DFRobot

This is an arduino basic kit for building an omni-directional robot or an obstacle avoidance control system. It includes a DFRduino mega 2560 controller, a mega IO expansion shield, four infrared...

This is an arduino basic kit for building an omni-directional robot or an obstacle avoidance control system. It includes a DFRduino mega 2560 controller, a mega IO expansion shield, four infrared distance sensors, and two motor drivers.|Specification| DFRduino Mega 2560 Microcontroller: ATmega2560 Operating Voltage: 5V Input Voltage (recommended): 7-12V Distance measuring range: 10 cm to 80 cm (4" to 32")in 4 Direction Drive Type: Dual high-power H-bridge driver Drive part of the operating...

Geared DC Motor and Housing Simple, cheap DC geared motor for those applications when steppers or servos are over kill or too costly. We love cheap DC motors and use them by the dozen so we thought...

Geared DC Motor and Housing Simple, cheap DC geared motor for those applications when steppers or servos are over kill or too costly. We love cheap DC motors and use them by the dozen so we thought it was about time we offered them to you. These are easy to run with an H-Bridge and integrate into your projects at a very cost effective price point. We hope you enjoy. Note: They come as a pair. 2x DC motors and 2x gearboxes. Suggested Voltage: 3V DC        ...

This is a very popular LCD Keypad shield for Arduino and other variants. It includes a 2x16 LCD display and 6 momentary push buttons. Pins 4, 5, 6, 7, 8, 9 and 10 are used to interface with the LCD....

This is a very popular LCD Keypad shield for Arduino and other variants. It includes a 2x16 LCD display and 6 momentary push buttons. Pins 4, 5, 6, 7, 8, 9 and 10 are used to interface with the LCD. Just one Analog Pin 0 is used to read the five pushbuttons. The LCD shield supports contrast adjustment and back-lit on/off functions. It also exposes five analog pins with DFRobot color code for easy analog sensor plugging and display. The on board LED indicates power on.This lcd arduino shield...

The Arduino XBee shield is designed to meet wireless sensor networks such as wifi, bluetooth 2.0/4.0 and zigbee. The module is easy to use, low power consumption, and the provision of critical data...

The Arduino XBee shield is designed to meet wireless sensor networks such as wifi, bluetooth 2.0/4.0 and zigbee. The module is easy to use, low power consumption, and the provision of critical data between devices reliable transmission. This xbee shield for arduino can be directly stack on top of Arduino Uno / Leonardo and Mega. It provides a 5-3.3V voltage converter to allow 3.3V communication modules to interface Arduino 5V system. The compatibility of this arduino xbee shield is now...

The DFRobot Relay Module is a standard relay used with a controller board to interface external electrical circuits or modules. Some of the most common applications with Arduino are: Home lighting,...

The DFRobot Relay Module is a standard relay used with a controller board to interface external electrical circuits or modules. Some of the most common applications with Arduino are: Home lighting, electrical appliances of high power and other equipments. The modular design makes it easy to integrate with a controller board. The Relay integrates a status LED, in order to acknowledge visually it's status ON or OFF. It can be controlled through the digital IO port, with a simple HIGH or LOW on...

This is DFRobot's basic sensor set for arduino. Set includes light sensor, touch sensor, temperature sensor, magnetic sensor, vibration sensor, tilt sensor, big button, LED lighting module and...

This is DFRobot's basic sensor set for arduino. Set includes light sensor, touch sensor, temperature sensor, magnetic sensor, vibration sensor, tilt sensor, big button, LED lighting module and Grayscale sensor.To connect these sensors to Arduino, we suggest to use our IO expansion shield V7.1 which has color coded pins that provides a much easier way to link sensors to microcontroller. |Specification| Analog Ambient light sensor (DFR0026) Digital Capacitive touch sensor (DFR0030) LM35...

This is an Arduino Temperature Sensor based on LM35 temperature chip. A Temperature Sensor can be used to detect ambient air temperature.The LM35 chip is produced by National Semiconductor...

This is an Arduino Temperature Sensor based on LM35 temperature chip. A Temperature Sensor can be used to detect ambient air temperature.The LM35 chip is produced by National Semiconductor Corporation and offers a functional range between 0 degree Celsius to 100 degree Celsius with a sensitivity of 10mV per degree Celsius. The output voltage is proportional to the temperature.It is commonly used as a temperature measurement sensors. It includes thermocouples, platinum resistance, thermal...

While there are many types of temperature sensors available in the market, the DS18B20 arduino Temperature Sensor form DALLAS is the best choice in applications which require high accuracy and high...

While there are many types of temperature sensors available in the market, the DS18B20 arduino Temperature Sensor form DALLAS is the best choice in applications which require high accuracy and high reliability. Its ultra-small size, low hardware overhead, strong anti-interference capability and high accuracy, together with other additional features makes DS18B20 even more popular among users. For electronic enthusiasts and hobbyists, the DS18B20 is a good start for learning and developing...

What's the simplest way to check vibration with Arduino? Use a vibration sensor from DFRobot. You can directly plug it on our IO Expesion Shield V7. Just vibrate this sensor, Arduino can receive a...

What's the simplest way to check vibration with Arduino? Use a vibration sensor from DFRobot. You can directly plug it on our IO Expesion Shield V7. Just vibrate this sensor, Arduino can receive a digital signal. It's easy to acount and program in Arduino. Despite it's simple, you can make full use of it with creative thinking, like step counting, Crash warning light and so on. Inprovement Wide voltage range from 3.3V to 5V Standard assembling structure (Times-of-5mm Center distance between...

This is an arduino tilt sensor. It is used to detect orientation. Inside the sensor, there is a ball that make contact with the pins when the case is upright. Tilt the sensor over and the balls...

This is an arduino tilt sensor. It is used to detect orientation. Inside the sensor, there is a ball that make contact with the pins when the case is upright. Tilt the sensor over and the balls don’t touch, thus not making a connection.Here is the principle of tilt sensor to illustrate how it works: Simple plug to our Arduino IO Sensor Expansion Shield, you can make amazing interactive projects. As this sensor is now woking under 3.3V, it is now able to be compatible with Raspberry Pi....

what's the best way to detect the magnet? Use anther magnet. But it's not sensitive enough. You have to feel it by youself.Right. This magnetic sensor knows whether there is a magnetic object nearby...

what's the best way to detect the magnet? Use anther magnet. But it's not sensitive enough. You have to feel it by youself.Right. This magnetic sensor knows whether there is a magnetic object nearby or not. And it correctly tells you through ditigal output.See below picture for a quick demo! |Features| Wide voltage range from 3.3V to 5V Standard assembling structure (Times-of-5mm Center distance between two 3mm mounting holes) Easily recognitive interfaces of sensors ("A" for analog and "D"...

This is a new Arduino compatible Analog Sound Sensor. Sound Sensor is typically used in detecting the loudness in ambient, the Arduino can collect its output signal and actuate accordingly. You may...

This is a new Arduino compatible Analog Sound Sensor. Sound Sensor is typically used in detecting the loudness in ambient, the Arduino can collect its output signal and actuate accordingly. You may use it to make some funny interactive works such as a "clap and buzz" to find your lost keys or remote control if you add a buzzer. This sensor works best with our Audio analyzer module. As one of our new version of breakout boards, we have improved the analog sound sensor in below: Wide voltage...

Analog Gas Sensor Introduction The gas sensor detects smoke, methane, carbon dioxide and other gases. It is able to give alarms when the smoke/gas leaks.  You can adjust the sensitivity with...

Analog Gas Sensor Introduction The gas sensor detects smoke, methane, carbon dioxide and other gases. It is able to give alarms when the smoke/gas leaks.  You can adjust the sensitivity with the potentiometer. Specification Type: Analog Detector: QM-NG1 Power supply needs: 5V Current: 100mA Pin Definition:  1-Output  2-GND  3-PWR  Document Datasheet Manual Shipping List Sensor (1 unit) Analog Sensor Cable (1 unit) (SKU:FIT0031) ...

The upgraded DFRobot Xbee USB adapter is designed for the XBee module configuration parameters to facilitate using or to work as a FTDI writer. The new version of Xbee USB adapter is also welded...

The upgraded DFRobot Xbee USB adapter is designed for the XBee module configuration parameters to facilitate using or to work as a FTDI writer. The new version of Xbee USB adapter is also welded with the female pin for FTDI so that users can directly use the adapter as a FTDI program writer, such as Arduino FIO/pro/mini?lilypad Arduino and so on. It's a must-have for interactive electronic installations and projects.The adapter allows the PC to configure XBee / Bluetooth module and the...

The Analog Voltage Divider V2 can detect the supply voltage from 0.0245V to 25V. This module is based on resistor divider principle. The voltage detection module allows the input voltage to reduce 5...

The Analog Voltage Divider V2 can detect the supply voltage from 0.0245V to 25V. This module is based on resistor divider principle. The voltage detection module allows the input voltage to reduce 5 times. As the Arduino analog input voltage is normally maximum 5V, the input voltage of analog voltage detection module can not exceed 5Vx5 which is 25V.Notice: The new version of analog sensor port pin mapping has been changed as the following two features. Inprovement List Wide voltage range from...

The DFRobot Vibration Sensor buffers a piezoelectric transducer that responds to strain changes by generating a measurable output voltage change which is propotional with the strength of...

The DFRobot Vibration Sensor buffers a piezoelectric transducer that responds to strain changes by generating a measurable output voltage change which is propotional with the strength of vibration.So you can know the extent of vibration. Different from digital vibration sensor that only accounts times, this analog one can tell extent of vabiration.|Specification| Supply Voltage: 3.3V to 5V Interface: Analog Size:22x30mm (0.87x1.2'') |Documents| Wiki Analog Piezo Disk Vibration Sensor...

The WiiChuck Adapter is a small PCB that is designed to be inserted into the connector of a Nintendo Wii Nunchuck to provide access to all 4 wires of the remote. The power, ground and two-wire...

The WiiChuck Adapter is a small PCB that is designed to be inserted into the connector of a Nintendo Wii Nunchuck to provide access to all 4 wires of the remote. The power, ground and two-wire interface of the Nunchuck are all broken out to a 4-pin 0.1" pitch header. Compared with standard WiiChuck, the DFRobot WiiChuck has extra 4 pins which allow you connect it to two devices. The Wii Nunchuck is loaded with features -- a 2-axis joystick, two buttons and a 3 axis ?2g accelerometer -- and any...

This is a basic breakout board for the FTDI FT232RL USB to serial IC. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 3.3V Arduino boards. It can also be...

This is a basic breakout board for the FTDI FT232RL USB to serial IC. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 3.3V Arduino boards. It can also be used for general serial applications. The major difference with this board is that it brings out the DTR pin as opposed to the RTS pin of the FTDI cable. The DTR pin allows an Arduino target to auto-reset when a new Sketch is downloaded. This is a really nice feature to have and allows a sketch to be...

DHT11 Temperature and Humidity Sensor This DHT11 Temperature and Humidity Sensor features a calibrated digital signal output with the temperature and humidity sensor complex. Its technology ensures...

DHT11 Temperature and Humidity Sensor This DHT11 Temperature and Humidity Sensor features a calibrated digital signal output with the temperature and humidity sensor complex. Its technology ensures the high reliability and excellent long-term stability. A high-performance 8-bit microcontroller is connected. This sensor includes a resistive element and a sense of wet NTC temperature measuring devices. It has excellent quality, fast response, anti-interference ability and high cost performance...

Triple Axis Accelerometer MMA7260 The MMA7260Q is a very nice sensor with easy analog interface. The MMA7260QT is a 3.3V part and outputs an analog voltage for each of the three outputs. This...

Triple Axis Accelerometer MMA7260 The MMA7260Q is a very nice sensor with easy analog interface. The MMA7260QT is a 3.3V part and outputs an analog voltage for each of the three outputs. This voltage is in ratio to the measured acceleration and to the supply voltage (ratiometric). It has selectable sensitivity by dip switch.  You will need some extra hardware to convert this analog signal to a usable digital one.  The Arduino is really good option for it.  This break...

This DFRobot SD card shield is a Break out board for standard SD card. It allows you to add mass storage and data logging to your project. |Specification| Break out board for standard SD card and...

This DFRobot SD card shield is a Break out board for standard SD card. It allows you to add mass storage and data logging to your project. |Specification| Break out board for standard SD card and Micro SD (TF) card Contains a switch to select the flash card slot Sits directly on a Arduino Also be used with other microcontrollers|Documents| Wiki Doc Arduino Library|ShippingList| SD Module x1 ...

This Arduino flame sensor can be used to detect fire or other wavelength at 760 nm ~ 1100 nm light. In the fire-fighting robot game, the flame plays an important role in the probe, which can be used...

This Arduino flame sensor can be used to detect fire or other wavelength at 760 nm ~ 1100 nm light. In the fire-fighting robot game, the flame plays an important role in the probe, which can be used as the robot's eyes to find fire source or football. It can make use of fire-fighting robots, soccer robots. The Flame sensor has probe angle of 60 degrees, two M3 mounting holes is provided to install on various platforms. This arduino flame sensor's operating temperature is -25 degrees Celsius to...

IO Expansion Shield For Arduino(V5) This IO expansion board is evolving, this latest V5 IO expansion shield is now supporting Xbee. It combines the popular Xbee shield with I...

IO Expansion Shield For Arduino(V5) This IO expansion board is evolving, this latest V5 IO expansion shield is now supporting Xbee. It combines the popular Xbee shield with IO expansion shield(V4). It even supports SD card which provides the ultimate functional expansion for Arduino so far.   Specification Support RS485 Support Xbee (Xbee pro) Support Bluetooth Support APC220 Support SD card read/write Check out the DFRobot Sensors that work with this...

This LCD module uses a 128x64 liquid crystal display that support Chinese character, English characters and even graphics. It is suitable for interactive work with Arduino.It features a backlit...

This LCD module uses a 128x64 liquid crystal display that support Chinese character, English characters and even graphics. It is suitable for interactive work with Arduino.It features a backlit control, pallerlel or serial control, contrast adjust. It can be connect to our interface shield for arduino via IDC6 socket and Cable for Shiftout.The LCD is shipped in Pallelel mode in default. The R9 is used to set the interface mode. To switch to SPI mode, the R9 resistor need to be moved to...

Graphic LCD4884 Shield For Arduino Introduction This LCD4884 Shield provides 48x48 display. If your project need more information to display, this LCD shield can apparently meet your needs. It is...

Graphic LCD4884 Shield For Arduino Introduction This LCD4884 Shield provides 48x48 display. If your project need more information to display, this LCD shield can apparently meet your needs. It is able to display English, Chines, even images. It also integrates a 5 DOF joystick.  The shield has 6 Digital IO and 5 Analog IO.  Note:The Arduino in the image is NOT included. Specification Power Supply: 5V SPI Interface (using Arduino Digital Pin 2,3,4,5,6) One Reset button One 5 degree...

An infrared transmitter is simply a Light Emitting Diode which generates IR light (invisible IR light)--light with a wavelength of between 1 mm and 750 nanometers, and some associated circuitry. In...

An infrared transmitter is simply a Light Emitting Diode which generates IR light (invisible IR light)--light with a wavelength of between 1 mm and 750 nanometers, and some associated circuitry. In an infrared remote control, for example, pushing a button sends an electric signal to the LED, which converts the signal into a beam of infrared light. The receiving device detects the light with a photo diode and converts it to an electrical signal which, via an integrated circuit, controls its...

This IR kit provides a remote control capability to your project. |Documents| Wiki Arduino Library (Compatible with Leonardo)|ShippingList| IR Remote Controller (With battery CR2025 inside) x1 IR...

This IR kit provides a remote control capability to your project. |Documents| Wiki Arduino Library (Compatible with Leonardo)|ShippingList| IR Remote Controller (With battery CR2025 inside) x1 IR Receiver Module x1 (SKU: DFR0094) Digital Cable x1|Projects|Project 1. Summer inspiration-DIY automatic curtain liftList of hardware: 1. Romeo-All in one Controller(DFR0004) 2. IR Kit(DFR0107) 3. Adjustable Infrared Sensor Switch (SEN0019) 4. DC motor (12V- FIT0493, FIT0277)5. 12V power adapter6....

Introduction This is DFRduino UNO (SMD version).  It is a totally Arduino UNO compatible clone - just at a reduced price. The Arduino UNO is a microcontroller board based on the ATmega328...

Introduction This is DFRduino UNO (SMD version).  It is a totally Arduino UNO compatible clone - just at a reduced price. The Arduino UNO is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a...

Now, it is time to add a more fancy interactive way to your project. This DFRobot touch kit comes with three types touch sensors. An ipod styple wheel touch, a keypad touch which supports backlit...

Now, it is time to add a more fancy interactive way to your project. This DFRobot touch kit comes with three types touch sensors. An ipod styple wheel touch, a keypad touch which supports backlit and a grid touch pad which can recoginze something unique. This kit utilizes the not very "latest" capactive touch technology which make the sensing very sensitive. The kit is designed to be compatible with Arduino. Get Started with Capacitive Touch Kit Tutorial|Specification| Operation Voltage:5V...

Combines the power of screw shield and prototyping shield. This Proto Screw shield offers a better way to do prototyping. The Screw terminal can be screwed directly to the terminal on the thread and...

Combines the power of screw shield and prototyping shield. This Proto Screw shield offers a better way to do prototyping. The Screw terminal can be screwed directly to the terminal on the thread and is reliable and convenient. It can be plugged into the Arduino controller. You can use this shield to save yourself from the bad port connection. Feel secure with this arduino-compatible screw shield. The prototyping shield provides a fast prototpying area for projects. It features a LED (D13) and...

This is a very simple board that takes a 6-12V input voltage and outputs a selectable 5V or 3.3V regulated voltage. All headers are 0.1" pitch for simple insertion into a breadboard. It can be...

This is a very simple board that takes a 6-12V input voltage and outputs a selectable 5V or 3.3V regulated voltage. All headers are 0.1" pitch for simple insertion into a breadboard. It can be either powered from 6-12 DC2.1 power jack or from USB power.  The maximum current it can provide is 500mA.  Specification Input voltage: 6-12V (Power Jack) 5V (USB) Output voltage:3.3V/5V Output current:500mA On/Off switch Power status LED Pin Head 5/3.3V output Central positive DC2.1 power...

This Relay Shield for Arduino acts like a switch. It is commonly used to control anything over 5V such as lamps, water pumps and garage doors. One of the most interesting projects for your boards is...

This Relay Shield for Arduino acts like a switch. It is commonly used to control anything over 5V such as lamps, water pumps and garage doors. One of the most interesting projects for your boards is perhaps being able to control High power devices like Lamps, water pumps, garage doors and so on. But interfacing with high power and AC is quite a dangerous task when building the circuitry. Relays allow for interfacing an external electrical circuit like a switch. With relays you can now connect...

The XBee USB Adapter V2 is an update version from DFRobot. It features an Atmega8U2 programmed as a USB-to-serial converter, the same chip found on the Arduino Uno. The Atmega8U2 firmware uses the...

The XBee USB Adapter V2 is an update version from DFRobot. It features an Atmega8U2 programmed as a USB-to-serial converter, the same chip found on the Arduino Uno. The Atmega8U2 firmware uses the standard USB COM drivers, and no external driver is needed. However, on Windows, a .inf file is required. It's compatible with all the products using XBee socket. It provides a faster and stable wireless communication for your projects. The DFRobot Xbee USB adapter is used for the XBee module...

NEW VERSION! This is the upgraded DFRduino Mega 2560 V3.0 which is now fully compatible with Arduino Mega 2560 R3. The Arduino Mega is a microcontroller board based on the ATmega2560. It has 54...

NEW VERSION! This is the upgraded DFRduino Mega 2560 V3.0 which is now fully compatible with Arduino Mega 2560 R3. The Arduino Mega is a microcontroller board based on the ATmega2560. It has 54 digital input/output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header and a reset button. It contains everything needed to support the microcontroller; Connect it to a computer...

This is a waterproofed version of the DS18B20 Temperature sensor. Handy for when you need to measure something far away, or in wet conditions. While the sensor is good up to 125°C the cable is...

This is a waterproofed version of the DS18B20 Temperature sensor. Handy for when you need to measure something far away, or in wet conditions. While the sensor is good up to 125°C the cable is jacketed in PVC so we suggest keeping it under 100°C. Because they are digital, you don't get any signal degradation even over long distances! The DS18B20 provides 9 to 12-bit (configurable) temperature readings over a 1-Wire interface, so that only one wire (and ground) needs to be connected...

CheapDuino is the most affordable Arduino compatible processor in the world. The price for each cheapDuino is almost 1/5 price of the Arduino UNO R3. It aims to provide an extremely low-cost...

CheapDuino is the most affordable Arduino compatible processor in the world. The price for each cheapDuino is almost 1/5 price of the Arduino UNO R3. It aims to provide an extremely low-cost solution for any disposable projects, such as DIY projects, workshop, gifts projects, E-Textiles and education. For those students from second or third world countries who can not afford the official Arduino, cheapduino opens the door to the physical world. The cheapDuino is integratd with an ATmega8...

This is a 4.8-46V, 2A Dual Motor Controller which is the revised version of the DF-MDV1.0. Its performance has been improved greatly. It can bear larger current due to the increased heat-sink...

This is a 4.8-46V, 2A Dual Motor Controller which is the revised version of the DF-MDV1.0. Its performance has been improved greatly. It can bear larger current due to the increased heat-sink dissipation. It is easy to control, using LGS's outstanding high-power motor driver chip, the L298N. This chip allows for direct drive of two bi-directional DC motors, and incorporates high-speed short diodes for protection. Drive current up to 2A per motor output. The driver uses a broad-brush design to...

Arduino product family is a great learning platform for electronics, programming and robotics. But most projects at some point require mobility. This Arduino motor shield allows for motor control...

Arduino product family is a great learning platform for electronics, programming and robotics. But most projects at some point require mobility. This Arduino motor shield allows for motor control with Arduino right away. Stack up this shield on your controller and drive 2 DC motors with higher power requirements. Depending on the motor of choice, you can make it fast or handle a higher payload. This Arduino Motor Shield (2A) uses L298P chip which allow to drive two 7-12V DC motors with maximum...

This is a very small breadboard with 170 tie points. This bread board is compatible with the Arduino Proto Shield. Strong self-adhesive backing. Measures 1.8"x1.4".You also have choices of different...

This is a very small breadboard with 170 tie points. This bread board is compatible with the Arduino Proto Shield. Strong self-adhesive backing. Measures 1.8"x1.4".You also have choices of different colors. |Specification| 170 tie point breadboard 17 x 5 x 2 points Adhesive backing Black |ShippingList| Black 170 tie point bread board &;times;1

This is a medium size breadboard with 600 tie points. It has strong, self-adhesive backing. It is ideal for high frequency and low noise circuits. |Specification| Size:170*65mm (6.7x2.6 in) Suitable...

This is a medium size breadboard with 600 tie points. It has strong, self-adhesive backing. It is ideal for high frequency and low noise circuits. |Specification| Size:170*65mm (6.7x2.6 in) Suitable for 0.3-0.8 mm (0.01x0.03 in) wire|ShippingList| Medium Bread Board Self Adhsive x1

The digital sensor cables are especially designed for our popular IO Expansion shield and sensors. It connects most of our digital sensor to the IO board. This price includes 10 pieces of...

The digital sensor cables are especially designed for our popular IO Expansion shield and sensors. It connects most of our digital sensor to the IO board. This price includes 10 pieces of cables.|Specification| Length:30cm (12 in) Maximum voltage:&;lt;50V Maximum current:&;lt;1000mA One Servo Type connector with Signal, GND PWR. One 3 Pin JST connector Red: PWR, Black:GND; Green: Signal|ShippingList| Digital Sensor Cable for Arduino (10 Pack) x1 ...

This is a TT Micro DC Geared Motor with Back Shaft working at 6V with 160rpm. The TT motor series the most popular DC motors for DIY enthusiasts. It is designed to easily incorporate the DFRobot...

This is a TT Micro DC Geared Motor with Back Shaft working at 6V with 160rpm. The TT motor series the most popular DC motors for DIY enthusiasts. It is designed to easily incorporate the DFRobot Encoder. These motors are inexpensive, small, easy to install, and ideally suited for use in a mobile robot. The DFRobot ROMEO microcontroller is able to complete the closed-loop PID making use of the Gravity:TT Motor Encoders Kit. We recommend this rubber wheel for this motor. |Specification|Electrical...

This cable is especially designed for Interface shield,shift out module, SPI Led and SPI LCD module. It is has a female 2&;times;3 IDC connector on each end that is designed to plug into a 0.100"...

This cable is especially designed for Interface shield,shift out module, SPI Led and SPI LCD module. It is has a female 2&;times;3 IDC connector on each end that is designed to plug into a 0.100" (2.54 mm) 2&;times;3 shrouded box header. |Specification| Length:20cm (7.9&;#39;&;#39;) Female/Femal, IDC 2x3 Connector|ShippingList| Cable for Shiftout x1

This battery holder can hold 6 AA battery which can make 7.2 V rechargeable battery pack from NiMH / NiCd cells or 9V battery pack from alkaline cells.It comes with a 6" Red & Black Wires with side...

This battery holder can hold 6 AA battery which can make 7.2 V rechargeable battery pack from NiMH / NiCd cells or 9V battery pack from alkaline cells.It comes with a 6" Red & Black Wires with side by side & stack connection. |Specification| Cell Quantity: 6 Battery type: AA Storage temperature: 25&;#39;C (77F, RoomTemperature) Max Operate temperature: 80&;#39;C (176F)|ShippingList| 6xAA battery holder (double layer) x1 ...

This is a 8-pin female header which is used on Arduino board. |ShippingList| 8 Pin Header x10

This is a 8-pin female header which is used on Arduino board. |ShippingList| 8 Pin Header x10

These are a longer version of our standard break away headers. They are 10mm long which allows you use them socket to socket. The plastic separator can be slid up or down to accommodate your needs....

These are a longer version of our standard break away headers. They are 10mm long which allows you use them socket to socket. The plastic separator can be slid up or down to accommodate your needs. 40 pins that can be cut to any size. Used with custom PCBs or general custom headers. It is used on Arduino Ethernet Shield.|ShippingList| 40 Pin Header x10

These are standard alligator to alligator (crocodile) clip test cables. The alligator clip allow you attach the test point without hold the cables which is really handy. The clip is strong and...

These are standard alligator to alligator (crocodile) clip test cables. The alligator clip allow you attach the test point without hold the cables which is really handy. The clip is strong and grippy. |Specification| Contains two of each: Black, red, white, green, and yellow. 22 gauge heavy insulation copper wire alligator clips at both ends 30cm(11.8&;#39;&;#39;) in length|ShippingList| 10 piece set, Color Coded may vary ...

It comes with 20 of each value: 1R 1.2R 1.5R 1.8R 2R 2.2R 2.7R 3R 3.3R 3.9R 4.7R 5.1R 6.2R 6.8R 8.2R 10R 12R 15R 18R 20R 22R 27R 30R 33R 39R 47R 51R 62R 68R 82R 100R 120R 150R 180R 200R 220R 270R...

It comes with 20 of each value: 1R 1.2R 1.5R 1.8R 2R 2.2R 2.7R 3R 3.3R 3.9R 4.7R 5.1R 6.2R 6.8R 8.2R 10R 12R 15R 18R 20R 22R 27R 30R 33R 39R 47R 51R 62R 68R 82R 100R 120R 150R 180R 200R 220R 270R 300R 330R 390R 470R 510R 620R 680R 820R 1K 1.2K 1.5K 1.8K 2K 2.2K 2.7K 3K 3.3K 3.9K 4.7K 5.1K 6.2K 6.8K 8.2K 10K 12K 15K 18K 20K 22K 27K 30K 33K 39K 47K 51K 62K 68K 82K 100K 120K 150K 180K 200K 220K 270K 300K 330K 390K 470K 510K 620K 680K 820K 1M 1.2M 1.5M 1.8M 2M 2.2M 3.3M 3.9M 4.7M 5.1MNOTE: As this...

Jumper wires are one of the most important gear component for the tinkerer. Often understimated, but one of the first things to miss. If you are starting to assemble your tinker gear and wondering...

Jumper wires are one of the most important gear component for the tinkerer. Often understimated, but one of the first things to miss. If you are starting to assemble your tinker gear and wondering if this is really needed, doubt not, this is at some point or another always used. Wire or pieces or wire are basic, even for the non-often tinkerers. Jumper wires are not just fitted for prototyping but also a resource for repurposing. You can cut them and add new headers, or mix them up and connect...

Introduction Standard 16x2 character LCD display. It has a basic 16 character by 2 line display with a green background with gold characters. Please note: Yes, that's not it in the pic - but...

Introduction Standard 16x2 character LCD display. It has a basic 16 character by 2 line display with a green background with gold characters. Please note: Yes, that's not it in the pic - but you get the idea. :) Specification Supply voltage:5V Documents Datasheet ...

This simple cable has so many uses! Plug a 9V battery into one end and connect the other end to anything with a 5.5x2.1mm, center-positive barrel jack.Use this cable to battery-power any device that...

This simple cable has so many uses! Plug a 9V battery into one end and connect the other end to anything with a 5.5x2.1mm, center-positive barrel jack.Use this cable to battery-power any device that needs 9V and has an on-board barrel jack - it works great for Arduinos, development boards, evaluation boards, and more!|ShippingList| ?9V to Barrel Jack Adapter x1

This ball caster used for MiniQ robot is a white ABS housing, a 3/8" diameter metal ball, two spacers (1/16" and 1/8" thick), and two #2 screw sets.The total height of this ball caster is 0.4" with...

This ball caster used for MiniQ robot is a white ABS housing, a 3/8" diameter metal ball, two spacers (1/16" and 1/8" thick), and two #2 screw sets.The total height of this ball caster is 0.4" with no spacers. You can also adjust the height by adding the spacers.The ball caster is used in our widely popular MiniQ sereis. |ShippingList| Ball caster x1 Screws x2

Immersible pump &; Water tube Introduction This immersible pump can be used to water your plants, make a fountain or waterfall, even change your fish tank wter.It works quietly with the sound level...

Immersible pump &; Water tube Introduction This immersible pump can be used to water your plants, make a fountain or waterfall, even change your fish tank wter.It works quietly with the sound level under 30db. The pump has a filter inside as well as a suction cup which can help stick it to smooth surfaces tightly.   Note: This pump is intended for use UNDER the water ONLY!     Application   It’s widely used for solar products, fountain, rockery?air-Conditioner,...

This is a 2 wire (+-) blower fan for all your cooling needs. |Specification| Supply voltage: DC 12V Current consumption: 0.3A|ShippingList| Blower Fan x1 ...

This is a 2 wire (+-) blower fan for all your cooling needs. |Specification| Supply voltage: DC 12V Current consumption: 0.3A|ShippingList| Blower Fan x1

This is a black braided cable guide. The braid provides some rigidity to the cables, also, it can be expanded by compressing it which will allow many more cables to fit inside. |Specification|...

This is a black braided cable guide. The braid provides some rigidity to the cables, also, it can be expanded by compressing it which will allow many more cables to fit inside. |Specification| Color: Black Length: 1.25m (49.21") Inner diameter: 10mm (0.39") |ShippingList| Braided cable guide (1.25 meter)

This is a white spiral cable guide. This spiral makes it very easy to control your cables after they&;#39;ve already been plugged in, or when you have many cables going to differnet places. NOTE:...

This is a white spiral cable guide. This spiral makes it very easy to control your cables after they&;#39;ve already been plugged in, or when you have many cables going to differnet places. NOTE: Longer sleeving is available upon request. Please contect Sales for details. |Specification| Color: white Length: 1m(39.37") inner diameter: 12mm(0.47") |ShippingList| Spiral cable guide x1 ...

This kit includes JST XHP-2, XHP-3 and XHP-4 housing (20 units each), through-hole type shrouded header (20 units each) and crimp contact (100 units). |Specification| Current rating:3A AC,DC (AWG...

This kit includes JST XHP-2, XHP-3 and XHP-4 housing (20 units each), through-hole type shrouded header (20 units each) and crimp contact (100 units). |Specification| Current rating:3A AC,DC (AWG #22) Voltage rating:250V AC,DC Temperature range?-25? to +85??including temperature rise in applying electrical current? Contact resistance?Initial value/10m &;Omega; max. After environmental testing/20m &;Omega; max. Insulation resistance?1000M &;Omega; min. Withstanding voltage?1000V AC/minute...

This box of grease is very small, light and easy to carry. It can be uesd in many places. It is suitable for the condition of light load or high speed plastic gear, plastic parts, nylon retainer...

This box of grease is very small, light and easy to carry. It can be uesd in many places. It is suitable for the condition of light load or high speed plastic gear, plastic parts, nylon retainer bearing lubrication, protection and noise reduction. You will need it for your robot and 3D Printer. |Specification| Net Weight : 5g|ShippingList| Grease(5g) x1

EcoDuino is evolving. Now the EcoDuino has a new enclosure. It is protected from water splashes, so it is safe to use beside your plants. The EcoDuino now sports an Atmega32U4 which eliminates the...

EcoDuino is evolving. Now the EcoDuino has a new enclosure. It is protected from water splashes, so it is safe to use beside your plants. The EcoDuino now sports an Atmega32U4 which eliminates the requirement of an adapter. And sketches can simply uploaded via Micro USB just like Arduino Leonado. Another improvement is that the DS18B20 sensor is now directly supported. EcoDuino is designed by DFRobot to help you grow plants. By using a series of microcontrollers, sensors and actuators, the...

If you want to start playing with sensors, this sensor kit for arduino will be the perfect choice for you to get started. It comes with bundle of the most popular DFRobot sensors such as light...

If you want to start playing with sensors, this sensor kit for arduino will be the perfect choice for you to get started. It comes with bundle of the most popular DFRobot sensors such as light sensors, gas sensors, sound sensors, touch sensors, distance sensor, accelerometer and lots more which gives unlimited possibility to sense the physical world on your embedded devices. The wiki for these sensors and devices makes it easy to start learning. So save by purchasing them together and start...

URM37 V4.0 Arduino Ultrasonic Sensor comes with temperature compensation which provides better distance measurement accuracy. It is very unique feature in the industry. URM37 V4.0 Arduino Ultrasonic...

URM37 V4.0 Arduino Ultrasonic Sensor comes with temperature compensation which provides better distance measurement accuracy. It is very unique feature in the industry. URM37 V4.0 Arduino Ultrasonic Sensor offers output modes: analog output, switch, serial (TTL and RS232 level optional) and PWM. With analog mode, the sensor outputs voltage which is proportional with distance, it can be connected to Arduino, Raspberry Pi and LattePanda(windows 10 development board).With switch mode, the...

This is a line tracking (following) sensor to guide your robot by telling white from black quickly and accurately. It is commonly used in arduino robot project, and probably is the best line...

This is a line tracking (following) sensor to guide your robot by telling white from black quickly and accurately. It is commonly used in arduino robot project, and probably is the best line following sensor in the market.Line following is the most basic function of smart mobile robot. As you can see line tracking robot one of the easiest ways for a robot to successfully and accurately navigate. We designed this new generation of line tracking sensor to be your robot's powerful copilot all the...

This is a simple to use arduino motion sensor. Power it up and wait 1-2 seconds for the sensor to get a snapshot of the still room. If anything moves after that period, the 'alarm' pin will go low....

This is a simple to use arduino motion sensor. Power it up and wait 1-2 seconds for the sensor to get a snapshot of the still room. If anything moves after that period, the 'alarm' pin will go low. This sensor checks for infrared heat in it's detecting angle. Human body, pets and several other things emit energy that the sensor is looking for, it compares with the snapshot and if there is a recent change it triggers.Get on with your Home alarm security audit gear and experiment with this...

This is an Arduino infrared distance sensor. It has an adjustable detection range, 3cm - 80cm. It is small, easy to use, assemble, and inexpensive. Useful for robotics, interactive media, industrial...

This is an Arduino infrared distance sensor. It has an adjustable detection range, 3cm - 80cm. It is small, easy to use, assemble, and inexpensive. Useful for robotics, interactive media, industrial assembly line, etc. Infrared wave length is part of the Sun's natural light spectrum. While is a nice fit for indoor projects, outdoors with plenty of sun light and reflective surfaces on it's sight is not adviced. It's incredibly repurposable and can be used for a lot of different projects. The...