Robotics

These nylon standoffs are 3/8" long and tapped for a 4-40 screw. These are great for mounting your board in an enclosure, or just getting it up off the table. Each standoff has an outer diameter of...

These nylon standoffs are 3/8" long and tapped for a 4-40 screw. These are great for mounting your board in an enclosure, or just getting it up off the table. Each standoff has an outer diameter of 6mm. Sold in packs of 10. Check below for matching screws.

This beast is the Hitec HS-805BB servo. Able to take in 6 volts and deliver an impressive 343 oz-in. of maximum torque at 0.14 sec/60°, this is a heavy duty servo and is not to be taken lightly!...

This beast is the Hitec HS-805BB servo. Able to take in 6 volts and deliver an impressive 343 oz-in. of maximum torque at 0.14 sec/60°, this is a heavy duty servo and is not to be taken lightly! This high quality servo is perfect for your mechatronic needs and if you are looking to get into robotics, this is where to start. The HS-805BB servo comes standard with a 3-pin power and control cable, Y-harness, and all hardware listed below. Note: This servo can draw around 800mA, so keep that in...

These nylon standoffs are 3/8" long and tapped for a 4-40 screw. These are great for mounting your board in an enclosure, or just getting it up off the table. The black nylon will give your project...

These nylon standoffs are 3/8" long and tapped for a 4-40 screw. These are great for mounting your board in an enclosure, or just getting it up off the table. The black nylon will give your project a very sessy look. Sold in packs of 10. Check below for matching screws.

The DG01D-E is a single hobby motor with a hall speed encoder. This motor requires a voltage between 3-9V, has a gearbox ratio of 1:48 and a speed of 90RPM at 4.5V. The voltage between positive and...

The DG01D-E is a single hobby motor with a hall speed encoder. This motor requires a voltage between 3-9V, has a gearbox ratio of 1:48 and a speed of 90RPM at 4.5V. The voltage between positive and negative is determined according to the power supply voltage of the single chip microcomputer used, generally 3.3V or 5V is used. The hall sensor can sense the North and South poles of its magnetic plate. When the hall sensor senses the South of the magnetic plate, the hall output will result in a...

This is a breakout board for the L298N full-bridge dual motor driver; which comes in a staggered, Multiwatt package. All pins of the L298N are broken out to a 15-pin 0.1" pitch header. Two mounting...

This is a breakout board for the L298N full-bridge dual motor driver; which comes in a staggered, Multiwatt package. All pins of the L298N are broken out to a 15-pin 0.1" pitch header. Two mounting holes are also provided. Features: Board: 1.6x0.85 inches Documents: Schematic Eagle Files Datasheet (L298N) GitHub (Design Files) ...

This is a 12 VDC brushless fan from Parallax.

This is a 12 VDC brushless fan from Parallax.

2WD miniQ robotic platform is especially designed for students and hobbyists. It's versatile and small, suitable for most indoors applications. It features high quality and powerful metal gear...

2WD miniQ robotic platform is especially designed for students and hobbyists. It's versatile and small, suitable for most indoors applications. It features high quality and powerful metal gear motors which make it a speedy robot. It is ideal for maze competition and educational courses, and is very easy to assemble, check out our assembly video below. Only requires 8 screws to get the job done and you can use our sample codes on our Wiki pages.If you are planning to get started building a...

Robotic arm has been covered a variety of fields, including manufacturing industry, medical treatment, security control and other application. It plays as an assistant, an operator or even a work...

Robotic arm has been covered a variety of fields, including manufacturing industry, medical treatment, security control and other application. It plays as an assistant, an operator or even a work partner, like “Jarvis”!DFLG6DOF is a bionic robotic arm, it consists of six servo motors, corresponding to the arm, elbow, wrist (2 degrees of freedom), five joints and one rotating base in all. Each joint can move in a certain range, and the base can be rotated about 180 degrees. With 24...

The PQ12 series of micro linear actuators are ideal for applications requiring precise positioning and compact size. Weighing in at just 22 grams, the PQ12 is incredibly light as well as compact....

The PQ12 series of micro linear actuators are ideal for applications requiring precise positioning and compact size. Weighing in at just 22 grams, the PQ12 is incredibly light as well as compact. The affordably-priced PQ12 is the most powerful actuator of it's size. This is why it has become a popular choice for OEM manufacturers as well as Arduino and RC hobbyists. Some industries where the PQ12 are in use include: prosthetics, robotics, medical, simulation. The PQ12-R series of linear servos...

These are very handy. They are simple angle brackets with one threaded and unthreaded hole. Use them for connecting PCBs at 90 degree angles, mounting accelerometers, gryros, etc. They can also be...

These are very handy. They are simple angle brackets with one threaded and unthreaded hole. Use them for connecting PCBs at 90 degree angles, mounting accelerometers, gryros, etc. They can also be used on the universal plate set for mounting all sorts of sensors and such. Sold as single units. Documents: Drawing Product Page (612) ...

If you're looking for a sturdy pan-tilt mechanism for most of the cameras that are used with Arduino and Raspberry Pi but don't want the weight of metal, this is the rig for you. The Upgraded Camera...

If you're looking for a sturdy pan-tilt mechanism for most of the cameras that are used with Arduino and Raspberry Pi but don't want the weight of metal, this is the rig for you. The Upgraded Camera Pan Tilt Platform from Arducam takes the basics of a three piece plastic platform connected through two digital servos (included), and adds an I²C controller board for ease of use with your favorite microcontroller or SBC platform. The kit includes all parts and mounting hardware. It does not...

Is your project linked to environmental protection, awareness or study, or to protecting human life? Perhaps you are developing a wildlife tracker, ocean buoy, environmental monitoring system or...

Is your project linked to environmental protection, awareness or study, or to protecting human life? Perhaps you are developing a wildlife tracker, ocean buoy, environmental monitoring system or need to transfer emergency medical information? Do you need to be able to transmit and receive data anywhere? If so, this is the product for you! Our ARGOS Satellite Transceiver Shield allows you to send and receive short bursts of data via the ARGOS satellite network, anywhere on Earth including the...

These basic nylon plastic casters measure 1in. in diameter and offer a simple solution for robotics mobility. These caster balls provide smooth, effortless movement. Note: These are the same casters...

These basic nylon plastic casters measure 1in. in diameter and offer a simple solution for robotics mobility. These caster balls provide smooth, effortless movement. Note: These are the same casters used with the XRP kits Beta & DIY Includes: 2x Nylon Ball Caster Features: Nylon Plastic 1in. Diameter Documents: Drawing ...

These center hole adaptors come in packs of four, are .08” thick, and have an outer diameter .54”. Their ½” diameter lip allows them to fit snuggly into the large holes on Actobotics™ channels that...

These center hole adaptors come in packs of four, are .08” thick, and have an outer diameter .54”. Their ½” diameter lip allows them to fit snuggly into the large holes on Actobotics™ channels that change them from ½” diameter holes to .14” diameter holes perfect for the 6-32 socket head machine screws. Actobotics is a robotics building system based around extruded aluminum channels, gears, precision shafts, and ball bearings. Thanks to the two standardized hole patterns, nearly all Actobotics...

These clamping hubs are a great and cost-effective choice when attaching hub mount gears or wheels to shafts or tubes and can be a better option than set screw hubs if you don't want to risk...

These clamping hubs are a great and cost-effective choice when attaching hub mount gears or wheels to shafts or tubes and can be a better option than set screw hubs if you don't want to risk damaging whatever you need clamped. These clamping hubs have a 5mm bore, four 6-32 tapped holes, one 6-32 machine screw for tightening, and utilizes the 0.77" hub pattern. Actobotics is a robotics building system based around extruded aluminum channels, gears, precision shafts, and ball bearings. Thanks to...

Do you need to be able to sense CO2 concentrations of up to 100%? If so, the STC31 is the sensor for you! The Sensirion STC31 thermal conductivity sensor has two CO2 measurement ranges: 0 to 25...

Do you need to be able to sense CO2 concentrations of up to 100%? If so, the STC31 is the sensor for you! The Sensirion STC31 thermal conductivity sensor has two CO2 measurement ranges: 0 to 25 vol%; and 0 to 100 vol%. The measurement repeatability is 0.2 vol%, with a stability of 0.025 vol% / °C. The measurement accuracy depends on the measurement range: 0.5 vol% + 3% measured value; 1 vol% + 3% measured value. Our breakout includes a separate SHTC3 humidity and temperature sensor; allowing...

These are typical rubber wheels for small robot mobile platforms. The tire is soft black rubber with light tread for added traction in rugged terrain. An axis adapter is needed which bolts to the...

These are typical rubber wheels for small robot mobile platforms. The tire is soft black rubber with light tread for added traction in rugged terrain. An axis adapter is needed which bolts to the back of the hub and mounts to a motor. this adapter(FIT0198) can mount to our Micro DC Geared Motor with Back Shaft(FIT0016). These motors are commonly used in our 4WD and 2WD platforms like Turtle (2WD Arduino Mobile Robot Platform), Pirate (4WD Mobile Platform), Baron(Arduino Mobile Robot Platform...

This is a DFRobot designed silicone wheel comes with high quality ABS material wheel hub and silicone wheel tire. To build your own robot, a proper wheel is always the first thing to look at. A nice...

This is a DFRobot designed silicone wheel comes with high quality ABS material wheel hub and silicone wheel tire. To build your own robot, a proper wheel is always the first thing to look at. A nice looking and soft tire will great make your robot project shine and stunning. This wheel is compatible with our TT Geared DC motors or TT Geared DC Motors with Encoders|Specification|Outside Diameter: 80 mmTire Width: 17 mmShaft hole Size: 5.4 mm in diameter, 3.1 mm thicknessWeight: 40...

Owning a spiderman is a colorful dream in everyone’s childhood. Here is the cute DIY Spider Robot making your dreams come true. With the DIY Spider Robot, you can design and manufacture a...

Owning a spiderman is a colorful dream in everyone’s childhood. Here is the cute DIY Spider Robot making your dreams come true. With the DIY Spider Robot, you can design and manufacture a robotic creature as your wish and under your control!Battery(1.2V) is included. Turn on the switch, you’ll find the little robotic creature is full of energy! The vivid DIY robotic spider with eight multi-jointed legs accurately duplicate the walking movement of real spider.There are two assembly...

This basic DIY Remote Control Robot Kit is designed for you to create a small autonomous or remote controlled robot. Although the kit includes all essential parts to make an autonomous robot, it is...

This basic DIY Remote Control Robot Kit is designed for you to create a small autonomous or remote controlled robot. Although the kit includes all essential parts to make an autonomous robot, it is intended to allow you to add your own electronics in order to satisfy your objectives. |Specification| Platform: Pirate-4WD Mobile Platform 4WD Mobile platform Motors: 3-12V DC peed: 90cm/s Dimensions: 200mm x 170mm x 105mm(7.87"x6.69"x4.13") Microcontroller: Romeo V2(an Arduino Robot Board) DC...

These dolly wheel drive plates provide you with a way to create an easy to assemble, low friction, drive system or motorized dolly platform. The drive B type plates are designed to work with a motor...

These dolly wheel drive plates provide you with a way to create an easy to assemble, low friction, drive system or motorized dolly platform. The drive B type plates are designed to work with a motor and 1” - 2” OD aluminum tubing or PVC pipe from your local hardware store. Each dolly wheel drive plate utilizes the 1.5" hub pattern and are sold in pairs of two. Actobotics is a robotics building system based around extruded aluminum channels, gears, precision shafts, and ball bearings. Thanks to...

These dolly wheel drive plates provide you with a way to create an easy to assemble, low friction, drive system. The idler A type plates are designed to work with 1” - 2” OD aluminum tubing or PVC...

These dolly wheel drive plates provide you with a way to create an easy to assemble, low friction, drive system. The idler A type plates are designed to work with 1” - 2” OD aluminum tubing or PVC pipe from your local hardware store. Each dolly wheel drive plate when fully assembled can hold up to 150lbs, utilizes the 1.5" hub pattern and are sold in pairs of two. Actobotics is a robotics building system based around extruded aluminum channels, gears, precision shafts, and ball bearings....

Parallax ELEV-8 V3 Quadcopter Drone Kit was designed as a durable yet highly functional aerial development platform. A 3lb payload capacity or flights up to 20 minutes on a single battery support a...

Parallax ELEV-8 V3 Quadcopter Drone Kit was designed as a durable yet highly functional aerial development platform. A 3lb payload capacity or flights up to 20 minutes on a single battery support a wide range of experiments and applications. The ELEV-8 V3 has a clean, open plan that requires no soldering for assembly. It is rugged enough to survive most minor crashes. The ELEV-8 v3 was designed in the USA from the ground up to offer the best experience possible for college students, educators,...

The Experiential Robotics Platform (XRP) is a hands-on, comprehensive robotics platform and includes everything needed to build and program a robot to perform beginning through advanced tasks -...

The Experiential Robotics Platform (XRP) is a hands-on, comprehensive robotics platform and includes everything needed to build and program a robot to perform beginning through advanced tasks - building the foundation for innovative thinking, science, engineering, and problem solving. The platform provides: Progression from fundamental robotics to driving, line following, using sensors, using a robotic arm, and culminates in building an autonomous delivery robot Coding environment includes...

The Experiential Robotics Platform (XRP) is a hands-on, comprehensive robotics platform and includes everything needed to build and program a robot to perform beginning through advanced tasks -...

The Experiential Robotics Platform (XRP) is a hands-on, comprehensive robotics platform and includes everything needed to build and program a robot to perform beginning through advanced tasks - building the foundation for innovative thinking, science, engineering, and problem solving. The platform provides: Progression from fundamental robotics to driving, line following, using sensors, using a robotic arm, and culminates in building an autonomous delivery robot Coding environment includes...

DFRobot FireBeetle series are low power consumption microcontrollers designed for Internet of Things (IoT) development. FireBeetle Covers-DC Motor & Stepper Driver is a DC motor & Stepper Motor...

DFRobot FireBeetle series are low power consumption microcontrollers designed for Internet of Things (IoT) development. FireBeetle Covers-DC Motor & Stepper Driver is a DC motor & Stepper Motor driver designed for FireBeetle Microcontrollers. It can control up to four-channels DC motors / two-phase four-wire stepper motors simultaneously.The motor driver cover integrates a STM8 as its coprocessor, controlling the motor speed and direction. It communicates with Microcontroller via IIC port,...

GMR is the abbreviation of General Mobile Robot controller. It's an integrated circuit board specifically designed for home robot platforms, such as HCR (Home Care Robot). In this integrated version...

GMR is the abbreviation of General Mobile Robot controller. It's an integrated circuit board specifically designed for home robot platforms, such as HCR (Home Care Robot). In this integrated version of GMR, you will need three microncontrollers (MCUs): two Arduino Nano / Dream Nano and one Arduino Mega /Arduino Mega ADK, wherein one Nano works as motor control and data acquisition, and the other one as the ultrasonic sensor driver. The Arduino Mega /Mega ADK works as the main controller board...

This is a very handy magnetic mount for survey grade GNSS/GPS antennas. Sturdy, compact, and surprisingly strong, this is a quick way of mounting your antenna to metal roofs, parapets, and other...

This is a very handy magnetic mount for survey grade GNSS/GPS antennas. Sturdy, compact, and surprisingly strong, this is a quick way of mounting your antenna to metal roofs, parapets, and other ferrous materials. The rod is threaded 5/8" 11-TPI (threads per inch) found on high-end surveying antennas and equipment. Additionally, the mount is tall enough to prevent kinking or collision between the TNC connector, cable, and the roof surface. While the magnetic strength is very high, it is not...

Press to release pleasure! Our redesigned digital push buttons come with LED, immersion gold surface, and bright colored hats. A captital D at left corner indicates that it is a digital sensor. An...

Press to release pleasure! Our redesigned digital push buttons come with LED, immersion gold surface, and bright colored hats. A captital D at left corner indicates that it is a digital sensor. An illustration of button painted in the back notifying its function. Pressing it is a real fun, especially with the plastic cap off. The long pressable life also ensures its durability. |Features| Wide voltage range from 3.3V to 5V Standard assembling structure (two 3mm diameter holes with multiple of...

HCR (Home Care Robot) with Omni wheels is a full metal open source mobile robot research platform designed for robotics research and service robot application development.Same as previous...

HCR (Home Care Robot) with Omni wheels is a full metal open source mobile robot research platform designed for robotics research and service robot application development.Same as previous generations, the structure of the HCR is divided into 3 layers, each with slots for installing distance sensors, servos or cameras. There is also plenty of space for other expansions modules. More than that, equipped with 3 high torque Omni wheels with encoders, it is capable of all-direction pinpoint...

The HCR Mobile Robot Kit is a two wheel drive mobile robot platform with three levels (if you want, you can use only the parts you need, or make a two level robot). The kit contains two motors, two...

The HCR Mobile Robot Kit is a two wheel drive mobile robot platform with three levels (if you want, you can use only the parts you need, or make a two level robot). The kit contains two motors, two wheels, an omni-directional wheel, and hardware accessories such as metal plates. Its support structure includes servos and sensors, with special interfaces for a mini - ITX motherboard.As the second generation of DFRobot's HCR (Home Care Robot) platform, we have equipped it with new motors and...

The HCR Mobile Robot Kit is a two wheel drive mobile robot platform with three levels (if you want, you can use only the parts you need, or make a two level robot). The mobile robot kit contains two...

The HCR Mobile Robot Kit is a two wheel drive mobile robot platform with three levels (if you want, you can use only the parts you need, or make a two level robot). The mobile robot kit contains two motors, two wheels, an omni-directional wheel, and hardware accessories such as metal plates. Its support structure includes servos and sensors, with special interfaces for a mini - ITX motherboard.As the second generation of DFRobot's HCR (Home Care Robot) platform, we have equipped it with new...

These aluminum hex standoffs are 2.375in. (60.33mm) long and tapped for a 4-40 screw. These are great for mounting your board in an enclosure, or just getting it up off the table. Sold individually....

These aluminum hex standoffs are 2.375in. (60.33mm) long and tapped for a 4-40 screw. These are great for mounting your board in an enclosure, or just getting it up off the table. Sold individually. Features: Screw, Thread Size: #4-40 Diameter - Outside: 0.250" (6.35mm) 1/4" Hex Between Board Height: 2.375" (60.33mm) 2 3/8" Length - Overall: 2.375" (60.33mm) 2 3/8"

This is a hobby gearmotor from DAGU. These gearmotors are the same ones recommended for use in the Shadow Chassis and offer a cheap and easy-to-use setup to get your wheels turning. Each Hobby...

This is a hobby gearmotor from DAGU. These gearmotors are the same ones recommended for use in the Shadow Chassis and offer a cheap and easy-to-use setup to get your wheels turning. Each Hobby Gearmotor also possess a 9mm long output on a straight axis. These gearmotors require a voltage of 4.5V with a no load current of 190mA while possessing a gearbox ratio of 48:1 and a wheel speed of 140 RPM unloaded. Features: Suggested Voltage: 4.5VDC No Load Speed: 140RPM No Load Current: 190mA Max....

The JetBot Chassis Kit V2 is the official chassis used on the SparkFun JetBot AI Kit but can be used for many different robotics platforms. The chassis plates are made from 3.5mm thick ABS plastic...

The JetBot Chassis Kit V2 is the official chassis used on the SparkFun JetBot AI Kit but can be used for many different robotics platforms. The chassis plates are made from 3.5mm thick ABS plastic milled with plenty of mounting points for sensors, servos, controllers, power and more. Assembly is simple; with just a few included screws needed for construction, you will have a reliable 2WD robotics chassis. A great economical option for desktop robots. The JetBot chassis kit comes with two...

The Kitronik :MOVE mini MK 2 buggy kit for the BBC micro:bit is the latest version of the ever popular :MOVE mini that provides a fun introduction to robotics. The :MOVE mini is a 2 wheeled robot...

The Kitronik :MOVE mini MK 2 buggy kit for the BBC micro:bit is the latest version of the ever popular :MOVE mini that provides a fun introduction to robotics. The :MOVE mini is a 2 wheeled robot that is suitable for autonomous operation, remote control projects via a Bluetooth application or being controlled using a second BBC microbit as a controller via the microbits radio functionality. The MK2 features a brand new set of Kitronik injection moulded wheels with 0-ring rubber tires. The...

The Kitronik Autonomous Robotics Platform for Raspberry Pi Pico is a fun and hands-on introduction to buggy robotics. The easy to follow booklet provided with the kit guides you through all of the...

The Kitronik Autonomous Robotics Platform for Raspberry Pi Pico is a fun and hands-on introduction to buggy robotics. The easy to follow booklet provided with the kit guides you through all of the steps required for you to take control of your robot. The Robotics Platform has been designed to grow with you and provided additional servo and ultrasonic sensor connectors for more advanced projects. This buggy requires a Raspberry Pi Pico with pin headers attached. The kit is supplied with the...

This board allows the Raspberry Pi Pico (connected via pin header) to drive two motors simultaneously with full forward, reverse & stop control, making it ideal for Pico controlled buggy projects....

This board allows the Raspberry Pi Pico (connected via pin header) to drive two motors simultaneously with full forward, reverse & stop control, making it ideal for Pico controlled buggy projects. Alternatively, the board can be used to power a stepper motor. The board features the DRV8833 motor driver IC, which has built-in short circuit, over current and thermal protection. The board has four external connections to GPIO pins and a 3V and GND supply from the Pico. This allows for additional...

The compact Simply Servo board for Raspberry Pi Pico allows for up to 8 servos to be controlled simultaneously, making it ideal for advanced robotics projects with the RiPi Pico. The board should be...

The compact Simply Servo board for Raspberry Pi Pico allows for up to 8 servos to be controlled simultaneously, making it ideal for advanced robotics projects with the RiPi Pico. The board should be used with a Pico that has soldered pin headers, the Pico can then slot straight into the board. A Pico with pin headers already attached can be obtained separately here. The board features standard 3-pin servo connectors which allow for servos to be plugged straight in without the need for adaptors...

This hardware kit consists of 4 each of M2 style nylon hex nuts and screws. It is designed for use with the Leopard Imaging Camera, but can be used for other mountings as well. This hardware set is...

This hardware kit consists of 4 each of M2 style nylon hex nuts and screws. It is designed for use with the Leopard Imaging Camera, but can be used for other mountings as well. This hardware set is identical to what is included in our JetBot kit options. Includes: 4x - M2 Nylon Hex Nut 4x - M2 Nylon Screw - slotted drive, 6mm ...

How can your robot rule the world with an iron fist if it doesn't have a hand? This LG-NS robot gripper makes a great addition to a small arm or mobile base. The gripper features injection molded...

How can your robot rule the world with an iron fist if it doesn't have a hand? This LG-NS robot gripper makes a great addition to a small arm or mobile base. The gripper features injection molded components and can use two standard hobby servos (not included) for open and close and wrist rotate. The clamp open to 1.3" and the wrist rotates approximately 180 degrees. It needs only a screw driver for assembly. Notice Compatible servo: Hitec 422 servos |Specification| Max clamp width: 1.3" Size:...

Do you have some liquids that you need to move? This fluid pump will move 500 gallons per hour! The SEAFLO mini water pump has a heavy duty 12V, 1.5Amp motor and a tough thermoplastic body. This...

Do you have some liquids that you need to move? This fluid pump will move 500 gallons per hour! The SEAFLO mini water pump has a heavy duty 12V, 1.5Amp motor and a tough thermoplastic body. This bilge pumps offer water evacuation activated by a panel or float switch. It includes anti-airlock protection and exclusive moisture tight seals, marine grade blocked wiring. It's totally submersible and water-cooled (but it won't burn out if run dry). Use this pump to make a fountain or waterfall, even...

This is an M3 hex nut. For use with M3 screws.

This is an M3 hex nut. For use with M3 screws.

The Magnetic Imaging Tile uses an array of 64 hall effect sensors to convert magnetic fields to the visual spectrum. That's right! You can now see magnetic fields in real time! As is to be expected,...

The Magnetic Imaging Tile uses an array of 64 hall effect sensors to convert magnetic fields to the visual spectrum. That's right! You can now see magnetic fields in real time! As is to be expected, there are caveats: the magnetic sensors used on the tile are some of the most sensitive on the market but you need to be within 1 to 2 centimeters of the tile to get a good image. The Magnetic Imaging Tile uses the following components: Magnetic Sensor (64 pixels): DRV5053VA -90mV/mT...

The Mates Stand offers a simple connection for a MatesBUS compatible device, such as the TIMI-96. It eases development by propping the MatesBus compatible device up on an angle (35 degrees off...

The Mates Stand offers a simple connection for a MatesBUS compatible device, such as the TIMI-96. It eases development by propping the MatesBus compatible device up on an angle (35 degrees off vertical), aiding development when standing on a desk or bench. The Mates Stand breaks out the ten signals found on the MatesBUS interface into two separate 5-pin headers, one out of each side of the stand itself, allowing easy connections to the Mates Programmer. The headers are also easy to attach...

This gearmotor consists of a low-power, 12 V brushed DC motor combined with a 9.68:1 metal spur gearbox, and it has an integrated 48 CPR quadrature encoder on the motor shaft, which provides 464.64...

This gearmotor consists of a low-power, 12 V brushed DC motor combined with a 9.68:1 metal spur gearbox, and it has an integrated 48 CPR quadrature encoder on the motor shaft, which provides 464.64 counts per revolution of the gearbox’s output shaft. The gearmotor is cylindrical, with a diameter just under 25 mm, and the D-shaped output shaft is 4 mm in diameter and extends 12.5 mm from the face plate of the gearbox. A two-channel Hall effect encoder is used to sense the rotation of a magnetic...

These micro gearmotors are incredibly tough and feature full metal gears. They have a gear ratio of 150:1 and operate up to 12 volts and have a stall torque of 45 oz-in. and a max speed of 175 RPM....

These micro gearmotors are incredibly tough and feature full metal gears. They have a gear ratio of 150:1 and operate up to 12 volts and have a stall torque of 45 oz-in. and a max speed of 175 RPM. Each micro gearmotor sports a 3mm D-shaft. Note: The micro gearmotor enclosures are sold separately, you can find them here. Features: Voltage: 6 - 12 Volts Gear Ratio: 150:1 Stall Torque: 17/45 oz-in. (6/12V) Speed: 90/175 RPM (6/12V) No Load Current: 40/70 mA (6/12V) Stall Current: 360/1600 mA...

These micro gearmotors are incredibly tough and feature full metal gears. They have a gear ratio of 50:1 and operate up to 12 volts and have a stall torque of 20 oz-in. and a max speed of 460 RPM....

These micro gearmotors are incredibly tough and feature full metal gears. They have a gear ratio of 50:1 and operate up to 12 volts and have a stall torque of 20 oz-in. and a max speed of 460 RPM. Each micro gearmotor sports a 3mm D-shaft. Note: The micro gearmotor enclosures are sold separately, you can find them here. Features: Voltage: 6 - 12 Volts Gear Ratio: 50:1 Stall Torque: 7/20 oz-in. (6/12V) Speed: 240/460 RPM (6/12V) No Load Current: 40/100 mA (6/12V) Stall Current: 360/1600 mA...

These micro gearmotors are incredibly tough and feature full metal gears. They have a gear ratio of 298:1 and operate up to 12 volts and have a stall torque of 70 oz-in. and a max speed of 90 RPM....

These micro gearmotors are incredibly tough and feature full metal gears. They have a gear ratio of 298:1 and operate up to 12 volts and have a stall torque of 70 oz-in. and a max speed of 90 RPM. Each micro gearmotor sports a 3mm D-shaft. Note: The micro gearmotor enclosures are sold separately, you can find them here. Features: Voltage: 6 - 12 Volts Gear Ratio: 298:1 Stall Torque: 40/70 oz-in. (6/12V) Speed: 45/90 RPM (6/12V) No Load Current: 30/70 mA (6/12V) Stall Current: 360/1600 mA...

These enclosures allow you to mount your micro gearmotor to other Actobotics products easily. Once your gearmotor is inserted, you can take advantage of the 0.77” hole pattern. These enclosures have...

These enclosures allow you to mount your micro gearmotor to other Actobotics products easily. Once your gearmotor is inserted, you can take advantage of the 0.77” hole pattern. These enclosures have a length of 1.14”, a width of 1”, and a thickness of 0.50”. Actobotics is a robotics building system based around extruded aluminum channels, gears, precision shafts, and ball bearings. Thanks to the two standardized hole patterns, nearly all Actobotics components can be intuitively connected...

This custom-designed rubber wheel has a rubber tire with a diameter of 1.69" (43 mm). It is designed to fit the output shafts on our mini metal gear motors as well as the Solarbotics metal gear...

This custom-designed rubber wheel has a rubber tire with a diameter of 1.69" (43 mm). It is designed to fit the output shafts on our mini metal gear motors as well as the Solarbotics metal gear motors. Teeth on the hub optionally allow a reflectance sensor to be used for encoder feedback.Gear motors should be mounted onto the side of the hub with the protruding teeth. The output shaft will slide into the socket easily at first but will achieve a snug fit when pressed through to the other edge...

Description: These are standard nuts with 2-56 thread. For use with 2-56 machine screws and five button pad set listed below. Sold in single units.

Description: These are standard nuts with 2-56 thread. For use with 2-56 machine screws and five button pad set listed below. Sold in single units.

Give your robot some traction with this 2-pack of rubber O-rings. Measuring 55mm outer diameter, 45mm inner diameter, and 5mm wire diameter, they provide a reliable and versatile solution for a...

Give your robot some traction with this 2-pack of rubber O-rings. Measuring 55mm outer diameter, 45mm inner diameter, and 5mm wire diameter, they provide a reliable and versatile solution for a two-wheel robotics platform. Note: These are the same o-rings used with the XRP kits Beta & DIY Includes: 2x Rubber O-Ring Features: Outer Diameter: 55mm Inner Diameter: 45mm Wire Diameter: 5mm Documents: Drawing ...

This pan/tilt bracket consists of two brackets and all the hardware you need to attach them to make a pan/tilt mechanism using two servo motors. We recommend our small servo motors listed below....

This pan/tilt bracket consists of two brackets and all the hardware you need to attach them to make a pan/tilt mechanism using two servo motors. We recommend our small servo motors listed below. Note: Servos are not included. The sub-micro servo size works for these mounts. Documents: Dimensional Drawing Assembly Guide Face Tracking Tutorial Videos ...

The Pixhawk® 6C is the latest update to the successful family of Pixhawk® flight controllers, based on the Pixhawk® FMUv6C Open Standard and Connector Standard. It comes with PX4 Autopilot®...

The Pixhawk® 6C is the latest update to the successful family of Pixhawk® flight controllers, based on the Pixhawk® FMUv6C Open Standard and Connector Standard. It comes with PX4 Autopilot® pre-installed. Inside the Pixhawk® 6C, you can find an STMicroelectronics® based STM32H743, paired with sensor technology from Bosch® & InvenSense®, giving you flexibility and reliability for controlling any autonomous vehicle, suitable for both academic and commercial applications. The Pixhawk® 6C's H7...

The Pixhawk® 6C with M8N GPS is the latest update to the successful family of Pixhawk® flight controllers, based on the Pixhawk® FMUv6C Open Standard and Connector Standard. It comes with PX4...

The Pixhawk® 6C with M8N GPS is the latest update to the successful family of Pixhawk® flight controllers, based on the Pixhawk® FMUv6C Open Standard and Connector Standard. It comes with PX4 Autopilot® pre-installed. Inside the Pixhawk® 6C, you can find an STMicroelectronics® based STM32H743, paired with sensor technology from Bosch® & InvenSense®, giving you flexibility and reliability for controlling any autonomous vehicle, suitable for both academic and commercial applications. The...

The Pixhawk® 6C is the latest update to the successful family of Pixhawk® flight controllers, based on the Pixhawk® FMUv6C Open Standard and Connector Standard. It comes with PX4 Autopilot®...

The Pixhawk® 6C is the latest update to the successful family of Pixhawk® flight controllers, based on the Pixhawk® FMUv6C Open Standard and Connector Standard. It comes with PX4 Autopilot® pre-installed. Inside the Pixhawk® 6C, you can find an STMicroelectronics® based STM32H743, paired with sensor technology from Bosch® & InvenSense®, giving you flexibility and reliability for controlling any autonomous vehicle, suitable for both academic and commercial applications. The Pixhawk® 6C's H7...

The Pixhawk® 6C with M8N GPS is the latest update to the successful family of Pixhawk® flight controllers, based on the Pixhawk® FMUv6C Open Standard and Connector Standard. It comes with PX4...

The Pixhawk® 6C with M8N GPS is the latest update to the successful family of Pixhawk® flight controllers, based on the Pixhawk® FMUv6C Open Standard and Connector Standard. It comes with PX4 Autopilot® pre-installed. Inside the Pixhawk® 6C, you can find an STMicroelectronics® based STM32H743, paired with sensor technology from Bosch® & InvenSense®, giving you flexibility and reliability for controlling any autonomous vehicle, suitable for both academic and commercial applications. The...

This is a simple ~140RPM (no load), DC planetary gearmotor. This motor is great for various applications such as robotics, electric locks, household automation, and small actuators. The supply...

This is a simple ~140RPM (no load), DC planetary gearmotor. This motor is great for various applications such as robotics, electric locks, household automation, and small actuators. The supply voltage range is 6VDC - 24VDC with the polarity marker at the base of the motor. The planetary gear box, mounted on top of the motor housing, gives this motor a relatively large stall torque for its size. The overall body of the motor is made of metal, with the exception of the set of planet gears on the...

Qwiic Boost increases the Qwiic bus from 3.3V to 5V while still providing the target device with 3.3V I2C signals. This is a handy board for connecting technologies that still require 5V for running...

Qwiic Boost increases the Qwiic bus from 3.3V to 5V while still providing the target device with 3.3V I2C signals. This is a handy board for connecting technologies that still require 5V for running higher voltage mechanisms (like a DC fan) but have an internal processor running at 3.3V. We've seen this a lot with air quality sensors that use a fan to push air into a test chamber. The 5V boost circuit is rated up to 100mA with 90% efficiency. For applications where the 5V device needs 5V I2C...

With a clear view of the sky, the Qwiic Iridium 9603 allows you to send and receive short messages. It works anywhere in the world, far beyond the reach of WiFi and GSM networks. Maybe you want to...

With a clear view of the sky, the Qwiic Iridium 9603 allows you to send and receive short messages. It works anywhere in the world, far beyond the reach of WiFi and GSM networks. Maybe you want to transmit weather information from a weather station on top of a mountain? Or use it to send data from a travelling balloon sat? Perhaps you need to communicate in an emergency, when other networks might not be available? At the heart of our product is an Iridium 9603 modem. The Qwiic module hosts the...

The RC Air Mouse and Keyboard uses the latest 2.4GHz wireless technology with a sampling frequency up to 120Hz. Use it like a Wii remote to control your mouse cursor on the screen. Operation is...

The RC Air Mouse and Keyboard uses the latest 2.4GHz wireless technology with a sampling frequency up to 120Hz. Use it like a Wii remote to control your mouse cursor on the screen. Operation is flexible and smooth and does no connection is lost during rapid movement.The RC Air Mouse and Keyboard can be used for a wide range of devices and drivers install automatically when you plug it in. With a wide transmission range of up to 30m, you can use this remote control your computer in style. Sit...

This is a 2 DOF robot gripper that can be installed with 2 servos so as to control gripper opening and closing with one servo, and steering gear motion control (or rotation) with the other...

This is a 2 DOF robot gripper that can be installed with 2 servos so as to control gripper opening and closing with one servo, and steering gear motion control (or rotation) with the other servo.Velocity range is 0 to 54 mm (0 to 2.13"). Total weight about 45 g. The servo slot fit most servos such as Hitec 422,475, DSS-P05 Standard Servo, DF Metal Geared 15Kg Standard Servo. |Specification| Clamp range:0-54mm (0-2.13") Size:105x100x30mm (4.13x3.94x1.18")|ShippingList| Robot Gripper-Extra Width...

Does your robot crush objects with its hulkishly strong grip? Give your robotic hand or claw a better sense of touch with the Robotic Finger Sensor. This new version adds pressure sensing so now you...

Does your robot crush objects with its hulkishly strong grip? Give your robotic hand or claw a better sense of touch with the Robotic Finger Sensor. This new version adds pressure sensing so now you can know how hard you're gripping! The Robotic Finger Sensor (RFS) uses a unique combination of infrared distance sensing, pressure sensing, optical encapsulant, and data filtering to detect extremely light touches. Additionally, the silicon covering is squishy, giving the sensor increased grip...