We are still taking orders but are unable to ship items this week. All items purchased (excluding OOD) will be shipped on 21st August 2017.


Products 1-48 of 56
Show
40 Pin Dual Female Splittable Jumper Wire - 200mm
Price: $5.60
View
Availability: Stocked
Elecrow Item #: EL-PCW02040A -

This is a splittable 40 pin 20mm length dual female jumper wire for 2.54mm, it is very flexible, can be used at bread board or other places need connection. it is able to transformed from 1-20 pin jumper wire.

40 Pin Male - Female Splittable Jumper Wire - 200mm
Price: $6.53
View
Availability: Stocked
Elecrow Item #: EL-PCW02040P -

This is a splittable 40 pin 20mm length male - female jumper wire for 2.54mm, it is very flexible, can be using at bread board or other place need connection. it is able to transformed from 1-40 pin jumper wire. There also have 40pin wire which have same specification in here. ...

40 Pin Dual Male Splittable Jumper Wire - 200mm
Price: $6.53
View
Availability: Stocked
Elecrow Item #: EL-PCW40220P -

This is a splittable 40 pin 20mm length dual male jumper wire for 2.54mm, it is very flexible, can be using at bread board or other place need connection. it is able to transformed from 1-40 pin jumper wire. There also have 20 pin wire which have same specification in here. ...

Basic Bread Board With Slot - 8.3*5.5 cm
Price: $5.37
View
Availability: Stocked
Elecrow Item #: EL-PBB08555W -

This is a half size breadboard with dimension 8.3*5.5 cm. It has two power rails on the sides to allow more than one power level. In addition, it can make the breadboard as thin as 3.5cm and stick it onto an Arduino protoshield by pull the power rails off easily. With a total of 400 tie in points, all pins are spaced by a standard 0.1"(2.54mm). It has a self-adhesive on the back and also interlocking parts, so you can hook as many together as you\'d like.Features400 Tie PointSelf adhesiveCan...

2.54mm FEMALE-MALE JUMPER WIRE - 300MM (40PCS PACK)
Price: $5.83
View
Availability: Stocked
Elecrow Item #: EL-PCW00012F -

This is a pack including 40pcs of 300mm female-male DuPont jumpers. With these wire, you can easily connect electronic components to breadboard to make your project with these jumper wires.SpecificationWire Qty:40Length:300mmConnector Type:Female - MaleColor: Combined

Breadboard Jumper Wire 60pcs Pack
Price: $5.83
View
Availability: Stocked
Elecrow Item #: EL-PCW06500D -

This Breadboard jumper wire pack include 65pcs dual-male jumpers, including 4 different length:250mm 4pcs,200mm 4pcs,165mm 8pcs and 110mm 49, It is very flexible for breadboards.

50gm Polymorph Moldable Plastic
Price: $5.75
View
Availability: Stocked
MK-Misc Item #: polymorph -

50gm Polymorph Moldable Plastic Polymorph is a plastic that melts at around 60 degrees Celsius and becomes mouldable and easily shaped. All you need to do is pop some of the granules into hot water or heat them with a hair dryer and once they reach 60 degree you can shape them easily with your hands or put it into a mould ready to make complex shapes. If you make a mistake just put it back into the water and start again. This stuff really changed the way we tinkered and has been a life saver...

40 Pin Dual Female Splittable Jumper Wire - 300mm
Price: $6.53
View
Availability: Stocked
Elecrow Item #: EL-PCW03040A -

This is a splittable 40 pin 30mm length dual female jumper wire for 2.54mm, it is very flexible, can be used at bread board or other places that need connection. it is able to transform to 1-40 pin jumper wire.

Basic Bread Board With Slot - 16.5*5.5 cm
Price: $10.50
View
Availability: Stocked
Elecrow Item #: EL-PBB01655W -

This is a full size breadboard with dimension 16.5*5.5 cm. It has two power rails on the sides to allow more than one power level.With a total of 830 tie in points, all pins are spaced by a standard 0.1"(2.54mm). It has a self-adhesive on the back and also interlocking parts, so you can hook as many together as you\'d like.Features830 Tie PointSelf adhesiveCan be interlocked2 power lanesDimensions: 16.5 * 5.5 cm ...

Screw Shield
Price: $13.25
View
Availability: Stocked
Elecrow Item #: EL-MCS01110 -

The Screw Shield extends all pins of the Arduino out to 3.5mm pitch screw terminals. It also has a lot of the utility provided by Arduino Protoshield, including: a large prototyping space of both connected and unconnected 0.1" spaced through-holes, a couple 5V and GND busses, a reset button, and a 5mm green LED. The Screw terminal can be screwed directly to the terminal on the thread and is reliable and convenient. It can be plugged into the Arduino controller. You can use this shield to save...

Mini Bread Board 4.5x3.5cm - Clear
Price: $2.33
View
Availability: Stocked
Elecrow Item #: EL-PBB05545T -

The dimension of this mini breadboards is 45 × 35 ×9 mm\u010f\u017a\u0152it have a self-adhesive backing and 2 x 17 rows of interconnected pins (5 per row) - 170 pins in total. Besides, it is able to combine several mini boards with slot. This board is very suit for those project that need compact dimension.Features170 Tie PointSelf adhesiveCan be interlockedDimensions: 45 * 35 mm ...

Screw Terminals 5mm Pitch - 2Pin (5pcs Pack)
Price: $2.10
View
Availability: Stocked
Elecrow Item #: EL-CCO10202C -

This is a 2 Pole 5.0mm Screw Terminal Block.It includes 5 units of Terminal Block.There are screws which is tightened for a secure connection for both lugs and bare wire. SpecificationRated: 250,16A(250V,17.5A)Contact resistance: 200mΩ MaxInsulation resistance: 5000MΩ MinTemp range: -30\u2103~+120\u2103Max Soldering: +260\u2103 5sWire range: 22-14AWG(1.5mm2)Strip length: 3.5mm ...

40 pin dual male splittable jumper wire - 300mm
Price: $7.47
View
Availability: Stocked
Elecrow Item #: EL-PCW40302P -

This is a splittable 40 pin 30mm length dual male jumper wire for 2.54mm, it is very flexible, can be used at bread board or other places that need connection. it is able to transform to 1-40 pin jumper wire.

U Shape Jumper Wires(140pcs pack)
Price: $11.67
View
Availability: Stocked
Elecrow Item #: EL-PCW14000A -

This box including over 10 different length(from 3mm-125mm) and various colors of jumper wire, perfectly fit breadboard and protoboard. 140pcs per box, you can use it over and over again!

10Pin Female Header - 2.00mm (5pcs Pack)
Price: $2.10
View
Availability: Stocked
Elecrow Item #: EL-CCO21002C -

This is a pack which includes 5pcs 10 pin female header. We use this header on all our XBee series modules. They have 0.2mm spacing between pins.SpecificationPin Pitch: 2.0mmContact Qty: 10Contact Type: Straight

8.3*5.5cm  Bread Board With Slot - Clear
Price: $7.47
View
Availability: Back Order
Elecrow Item #: EL-PBB18555C -

This is a half size breadboard with dimension 8.3*5.5 cm. It has two power rails on the sides to allow more than one power level. In addition, it can make the breadboard as thin as 3.5cm and stick it onto an Arduino protoshield by pull the power rails off easily. With a total of 400 tie in points, all pins are spaced by a standard 0.1"(2.54mm). It has a self-adhesive on the back and also interlocking parts, so you can hook as many together as you\'d like.Features400 Tie PointSelf adhesiveCan...

Header - 6-pin Female (PTH, 0.1")
OOD!
Price: $0.79
View
Availability: Back Order
Sparkfun Item #: PRT-11894 -

"These are standard 0.1" spaced header pins that can be through-hole mounted. This header connects perfectly with most 6-pin male headers. This is a 6-Pin female header. Documents: Datasheet "

Solderless Bread Board - 17.6*4.6cm
Price: $4.43
View
Availability: Stocked
Elecrow Item #: EL-PBB01655L -

This breadboard have 2x 60 rows of interconnected pins (5 per row) and two long rows on both sides - 700 pins in total. Its dimension is 17.6*4.6*8.3cm. Plesae note that it has no self-adhesive backing and no interlocking part.Features700 Tie PointDimensions: 17.6 * 4.6 * 8.3cm

RS232 Shifter Board Kit
Retail: $13.74
Price: $8.36
View
Availability: Stocked-NoBackOrder
Sparkfun Item #: PRT-00133 -

RS232 Shifter Board Kit Description: Get your PIC or other uC talking to your computer fast and easy with this board! This is a small custom PCB developed to connect the UART on a microcontroller directly to the computer without the hassle of a MAX232 circuit. Almost all current computers (less than 10 years old) utilize a serial port based on the EIA-232 standard which operates from +/-3-12V rather than the RS232 standard of +/-12V. This board takes signals from the computer/microcontroller...

SmartiPi Touch
Price: $41.23
View
Availability: Stocked
Sparkfun Item #: PRT-14059 -

"The SmartiPi Touch is a case and stand for the official Raspberry Pi 7" Touchscreen LCD. The display securely fits into the case with four screws, while a Raspberry Pi 2, 3, B+ or A+ is enclosed in the compartment on the back with a simple door. A ribbon cable that comes with the display connects into the Raspberry Pi DSI port. The stand has a pivot that allows you to adjust the angle of the screen for better viewing, as well as mounting points to affix it to a certain location. The SmartiPi...

16.5*5.5cm Bread Board With Slot - Clear
OOD!
Price: $10.50
View
Availability: Back Order
Elecrow Item #: EL-PBB16559P -

This is a full size breadboard with dimension 16.5*5.5 cm. It has two power rails on the sides to allow more than one power level.With a total of 830 tie in points, all pins are spaced by a standard 0.1"(2.54mm). It has a self-adhesive on the back and also interlocking parts, so you can hook as many together as you\'d like.Features830 Tie PointSelf adhesiveCan be interlocked2 power lanesDimensions: 16.5 * 5.5 cmPackage list16.5*5.5cm Bread Board With Slot – Clear x1Wiki & External links ...

40 Pin Break Away Male Header- Long Straight-10 Pcs
Price: $9.53
View
Availability: Out of Stock
DFRobot Item #: FIT0105 -

40 Pin Break Away Male Header- Long Straight-10 Pcs Introduction These are a longer version of our standard break away headers. They are 20mm long which allows you use them socket to socket. The plastic separator can be slid up or down to accommodate your needs. 40 pins that can be cut to any size. Used with custom PCBs or general custom headers. It is used on Arduino Ethernet Shield. Shipping List 40 Pin Header (10 units) ...

6xAA Battery Holder(double layer)
Price: $5.68
View
Availability: Out of Stock
DFRobot Item #: FIT0078 -

6xAA Battery Holder(double layer) This battery holder can hold 6 AA battery  which can make  7.2 V rechargeable battery pack from NiMH / NiCd cells or 9V battery pack from alkaline cells. It comes with a 6" Red & Black Wires with side by side & stack connection.    Specifications Cell Quantity: 6 Battery type: AA  Storage temperature: 25'C (77F, RoomTemperature) Max Operate temperature: 80'C (176F) ...

9V to Barrel Jack Adapter
Price: $2.99
View
Availability: Out of Stock
DFRobot Item #: FIT0131 -

Introduction This simple cable has so many uses! Plug a 9V battery into one end and connect the other end to anything with a 5.5x2.1mm, center-positive barrel jack. Use this cable to battery-power any device that needs 9V and has an on-board barrel jack - it works great for Arduinos, development boards, evaluation boards, and more! ...

Alligator Clip Test Cables (10 PCs Pack)
Price: $8.05
View
Availability: Out of Stock
DFRobot Item #: FIT0112 -

Introduction These are standard alligator to alligator (crocodile) clip test cables.   The alligator clip allow you attach the test point without hold the cables which is really handy.  The clip is strong and grippy.   Specification Contains two of each: Black, red, white, green, and yellow. 22 gauge heavy insulation copper wire alligator clips at both ends 30cm in length Shipping List 10 piece set, Color Coded may vary ...

Analog Voltage Divider
Price: $8.12
View
Availability: Out of Stock
DFRobot Item #: DFR0051 -

Analog Voltage Divider Introduction The Voltage Divider can detect the supply voltage upto 25V. The DFRobot Voltage Divider module is based on resistor divider principle. The voltage detection module allows the input voltage to reduce 5 times. As the Arduino analog input voltage is up to 5V, so voltage detection module's input voltage can not be greater than the 5Vx5 = 25V. Specification Type: Analog Input voltage (DC): Maximum 25V, Minimum 0.0245V Detects the supply voltage upto 25V 3...

Arduino Female Header-8 Pins- 10 Pcs
Price: $5.75
View
Availability: Out of Stock
DFRobot Item #: FIT0104 -

Arduino Female Header-8 Pins- 10 Pcs Introduction This is a 8-pin female header which is used on Arduino board.  Shipping List 8 Pin Header (10 units)

Breadboard Power Supply 5V/3.3V
Price: $5.75
View
Availability: Out of Stock
DFRobot Item #: DFR0140 -

This is a very simple board that takes a 6-12V input voltage and outputs a selectable 5V or 3.3V regulated voltage. All headers are 0.1" pitch for simple insertion into a breadboard. It can be either powered from 6-12 DC2.1 power jack or from USB power.  The maximum current it can provide is 500mA.  Specification Input voltage: 6-12V (Power Jack) 5V (USB) Output voltage:3.3V/5V Output current:500mA On/Off switch Power status LED Pin Head 5/3.3V output Central positive DC2.1 power...

Breakout Board for SC16IS750 I2C-SPI-to-UART IC
Price: $25.85
View
Availability: Stocked-NoBackOrder
Sparkfun Item #: BOB-09981 -

Breakout Board for SC16IS750 I2C/SPI-to-UART IC Description: This is a breakout board for the SC16IS750, a handy chip used to convert I2C or SPI serial signals to a single-channel, high-performance UART. As an application example: we use this chip on our WiFly Shield to allow an Arduino to communicate with the WiFly RN-131G module - which is normally controlled via a UART - using an SPI interface. This allows for greater communication speeds and frees up the Arduino's UART for...

Bus Pirate
Price: $51.79
View
Availability: Stocked-NoBackOrder
Sparkfun Item #: TOL-09544 -

Bus Pirate Description: The Bus Pirate, created by Ian Lesnet and featured on Hack a Day, is a troubleshooting tool that communicates between a PC and any embedded device over most standard serial protocols, which include I2C, SPI, and asynchronous serial - all at voltages from 0-5.5VDC. This product eliminates a ton of early prototyping effort when working with new or unknown chips. Working with the Bus Pirate is simple and effective - type commands into a terminal on your computer, those...

Cable for Shiftout
Price: $3.68
View
Availability: Out of Stock
DFRobot Item #: FIT0077 -

Introduction This cable is especially designed for Interface shield,shift out module, SPI Led and SPI LCD module.  It is has a female 2×3 IDC connector on each end that is designed to plug into a 0.100" (2.54 mm) 2×3 shrouded box header. Specification Length:20cm Female/Femal, IDC 2x3 Connector ...

Enclosure - Aluminum (112x61x31mm)
OOD!
Price: $6.28
View
Availability: Back Order
Sparkfun Item #: PRT-13839 -

"These are our small, beefy aluminum enclosures, which have been built tough enough to withstand a truck. This 2mm-thick, die-cast enclosure is rated IP54 against dust and splashing water. Because it’s aluminum, it’s easy to cut and drill so that you can add LCD screens, buttons and cable connections. If you want to “pretty up” your project, hit this with some fine-grit sand paper and buff it or just spray paint it! These enclosures are perfect for producing...

Enclosure - Aluminum (120x94.5x34mm)
OOD!
Price: $7.87
View
Availability: Back Order
Sparkfun Item #: PRT-13838 -

"These are our large, beefy aluminum enclosures, which have been built tough enough to withstand a truck. This 2mm-thick, die-cast enclosure is rated IP54 against dust and splashing water. Because it’s aluminum, it’s easy to cut and drill so that you can add LCD screens, buttons and cable connections. If you want to “pretty up” your project, hit this with some fine-grit sand paper and buff it or just spray paint it! These enclosures are perfect for producing...

Header - 10-pin Female (PTH, 0.1")
OOD!
Price: $0.79
View
Availability: Back Order
Sparkfun Item #: PRT-11896 -

"These are standard 0.1" spaced header pins that can be through-hole mounted. This header connects perfectly with most 10-pin male headers. This is a 10-Pin female header. Documents: Datasheet "

Header - 8-pin Female (PTH, 0.1")
OOD!
Price: $0.79
View
Availability: Back Order
Sparkfun Item #: PRT-11895 -

"These are standard 0.1" spaced header pins that can be through-hole mounted. This header connects perfectly with most 8-pin male headers. This is a 8-Pin female header. Documents: Datasheet "

Jumper Wires (F/M)
Price: $8.97
View
Availability: Out of Stock
DFRobot Item #: FIT0121 -

Introduction Breadboard jumper wire 65 pcs pack. Including 4 different length:200mm,165mm,125mm and 80mm.Perfect design for breadboard. Comes with F/M connectors. Specification 240mm x5  200mm x5 150mm x8 110mm x47   ...

Medium Bread Board Self Adhsive
Price: $12.65
View
Availability: Out of Stock
DFRobot Item #: FIT0009 -

Introduction This is a medium size breadboard with 600 tie points.  It has strong, self-adhesive backing.  It is ideal for high frequency and low noise circuits.  Specification Size:170*65mm  Suitable for 0.3-0.8 mm wire ...

Mesh cable guide (1.25m)
Price: $1.15
View
Availability: Out of Stock
DFRobot Item #: FIT0250 -

Mesh cable guide (1.25m) Introduction This is a black  braided cable guide. The braid provides some rigidity to the cables, also, it can be expanded by compressing it which will allow many more cables to fit inside.     Specification  Color: Black Length: 1.25m Inner diameter: 12mm   Shipping List Braided cable guide (1.25 meter) ...

Mini Bread Board 4.5x3.5cm - Black
OOD!
Price: $2.33
View
Availability: Back Order
Elecrow Item #: EL-PBB05545B -

The dimension of this mini breadboards is 45cm * 35mm * 9 mm\xe9\u201d\u203a\u013a\u017d\xa8t have a self-adhesive backing and 2 x 17 rows of interconnected pins (5 per row) \xe9\u02c6\u013d?170 pins in total. Besides, it is able to combine several mini boards with slot. This board is very suit for those project that need compact dimension.Features170 Tie PointSelf adhesiveCan be interlockedDimensions: 45 * 35 mm ...

Mini Bread Board 4.5x3.5cm - Blue
OOD!
Price: $2.33
View
Availability: Back Order
Elecrow Item #: EL-PBB15545B -

The dimension of this mini breadboards is 45cm * 35mm * 9 mm, it has a self-adhesive backing and 2 x 17 rows of interconnected pins (5 per row) , 170 pins in total. Besides, Users can also combine several this kind of mini boards with the slot. This board is very suit for those projects that need compact dimensionFeatures170 Tie PointSelf adhesiveCan be interlockedDimensions: 45 * 35 mm ...

Mini Bread Board 4.5x3.5cm - Green
OOD!
Price: $2.33
View
Availability: Back Order
Elecrow Item #: EL-PBB05545G -

The dimension of this mini breadboards is 45 × 35 ×9 mm\u010f\u017a\u0152it have a self-adhesive backing and 2 x 17 rows of interconnected pins (5 per row) - 170 pins in total. Besides, it is able to combine several mini boards with slot. This board is very suit for those project that need compact dimension.Features170 Tie PointSelf adhesiveCan be interlockedDimensions: 45 * 35 mm ...

Mini Bread Board 4.5x3.5cm - Red
OOD!
Price: $2.33
View
Availability: Back Order
Elecrow Item #: EL-PBB05545R -

The dimension of this mini breadboards is 45 × 35 ×9 mm\u010f\u017a\u0152it have a self-adhesive backing and 2 x 17 rows of interconnected pins (5 per row) - 170 pins in total. Besides, it is able to combine several mini boards with slot. This board is very suit for those project that need compact dimension.Features170 Tie PointSelf adhesiveCan be interlockedDimensions: 45 * 35 mm ...

Mini Bread Board 4.5x3.5cm - White
OOD!
Price: $2.33
View
Availability: Back Order
Elecrow Item #: EL-PBB05545W -

The dimension of this mini breadboards is 45 × 35 ×9 mm\u010f\u017a\u0152it have a self-adhesive backing and 2 x 17 rows of interconnected pins (5 per row) - 170 pins in total. Besides, it is able to combine several mini boards with slot. This board is very suit for those project that need compact dimension.Features170 Tie PointSelf adhesiveCan be interlockedDimensions: 45 * 35 mm ...

Mini Bread Board 4.5x3.5cm - Yellow
OOD!
Price: $2.33
View
Availability: Back Order
Elecrow Item #: EL-PBB05545Y -

The dimension of this mini breadboards is 45 × 35 ×9 mm\u010f\u017a\u0152it have a self-adhesive backing and 2 x 17 rows of interconnected pins (5 per row) - 170 pins in total. Besides, it is able to combine several mini boards with slot. This board is very suit for those project that need compact dimension.Features170 Tie PointSelf adhesiveCan be interlockedDimensions: 45 * 35 mm ...

Mini Bread Board Self Adhesive - Black
Price: $5.18
View
Availability: Out of Stock
DFRobot Item #: FIT0008-BK -

Mini Bread Board Self Adhesive - Black Introduction This is a very small breadboard with 170 tie points. This bread board is compatible with the Arduino Proto Shield. Strong self-adhesive backing. Measures 1.8"x1.4".You also have choices of different colors.     Specification 170 tie point breadboard 17 x 5 x 2 points Adhesive backing Black   Shipping List Black 170 tie point bread board (1 unit) ...

MiniMoto - DRV8830 Breakout
Price: $17.20
View
Availability: Stocked-NoBackOrder
Sparkfun Item #: BOB-11890 -

MiniMoto - DRV8830 Breakout Description: The MiniMoto is a great little breakout for the DRV8830 I2C DC motor driver. The MiniMoto is great for driving most small robotics. With an operating voltage range of 2.7V to 6.8V and a current limit of 1A the DRV8830 is a versatile little driver.  In addition to the benefit of being controlled via I2C, which frees up data lines and processing on the CPU to be used for other tasks, the MiniMoto has the lowest voltage output capability...

Pi Tin for the Raspberry Pi - Black
Price: $12.49
View
Availability: Stocked-NoBackOrder
Sparkfun Item #: PRT-11980 -

Pi Tin for the Raspberry Pi - Black Description: The Raspberry Pi is everybody's favorite little computer, the last thing that you'd want is for something bad to happen to it. Why not protect it with one of these snazzy plastic enclosures? These cases protect the Raspberry Pi from things like rogue wires that might short it out while still allowing full access to the board! Simply snap the RPi into the bottom half of the enclosure, then snap the two sides together. As you may have noticed,...

Pi Tin for the Raspberry Pi - Blue
Price: $12.49
View
Availability: Stocked-NoBackOrder
Sparkfun Item #: PRT-11981 -

Pi Tin for the Raspberry Pi - Blue Description: The Raspberry Pi is everybody's favorite little computer, the last thing that you'd want is for something bad to happen to it. Why not protect it with one of these snazzy plastic enclosures? These cases protect the Raspberry Pi from things like rogue wires that might short it out while still allowing full access to the board! Simply snap the RPi into the bottom half of the enclosure, then snap the two sides together. As you may have noticed,...