Products 1-30 of 30
Show
2.4GHz 6dBi Antenna with IPEX Connector
OOD!
Price: $8.45
View
Availability: Back Order
DFRobot Item #: FIT0505 -

This is an omni-directional antenna with an IPEX connector. Its working frequency is 2.4GHz which meets most requirements of Wi-Fi devices. With 6dBi high gain, it offers robust signal reception and transmission. It is ideal for use with a LattePanda single board computer|Specification| Frequency: 2.4 GHz Gain: 6dBi Cable Length: 15cm Interface: IPEX MHF1 Supports LattePanda Height: 170 mm/ 6.7 inches Weight: 18g|ShippingList| 2.4GHz 6dBi Antenna with IPEX connector x 1 ...

2.4GHz Antenna - Adhesive (U.FL Connector)
OOD!
Price: $6.81
View
Availability: Back Order
Sparkfun Item #: WRL-11320 -

"This adhesive, omni-directional antenna is perfect for situations when you’re trying to get a signal out from a transmitter that you’ve jammed down into an enclosure. Operating on the 2.4GHz band, it works great for WiFi, Bluetooth or ZigBee. Just connect the antenna using the attached u.fl connector and then peel and stick! Dimensions: 41 x 30mm, 350mm cable Features: Type: Omni-Directional Dual Frequency Range: 2300 to 3800MHz & 5150 to 5875MHz Impedance: 50 Ohm Maximum...

2.4GHz Ceramic Chip Antenna
OOD!
Price: $3.40
View
Availability: Back Order
Sparkfun Item #: WRL-00144 -

"2.4GHz ceramic chip antennas. Very small antennas that work nicely with the Nordic ICs. Don’t expect these little guys to perform as well as their ~2" rubber duck counter parts, but then again, these will squeeze onto any PCB layout. Dimensions: 2.2x6.5mm Documents: chip-antenna-2.4ghz.pdf"

2.4GHz Duck Antenna RP-SMA
Price: $9.14
View
Availability: Stocked
Sparkfun Item #: WRL-00145 -

"2.4GHz Duck Antenna 2.2dBi with Reverse Polarized - SMA RF connector. Perfect for prototyping with our RF ICs. 50 ohm impedance. 4" long. The FCC is moving towards Part 15 compliance. All this means is that all the SMA RF connectors are changing gender. Really annoying for those of us who need to mate an antenna to an RF device. The FCC gender change was instituted to prevent home users from damaging RF equipment (think home WiFi) when screwing on an antenna. If all antennas are female, there...

2.4GHz Duck Antenna RP-SMA - Large
Price: $11.44
View
Availability: Back Order
Sparkfun Item #: WRL-00558 -

"Need range? 2.4GHz Large Duck Antenna 5dBi with Reverse Polarized - SMA RF connector. Perfect for prototyping with our RF ICs. 50 ohm impedance. This antenna mates nicely with the Reverse Polarized SMA Connector. Dimensions: 0.5x7.7" Documents:Datasheet"

900MHz Duck Antenna RP-SMA
OOD!
Price: $9.14
View
Availability: Back Order
Sparkfun Item #: WRL-09143 -

"900/1800 MHz Duck Antenna 2dBi with regular RP-SMA RF connector. Perfect for use with the XBee 900MHz units. 50 ohm impedance. 105mm long. The FCC is moving towards Part 15 compliance. All this means is that all the SMA RF connectors are changing gender. Really annoying for those of us who need to mate an antenna to an RF device. The FCC gender change was instituted to prevent home users from damaging RF equipment (think home WiFi) when screwing on an antenna. If all antennas are female,...

915MHz LoRa Antenna RP-SMA - 1/2 Wave 2dBi
OOD!
Price: $10.21
View
Availability: Back Order
Sparkfun Item #: WRL-14876 -

"Increase your range with this ½ wave duck antenna. Designed for 860 to 960MHz it is ideal for distant LoRa nodes. Utilizes an RP-SMA connector and is 200mm long. Documents: 915MHz ½ Wave RP-SMA Antenna Datasheet "

915MHz LoRa Antenna RP-SMA - 1/4 Wave 2dBi
OOD!
Price: $9.14
View
Availability: Back Order
Sparkfun Item #: WRL-14875 -

"A small ¼ wave rubber duck antenna for LoRa or other 860-960MHz communication. Antenna has a center frequency of 915MHz and utilizes an RP-SMA connector. Gain is 2dBi with an overall length of 110mm."

915MHz LoRa Fiberglass Antenna Type N - 6dBi
OOD!
Price: $59.57
View
Availability: Back Order
Sparkfun Item #: WRL-14868 -

"If you need maximum distance for your LoRa project you need this incredibly durable, outdoor antenna with 6dBi gain. This 915MHz antenna is 40cm / 15.75" long and includes hardware for pole mounting. Made of fiberglass and aluminum this antenna is ideal for heavy-duty and high-power LoRa base stations but can be used with LoRa nodes as well. Antenna has a type N male termination. When mounted vertically this shrouded connector helps prevent against water and weather build-up on the threads....

Antenna GPS 3V Magnetic Mount SMA
OOD!
Price: $14.89
View
Availability: Back Order
Sparkfun Item #: GPS-00464 -

"Magnet mount antenna for GPS modules operating at 3V. Designed for use with automobiles - the magnet will hold the antenna in place at speeds greater than 100mph. 5 meter cable terminated with standard male SMA connector. Check out our GPS buying guide! Features: Gain 26dB VSWR <2.0 Voltage 3.3V +/- 0.5V Current 12mA Weight 50g Documents: Datasheet" ...

Antenna GPS Chip-Scale
Price: $1.73
View
Availability: Back Order
Sparkfun Item #: GPS-09131 -

"That is a GPS chip antenna. Itty-bitty! And we were just as surprised when it picked up just as many satellites as the larger ceramic antennas. The PDOP and VDOP (dilution of precision) of these chip antennas are greater than their ceramic siblings and the gain is not as great (to be expected), but heck, if you can get a lock with this little guy, who cares? Note: This is just a GPS antenna and is not a complete GPS module. For a complete module, check out our GPS category. Check out our GPS...

Antenna GPS Embedded SMA
Price: $14.47
View
Availability: Stocked
Sparkfun Item #: GPS-00177 -

"Embedded antenna for small, mobile applications. Basic unpackaged antenna with LNA. 5inch cable terminated with standard male SMA connector. Match it with any SMA interface cable to create a truly small GPS prototype! This unit works very well out of the box, but the fully packaged antennas have better strain relief where the SMA cable meets the antenna housing. If you plan on using this antenna in a vibration intensive application, we recommend you reinforce the connection with epoxy or Shoe...

Built-in Spring GSM Antenna
OOD!
Price: $5.00
View
Availability: Back Order
DFRobot Item #: FIT0454 -

This is a small built-in spring GSM antenna with IPX connector. Its working frequency is 900/1800 MHz which meets most requirements of GSM applications. Its very compact size makes it easy to carry and use.Compatible With:SIM 908 GPS/GPRS/GSM Shield For ArduinoSIM800H GPRS IOT Shield For Arduino|Specification| Signal gain: 2dBi Frequency Range: 824-960/1710-1990 MHz Length: Black:5.1cm; Grey:3cm Connector: IPX/UF.L Cable type: RG1.13 Color: Grey and Black|ShippingList| Built-in Spring GSM...

Interface Cable MMCX to SMA
OOD!
Price: $10.29
View
Availability: Back Order
Sparkfun Item #: GPS-00285 -

"SMA to MMCX Connector. Adapts MMCX jack to a standard SMA bulkhead. This cable interfaces to the GM862 Cellular modules and the PG31 GPS module. Length: 6" (6.7" including the MMCX and SMA connectors)"

Interface Cable N to RP-SMA Cable - 1m
OOD!
Price: $10.21
View
Availability: Back Order
Sparkfun Item #: CAB-14911 -

"This connector cable interfaces N type female to RP-SMA male. Primarily used to connect our larger 915MHz LoRa antenna to RP-SMA connections but can be used on other devices up to 3GHz. Cable type is RG316. Length is 1m."

Interface Cable RP-SMA to U.FL
Price: $5.69
View
Availability: Stocked
Sparkfun Item #: WRL-00662 -

"This connector cable interfaces UFL RF connectors to RP-SMA antennas. Use it to attach any standard RP-SMA 2.4GHz antenna to the our WiFly Shield. Dimensions: 4" Length Documents: Datasheet RF Connector Buying Guide "

Interface Cable SMA to U.FL
OOD!
Price: $5.69
View
Availability: Stocked
Sparkfun Item #: WRL-09145 -

"This is a 4" connector cable that interfaces U.FL RF connectors to regular SMA connectors. Documents: Datasheet RF Connector Buying Guide "

Pycom LoRa and Sigfox Antenna Kit
OOD!
Price: $20.34
View
Availability: Back Order
Sparkfun Item #: WRL-14676 -

"If you intend on using the LoRa or Sigfox connectivity on the LoPy4 you are going to need to connect a special antenna before beforehand otherwise you risk damaging the device. Luckily, with this Antenna Kit from Pycom, you won’t need to worry about hurting your fancy LoPy4. This universal LoRa and Sigfox Antenna Kit can also be used with LoPy, SiPy, and FiPy IoT development boards on top of the LoPy4. Included in this kit is a tilt swivel ½ wave whip antenna with a male RP-SMA...

Quad-band Cellular Antenna SMA
Price: $11.44
View
Availability: Stocked
Sparkfun Item #: CEL-08347 -

"This high gain, 7.75" antenna is perfect for AVL applications where cellular reception is a must. Connector is regular SMA so don’t confuse it with 2.4GHz antennas. Specifications: GSM/850E : 824 to 894MHz GSM : 880 to 960MHz DCS : 1710 to 1880MHz PCS : 1850 to 1990MHz Documents: Datasheet "

Quad-band Cellular Duck Antenna SMA
Price: $9.14
View
Availability: Stocked
Sparkfun Item #: CEL-00675 -

"This is a fantastic find for SFE. A small, high-quality, quad-band, standard SMA terminated, cellular antenna. Specifications: GSM/850E : 824 to 894MHz GSM : 880 to 960MHz DCS : 1710 to 1880MHz PCS : 1850 to 1990MHz Documents:GSM Antenna 850-1900MHz"

Reverse Polarized SMA Connector
OOD!
Price: $2.24
View
Availability: Back Order
Sparkfun Item #: WRL-00592 -

"PCB edge mount Reverse Polarized - SMA RF connector. Perfect for prototyping with our RF ICs. This is a standard edge connector. The thickness between pins is 0.063" so that it can slide sideways onto a PCB. See the mechanical drawing to create your footprint. The FCC is moving towards Part 15 compliance. All this means is that all the SMA RF connectors are changing gender. Really annoying for those of us who need to mate an antenna to an RF device. The FCC gender change was instituted to...

RockBLOCK External Patch Antenna
OOD!
Price: $93.61
View
Availability: Back Order
Sparkfun Item #: WRL-14580 -

"The RockBLOCK External Patch Antenna is a high-performance magnetic mount antenna designed specifically to communicate efficiently with the Iridium® Satellite Communication system. This antenna utilizes the Taoglas expertise in ceramics by incorporating a ceramic patch tuned specifically for the antenna environment, giving greater stability. The antenna housing is strong, corrosion-proof and waterproof to IP67. The magnetic mount allows for easy installation and removal between vehicles...

RPSMA Male to SMA Female Adapter
OOD!
Price: $2.55
View
Availability: Back Order
Sparkfun Item #: WRL-09232 -

"This is an adapter that converts an RP-SMA board to an SMA antenna. The adapter will connect to any of our 2.4GHz wireless boards (Bluetooth, Nordic, or XBee) or interface cables and will allow you to use an antenna/cable with an SMA connection. You should not need this adapter with any of our antennas or dev boards. These adapters are listed only to help SparkFun users that have rare or odd antenna coupling needs. Be sure to check out the SMA connector tutorial here for more information on...

SMA Connector
Price: $2.24
View
Availability: Back Order
Sparkfun Item #: WRL-00593 -

"PCB edge mount - SMA RF connector. Perfect for prototyping with the GPS and Cellular devices that require an antenna connection. These connectors have a female signal pin and will correctly mate with the original SMA type antennas. Documents: Datasheet SMA Tutorial "

SMA Male to RPSMA Male Adapter
OOD!
Price: $2.55
View
Availability: Back Order
Sparkfun Item #: WRL-09233 -

"This is an inner thread (outer nut) adapter that will connect to any of our wireless boards or interface cables and allow you to use an antenna/cable that has an outer thread configuration. You should not need this adapter with any of our antennas or dev boards. These adapters are listed only to help SparkFun users that have rare or odd antenna coupling needs. Be sure to check out the SMA connector tutorial here for more information on SMA connectors. Supported Connections: Any RP-SMA or SMA...

Telescopic Antenna SMA - 300 MHz to 1.1 GHz (ANT700)
OOD!
Price: $34.04
View
Availability: Back Order
Sparkfun Item #: WRL-13982 -

"This ANT700 is a telescopic antenna designed for operation from 300 MHz to 1.1 GHz with a total length that is configurable from 9.5 cm to 24.5 cm. Each ANT700 is constructed of stainless steel and features an SMA male connector, rotating shaft, and adjustable elbow. The ANT700 is a 50 Ohm antenna designed to match HackRF One. It is the perfect first antenna for general purpose use with HackRF One, but we won’t stop you from using it with different projects! Documents: Product Page " ...

Telescopic Antenna SMA - 75 MHz to 1 GHz (ANT500)
OOD!
Price: $42.55
View
Availability: Back Order
Sparkfun Item #: WRL-13002 -

"This ANT500 is a telescopic antenna designed for operation from 75 MHz to 1 GHz with a total length that is configurable from 20 cm to 88 cm long. Each ANT500 is constructed of stainless steel and features an SMA male connector, rotating shaft, and adjustable elbow. The ANT500 is a 50 ohm antenna designed to match HackRF One. It is the perfect first antenna for general purpose use with HackRF One but we won’t stop you from using it with different projects! Documents: Product Video " ...

U.FL SMD Connector
OOD!
Price: $1.73
View
Availability: Back Order
Sparkfun Item #: WRL-09144 -

"Itty-bitty U.FL SMD connector. Great for tight PCB layouts that require antenna connections. Documents: Datasheet "

UHF RFID Antenna (TNC)
OOD!
Price: $44.25
View
Availability: Back Order
Sparkfun Item #: WRL-14131 -

"This is your solution when you absolutely, positively need to get the most out of an antenna for your next RFID project. This ultra high-frequency (UHF) RFID Antenna boasts a frequency range of 860-960 MHz with a gain of 6dBi. This is the same external antenna we use for our Simultaneous RFID Reader due to its high-quality features. Each UHF RFID Antenna is terminated with a 30cm long TNC Female RP cable and also includes all the mounting gear you’ll need to attach it to any surface or...

XBee-PRO 900HP S3B RPSMA Antenna
OOD!
Price: $101.79
View
Availability: Back Order
DFRobot Item #: TEL0021 -

Digi International XBee-PRO 900HP RF Modules enjoys proven reputation in wireless devices connectivity. They benefit from the DigiMesh networking protocol, feature dense network operation and support for sleeping routers. and are also available in a proprietary point-to-multipoint configuration. Supporting RF line-of-sight ranges up to 9 miles (with high-gain antennas), and data rates of up to 200Kbps, these modules are ideal for extended-range applications requiring increased data...