequency up to 120Hz. Use it like a Wii remote to control your mouse cursor on the screen. Operation is...

The RC Air Mouse and Keyboard uses the latest 2.4GHz wireless technology with a sampling frequency up to 120Hz. Use it like a Wii remote to control your mouse cursor on the screen. Operation is flexible and smooth and does no connection is lost during rapid movement.The RC Air Mouse and Keyboard can be used for a wide range of devices and drivers install automatically when you plug it in. With a wide transmission range of up to 30m, you can use this remote control your computer in style. Sit...

This is a 2 DOF robot gripper that can be installed with 2 servos so as to control gripper opening and closing with one servo, and steering gear motion control (or rotation) with the other...

This is a 2 DOF robot gripper that can be installed with 2 servos so as to control gripper opening and closing with one servo, and steering gear motion control (or rotation) with the other servo.Velocity range is 0 to 54 mm (0 to 2.13"). Total weight about 45 g. The servo slot fit most servos such as Hitec 422,475, DSS-P05 Standard Servo, DF Metal Geared 15Kg Standard Servo. |Specification| Clamp range:0-54mm (0-2.13") Size:105x100x30mm (4.13x3.94x1.18")|ShippingList| Robot Gripper-Extra Width...

Does your robot crush objects with its hulkishly strong grip? Give your robotic hand or claw a better sense of touch with the Robotic Finger Sensor. This new version adds pressure sensing so now you...

Does your robot crush objects with its hulkishly strong grip? Give your robotic hand or claw a better sense of touch with the Robotic Finger Sensor. This new version adds pressure sensing so now you can know how hard you're gripping! The Robotic Finger Sensor (RFS) uses a unique combination of infrared distance sensing, pressure sensing, optical encapsulant, and data filtering to detect extremely light touches. Additionally, the silicon covering is squishy, giving the sensor increased grip...

Romeo BLE Quad is an arduino compatible robot controller based on STM32 ARM chip. It inherits all features from the Bluno M3, including wireless programming support, wireless communication between...

Romeo BLE Quad is an arduino compatible robot controller based on STM32 ARM chip. It inherits all features from the Bluno M3, including wireless programming support, wireless communication between iOS/Android apps and remote control. Beyond this it also includes a 4-way DC motor driver and encoder interfaces. You can implement a robot with PID closed-loop feedback control directly with our TT Geared Motor.As well as this the Romeo BLE Quad offers powerful performance thanks to the STM32 ARM...

Rover 5 is a new breed of tracked robot chassis designed specifically for students and hobbyist. Unlike conventional tracked chassis&;rsquo;s the clearance can be adjusted by rotating the gearboxes...

Rover 5 is a new breed of tracked robot chassis designed specifically for students and hobbyist. Unlike conventional tracked chassis&;rsquo;s the clearance can be adjusted by rotating the gearboxes in 5-degree increments. &;ldquo;Stretchy&;rdquo; rubber treads maintain tension as the clearance is raised.Inside of the chassis are 4 noise suppression coils at the bottom and a battery holder that accepts 6x AA batteries (not included). It is recommended to use NiMh batteries as they last longer...

Rover 5 is a new breed of tracked robot chassis designed specifically for students and hobbyist. Unlike conventional tracked chassis’s the clearance can be adjusted by rotating the gearboxes...

Rover 5 is a new breed of tracked robot chassis designed specifically for students and hobbyist. Unlike conventional tracked chassis’s the clearance can be adjusted by rotating the gearboxes in 5-degree increments. “Stretchy” rubber treads maintain tension as the clearance is raised.Inside of the chassis are 4 noise suppression coils at the bottom and a battery holder that accepts 6x AA batteries (not included). It is recommended to use NiMh batteries as they last longer and...

This rubber wheel is used in our popular 4WD mobile platforms. It can be mounted directly onto micro gear motors, but also compatible with our most servos.|Specification| Outer Diameter: 80mm(3.15")...

This rubber wheel is used in our popular 4WD mobile platforms. It can be mounted directly onto micro gear motors, but also compatible with our most servos.|Specification| Outer Diameter: 80mm(3.15") Wheel Width:30 mm(1.18") Axle Pore Size: 5.8mm(diameter)×3.5mm?thickness? (0.23"x0.14") Axle depth:7.6mm(0.30")|ShippingList| Rubber Wheel(Compatible with Servo&Motor) x2 ...

These are Philips-head M3 screws. They are 12mm long and come in packs of three. This is the screw size that the MiP robotic Platform and its add-on boards uses. Check below for the associated...

These are Philips-head M3 screws. They are 12mm long and come in packs of three. This is the screw size that the MiP robotic Platform and its add-on boards uses. Check below for the associated hardware.

Standard Philips-head 4-40 screws. They are 1/2" long and come in packs of ten. This is the screw size we use in most of the holes for our breakout boards. Check below for other associated hardware. ...

Standard Philips-head 4-40 screws. They are 1/2" long and come in packs of ten. This is the screw size we use in most of the holes for our breakout boards. Check below for other associated hardware.

There are your standard Philips-head 4-40 screws. They are 1/4" long and come in packs of ten. This is the screw size we use in most of the holes for our breakout boards. Check below for other...

There are your standard Philips-head 4-40 screws. They are 1/4" long and come in packs of ten. This is the screw size we use in most of the holes for our breakout boards. Check below for other associated hardware.

These are standard screws with 2-56 thread and 3/8" long, recommended for the small button pad sets. Can be used with a 2-56 nut. Sold in single units.

These are standard screws with 2-56 thread and 3/8" long, recommended for the small button pad sets. Can be used with a 2-56 nut. Sold in single units.

Serial flash chips are everywhere and they're as useful as they are ubiquitous. If you've never used a serial flash device in your own projects, you should try it, because it's very handy to have a...

Serial flash chips are everywhere and they're as useful as they are ubiquitous. If you've never used a serial flash device in your own projects, you should try it, because it's very handy to have a place to store things that don't fit in program memory. Things like sensor readings, long strings, and error logs can be hard to stow away on platforms that don't have a ton of in-built storage, which is where serial flash comes in. Simply write all of that data out over SPI for the flash chip to...

Here is a simple, low-cost, high quality servo for all your mechatronic needs. This servo is very similar in size and specifications to the Hitec HS-55. This little guy is able to take in 6 volts...

Here is a simple, low-cost, high quality servo for all your mechatronic needs. This servo is very similar in size and specifications to the Hitec HS-55. This little guy is able to take in 6 volts and deliver 20.8 oz-in. of maximum torque at 0.10 sec/60° This small servo comes with a standard 3 pin power and control cable, and all hardware listed below. Note: This servo is rated for 180° rotation, but in actuality it only hits ~160°. Includes: 1x Micro Size Servo 1x Single Arm Micro Horn 1x...

Here, for all your mechatronic needs, is a simple, high quality continuous rotation servo motor. This servo is able to take in 6 volts and deliver 30.6 oz-in. of maximum torque at 0.14 sec/60° A...

Here, for all your mechatronic needs, is a simple, high quality continuous rotation servo motor. This servo is able to take in 6 volts and deliver 30.6 oz-in. of maximum torque at 0.14 sec/60° A standard 3-pin power and control cable is attached and all hardware listed below is included. Includes: 1x SM-S3317S Full Rotation Servo 1x Single Arm Horn 1x Double Arm Horn 1x Four Point Horn 4x Rubber Grommets 4x 2x15mm Phillips Screw 4x Brass Eyelets Features: Voltage: 4.8-6.0 Volts Torque:...

Here is a powerful, low-cost, reliable servo for all your mechatronic needs. This servo is able to take in 6 volts and deliver 83.47 oz-in. of maximum torque at 0.16 sec/60° This is a tough little...

Here is a powerful, low-cost, reliable servo for all your mechatronic needs. This servo is able to take in 6 volts and deliver 83.47 oz-in. of maximum torque at 0.16 sec/60° This is a tough little servo with a standard 3 pin power and control cable, and all hardware listed below. Replaces:ROB-9064 Includes: 1x FS5106B High Torque Servo 1x Double Arm Horn 1x Circle Horn 1x Four Point Horn 1x Six Point Horn 2x 3x10mm Phillips Screw 4x 2x13mm Mounting Phillips Screw 4x Rubber Grommets 4x Brass...

Here, for all your mechatronic needs, is a simple, high quality continuous rotation servo motor. This servo is able to take in 6 volts and deliver 66.7 oz-in. of maximum torque at 70 r/min. A...

Here, for all your mechatronic needs, is a simple, high quality continuous rotation servo motor. This servo is able to take in 6 volts and deliver 66.7 oz-in. of maximum torque at 70 r/min. A standard 3-pin power and control cable is attached and all hardware listed below is included. Includes: 1x SM-S4303R High Torque Continuous Rotation Servo 1x Mounting Screw 1x Four Point Horn 1x Six Point Horn 2x Double Arm Horn (1x Large, 1x Medium) 2x Circle Horn (1x Large, 1x Medium) 4x Rubber...

Here is a simple, low-cost, high quality servo for all your mechatronic needs. This servo is able to take in 6 volts and deliver 44.4 oz-in. of maximum torque at 0.18 sec/60° This is a small servo...

Here is a simple, low-cost, high quality servo for all your mechatronic needs. This servo is able to take in 6 volts and deliver 44.4 oz-in. of maximum torque at 0.18 sec/60° This is a small servo with a standard 3 pin power and control cable (red = power, brown = ground, and yellow = data), and all hardware listed below. Features: Voltage: 4.8-6.0 Volts Torque: 38.8/44.4 oz-in. (4.8/6.0V) Speed: 0.20/0.18 sec/60° (4.8/6.0V) Rotation: 160° Dual Ball Bearing Metal Gears* 28.8 x 13.8 x...

This is the classic Hitec HS-422 servo. This solid consumer grade servo is able to take in 6 volts and deliver 57 oz-in. of maximum torque at 0.16 sec/60°, this is a simple servo for any beginner...

This is the classic Hitec HS-422 servo. This solid consumer grade servo is able to take in 6 volts and deliver 57 oz-in. of maximum torque at 0.16 sec/60°, this is a simple servo for any beginner project! This high quality servo is perfect for your mechatronic needs and if you are looking to get into robotics, this is where to start. The HS-422 servo comes standard with a 3-pin power and control cable and all hardware listed below. Includes: 1x HS-422 Servo 1x Circle Horn 1x Double Arm Horn 1x...

This is the versatile Hitec HS-425BB servo. This little guy is able to take in 6 volts and deliver 57 oz-in. of maximum torque at 0.16sec/60°, this is a great servo even if you are on a budget! This...

This is the versatile Hitec HS-425BB servo. This little guy is able to take in 6 volts and deliver 57 oz-in. of maximum torque at 0.16sec/60°, this is a great servo even if you are on a budget! This high quality servo is perfect for your mechatronic needs and if you are looking to get into robotics, this is where to start. The HS-425BB servo comes standard with a 3-pin power and control cable and all hardware listed below. Includes: 1x HS-425BB Servo 1x Circle Horn 1x Double Arm Horn 1x Single...

This beast is the Hitec HS-805BB servo. Able to take in 6 volts and deliver an impressive 343 oz-in. of maximum torque at 0.14 sec/60°, this is a heavy duty servo and is not to be taken lightly!...

This beast is the Hitec HS-805BB servo. Able to take in 6 volts and deliver an impressive 343 oz-in. of maximum torque at 0.14 sec/60°, this is a heavy duty servo and is not to be taken lightly! This high quality servo is perfect for your mechatronic needs and if you are looking to get into robotics, this is where to start. The HS-805BB servo comes standard with a 3-pin power and control cable, Y-harness, and all hardware listed below. Note: This servo can draw around 800mA, so keep that in...

This is the epitome of the phrase "appearances can be deceiving," and trust us, with the Hitec HS-85MG that couldn't be more true. The HS-85MG is able to take in 6 volts and deliver 49 oz-in. of...

This is the epitome of the phrase "appearances can be deceiving," and trust us, with the Hitec HS-85MG that couldn't be more true. The HS-85MG is able to take in 6 volts and deliver 49 oz-in. of maximum torque at 0.14sec/60°, and this guy is only about the size of a bottle cap! This high quality servo is perfect for your mechatronic needs and if you are looking to get into robotics, this is where to start. The HS-85MG servo comes standard with a 3-pin power and control cable and all hardware...

The Shadow Chassis is a marvelously durable and modular robot platform from RobotZone. The chassis plates and mounts are cut from ABS plastic and utilize the Actobotics 0.77" and 1.50" hub patterns...

The Shadow Chassis is a marvelously durable and modular robot platform from RobotZone. The chassis plates and mounts are cut from ABS plastic and utilize the Actobotics 0.77" and 1.50" hub patterns for sensors, controllers, power, etc. Simply snap each panel together and you'll be able to attach your motors and favorite robotics controller. With the included "snap on” micro-controller mounts, you can attach an Arduino, Raspberry Pi, SparkFun RedBoard, or SparkFun RedBot Mainboard! This kit...

These plastic shaft spacers have an inner diameter of 1/2” and a thickness of 1/16”. These spacers are ideal for spacing out an area between a bearing and a shaft collar to reduce metal to metal...

These plastic shaft spacers have an inner diameter of 1/2” and a thickness of 1/16”. These spacers are ideal for spacing out an area between a bearing and a shaft collar to reduce metal to metal contact. Features: ID - 1/2" Width - 1/16”

These plastic shaft spacers have an inner diameter of 5/8” and a thickness of 1/16”. These spacers are ideal for spacing out an area between a bearing and a shaft collar to reduce metal to metal...

These plastic shaft spacers have an inner diameter of 5/8” and a thickness of 1/16”. These spacers are ideal for spacing out an area between a bearing and a shaft collar to reduce metal to metal contact. Features: ID - 5/8" Width - 1/16”

Protect your board or project with this four pack of silicone bumpers! Rubber feet raise your PCB or project up off your desk. This helps prevent short circuiting from bits of scrap wire floating...

Protect your board or project with this four pack of silicone bumpers! Rubber feet raise your PCB or project up off your desk. This helps prevent short circuiting from bits of scrap wire floating about or setting a project down on a conductive surface. They also prevent your enclosure or PCB from sliding around. They can also be used as feet for enclosures. Includes: 4x Silicone Bumpers

Rubber feet raise your PCB or project up off your desk. This helps prevent short circuiting from bits of scrap wire floating about or setting a project down on a conductive surface. They also...

Rubber feet raise your PCB or project up off your desk. This helps prevent short circuiting from bits of scrap wire floating about or setting a project down on a conductive surface. They also prevent your enclosure or PCB from sliding around. They can also be used as feet for enclosures. These are self-adhesive and 16.5mm in diameter and about 10mm tall. They taper to roughly 12mm at the top. They come in a set of 4.

These skate wheel adaptors have a diameter of 1”, a width of 0.32”, and utilize the 0.77” hub pattern. These adaptors allow you to attach the 2.975” or 4.90” skate wheels to ¼” drive shafts....

These skate wheel adaptors have a diameter of 1”, a width of 0.32”, and utilize the 0.77” hub pattern. These adaptors allow you to attach the 2.975” or 4.90” skate wheels to ¼” drive shafts. Actobotics is a robotics building system based around extruded aluminum channels, gears, precision shafts, and ball bearings. Thanks to the two standardized hole patterns, nearly all Actobotics components can be intuitively connected together. The wide range of components makes building complex...

This is a 12 wire slip ring, a remarkably simple electromechanical assembly that allows electronic signals to be passed through its rotating innards. Commonly, you'd find slip rings in wind...

This is a 12 wire slip ring, a remarkably simple electromechanical assembly that allows electronic signals to be passed through its rotating innards. Commonly, you'd find slip rings in wind turbines, radar antennae, or anything else that requires continuous 360° rotation while maintaining an electrical connection. This particular slip ring provides you with a compact body with gold-on-gold alloy fiber brush to plated ring contacts inside. Each Slip ring is capable of handling a continuous...

This is a 3 wire slip ring, a remarkably simple electromechanical assembly that allows for electronic signals and power to be passed through its rotating innards. Commonly, you'd find slip rings in...

This is a 3 wire slip ring, a remarkably simple electromechanical assembly that allows for electronic signals and power to be passed through its rotating innards. Commonly, you'd find slip rings in wind turbines, radar antennae, or anything else that requires continuous 360° rotation while maintaining an electrical connection. This particular slip ring provides you with a compact body with precious metal alloy fiber brush to silver plated ring contacts inside. We like using these slip rings to...

This is a 6 wire slip ring, a remarkably simple electromechanical assembly that allows electronic signals to be passed through its rotating innards. Commonly, you'd find slip rings in wind turbines,...

This is a 6 wire slip ring, a remarkably simple electromechanical assembly that allows electronic signals to be passed through its rotating innards. Commonly, you'd find slip rings in wind turbines, radar antennae, or anything else that requires continuous 360° rotation while maintaining an electrical connection. This particular slip ring provides you with a compact body with gold-on-gold alloy fiber brush to plated ring contacts inside. Each Slip ring is capable of handling a continuous...

These small steppers are a great way to get things moving, especially when positioning and repeatability is a concern. When using a current limiting driver such as the Easydriver or Big Easydriver,...

These small steppers are a great way to get things moving, especially when positioning and repeatability is a concern. When using a current limiting driver such as the Easydriver or Big Easydriver, a 12 volt power supply can be used as long as you adjust the current level to 400mA or less. If using a non current limited driver (like a L293D or an H-bridge) you will need to lower your input voltage to keep the motor current below 400mA. This is a Bipolar motor. Features: Stride Angle (degrees)...

This is the 100mm 16-way 0.5mm-pitch Flexible Printed Circuit used to interconnect smôl boards end to end. smôl is an ecosystem of miniature processor boards, peripheral boards, power boards and...

This is the 100mm 16-way 0.5mm-pitch Flexible Printed Circuit used to interconnect smôl boards end to end. smôl is an ecosystem of miniature processor boards, peripheral boards, power boards and accessories. Designed to be both physically small and to have the smallest possible current draw, smôl is the perfect choice for applications like wildlife tracking or discrete long-term monitoring. smôl boards are designed to stack one on top of the other, using 16-way 0.5mm-pitch Flexible Printed...

This is the 36mm 16-way 0.5mm-pitch Flexible Printed Circuit used to interconnect smôl boards side by side. This FPC has an offset (step) of 18mm. smôl is an ecosystem of miniature processor boards,...

This is the 36mm 16-way 0.5mm-pitch Flexible Printed Circuit used to interconnect smôl boards side by side. This FPC has an offset (step) of 18mm. smôl is an ecosystem of miniature processor boards, peripheral boards, power boards and accessories. Designed to be both physically small and to have the smallest possible current draw, smôl is the perfect choice for applications like wildlife tracking or discrete long-term monitoring. smôl boards are designed to stack one on top of the other, using...

The Soft Power Switch is a passive, hard on/off switch with software feedback and control. In other words, it's like the on/off switch on a laptop. A simple press will turn the system on. Another...

The Soft Power Switch is a passive, hard on/off switch with software feedback and control. In other words, it's like the on/off switch on a laptop. A simple press will turn the system on. Another press can (with MCU intervention) turn off the system. And if things go really wrong, pressing and holding the button will force a power-down. If you're building something with an enclosed battery and need a good power button, this is the board you need. The Sense/Control pin can act as an output to a...

Does controlling door and cabinet access with the power of Electromagnetism interest you? Excellent! In effect, this latch / lock solenoid is an electronic lock. When powered with 12VDC source, the...

Does controlling door and cabinet access with the power of Electromagnetism interest you? Excellent! In effect, this latch / lock solenoid is an electronic lock. When powered with 12VDC source, the latch is pulled in, allowing movement. Without power, the latch is extended, blocking movement and your secret drawer is safe and secure. This Solenoid Latch comes with a mounting bracket which can be removed with two screws. Once removed the solenoid can be rotated 180 and remounted. Paired with a...

Solenoids are a great way to induce linear motion for pushing, pulling or controlling switches and levers. According to the datasheet this solenoid is rated for 36V but they work like a charm at...

Solenoids are a great way to induce linear motion for pushing, pulling or controlling switches and levers. According to the datasheet this solenoid is rated for 36V but they work like a charm at 12V. We've been controlling them with the Arduino Power Driver Shield, there's even some example code below. With a throw of 10mm these solenoids are great for all kinds of motion applications such as actuating door latches, automating percussion instruments or just poking people. At 12 volts these...

Solenoids are a great way to induce linear motion for pushing, pulling or controlling switches and levers. This smaller solenoid is designed to work directly with 5V which makes it a great match for...

Solenoids are a great way to induce linear motion for pushing, pulling or controlling switches and levers. This smaller solenoid is designed to work directly with 5V which makes it a great match for embedded projects. It has a throw of about 4.5mm and 2 M2 mounting holes on the body. The wire lead is about 2" long and is terminated with a 2-pin JST PH connector. Note: The mounting holes on this solenoid are actually 1.6mm in diameter. This will allow you to tap for an M2 screw. Also, although...

"This is a motor shield for Arduino that will control two DC motors. Based on the L298 H-bridge, the SparkFun Ardumoto can drive up to 2 amps per channel. The board takes its power from the same Vin...

"This is a motor shield for Arduino that will control two DC motors. Based on the L298 H-bridge, the SparkFun Ardumoto can drive up to 2 amps per channel. The board takes its power from the same Vin line as the Arduino board, includes blue and yellow LEDs to indicate active direction, and all driver lines are diode protected from back EMF. The new version of this shield allows for either 3.3 or 5v logic, a separate and more robust VIN connection, and the PWM input has moved to pin 3. Control...

Robots are fun, and Arduinos are easy. So wouldn't it be nice if there were a kit that included everything you need to get your Arduino device set up to control a simple two-motor-circuit buddy? The...

Robots are fun, and Arduinos are easy. So wouldn't it be nice if there were a kit that included everything you need to get your Arduino device set up to control a simple two-motor-circuit buddy? The SparkFun Ardumoto Shield Kit is perfect for any robot enthusiast and includes an Ardumoto Shield, as well as pairs of tires, motors, connectors and wires. And, of course, it’s all stuffed in a classic SparkFun red box (which may come in handy as a robot chassis). The Ardumoto Shield is an...

The SparkFun 3-Phase Brushless Motor Driver, featuring the TMC6300 from ADI + Trinamic, is a powerful and easy-to-use three-phase motor driver that was designed to control our Brushless Gimbal...

The SparkFun 3-Phase Brushless Motor Driver, featuring the TMC6300 from ADI + Trinamic, is a powerful and easy-to-use three-phase motor driver that was designed to control our Brushless Gimbal Motor. It can be used to control any 3-phase BLDC or PMSM motor with up to 2A (1.4ARMS) of total drive current. Separate high-side and low-side control of the three half-bridges allows for incredible control of each phase of the motor commutation. The driver also provides temperature and short circuit...

This is a breakout board for the L298N full-bridge dual motor driver; which comes in a staggered, Multiwatt package. All pins of the L298N are broken out to a 15-pin 0.1" pitch header. Two mounting...

This is a breakout board for the L298N full-bridge dual motor driver; which comes in a staggered, Multiwatt package. All pins of the L298N are broken out to a 15-pin 0.1" pitch header. Two mounting holes are also provided. Features: Board: 1.6x0.85 inches Documents: Schematic Eagle Files Datasheet (L298N) GitHub (Design Files) ...

Ready to add some good vibes to your project? Look no further than the SparkFun Haptic Motor Driver. This board breaks out Texas Instruments' DRV2605L Haptic Motor Driver, which adds meaningful...

Ready to add some good vibes to your project? Look no further than the SparkFun Haptic Motor Driver. This board breaks out Texas Instruments' DRV2605L Haptic Motor Driver, which adds meaningful feedback from your devices using the breakout and an Arduino-compatible device. The DRV2605L is capable of driving two different types of motors, ERM and LRA. It is important to know, however, that the default firmware for the DRV2605L is set for use with ERM-type motors. We have created an Arduino...