3D Printing

    Many of you don't like the nozzle clogs and blocks when you are a 3D printer owner. Every extruder nozzle must be cleaned out from time to time. These nozzles are very difficult to clean properly. Never mind. We have an effective weapon to deal with it�a drill cleaner. These Micro-drill bit Extruder Nozzle Cleaners are an essential item for you. The drills are hard and thin enough to get into the nozzle and extract the blocked filament. There are 5 types of drills of 0.2mm 0.3mm,...

    The RAMPS (RepRap Arduino Mega Pololu Shield) is an all-in-one design to fit the necessary components for a 3D printer into one plug in shield for an Arduino MEGA. The plug in shield design includes plug in stepper drivers and extruder control electronics sockets for easy service, part replacement, upgrade-ability and expansion. Additionally, a number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack....

Cleaning Filament is valuable when transitioning between filaments that require different printing temperatures or have very different colours. Cleaning Filament cannot be used to create objects, instead it is a complementary filament to properly maintain your 3D printer.You can use Cleaning Filament to purge the tool head of your 3D printer when going from a high temperature filament to a lower temperature filament, or when transitioning from a dark colour filament to a light colour filament....

This stepping motor was two phase mixing type.1m wire, one connect electrical machine, on the other end has variety optional ports; heat shrink tubing effect to prevent the wire tangled up.D-shaped axle with 22mm, electrical machine with high-torque, high-speed, low noise.      Features Drive mode: Chopping wave constant current drive Exciting mode: Two-phase 4-wire. It is available for rotation of forward and reverse Swerve: The order of power is AB-BC-CD-DA, from shaft...

This is an 20 tooth timing pulley with a center diameter of 5mm (0.2"), this is a good fit for mounting on common stepper motors. These pullies are great for many mechanical projects. They are also commonly used in 3D printers. |Specification| Teeth: 20 Inner diameter: 5mm(0.2") Teeth diameter: 12.5mm (0.49") Teeth Width: 6.8mm (0.27") Outer diameter: 15 mm (0.59") Fastening screws: M3 x2|ShippingList| 5mm Aluminum Timing Pulley For 3D Printer x2 M4 embedded screw x4? ...

This is an 20 tooth timing pulley with a center diameter of 8mm (0.31"). These pullies are great for many mechanical projects. They are also very commonly used in 3D printers. |Specification| Tooth: 20 inner diameter: 8mm (0.31") Teeth diameter: 12.5mm (0.49") Teeth Width: 6.8mm (0.27") Outer diameter: 15 mm (0.59") Fastening screws: M3 x2 |ShippingList| 20 Tooth MXL 8mm x2 M4 embedded screw x4 ...

    A4988 is a complete microstepping motor driver with built-in translator for easy operation. The product can be full, half, 1/4, 1/8 and 1/16 step mode to operate bipolar stepper motor output drive capacity of up to 35 V and � 2 A. A4988 includes a fixed off-time current regulator, the regulator can slow or mixed decay mode. The converter is the key to the easy implementation of the A4988. In inputting one pulse on the STEP input drives the motor one microstep. No phase...

"This is a 1kg (2.2lb) reel of 3mm black ABS (acrylonitrile butadiene styrene) plastic filament for 3D printing. ABS is a great general purpose filament with high strength and good print quality. ABS is one of the most popular 3D printing materials available due to its strength and ease of printing. This filament is an incredibly durable plastic that can be used in prototypes or even the parts found on your TAZ 3D printer! ABS prints can be sanded or smoothed using an advanced technique with...

"This is a 0.45kg (1lb) reel of 2.85mm “natural-colored” Alloy 910 nylon co-polymer filament for 3D printing. Specially developed to exhibit the ideal characteristics of several different classes of 3D printing filaments, Alloy 910 offers the strength and durability of nylon with the same minimal shrink nature of PLA. Alloy 910 makes for ideal material to be used in frames or enclosures that are subject to stress and high impact, and items exposed to repeated flexing such as...

    This Masking Tapes was make in China,which can take the place of the 3M2060.It is mainly used for hot bet in the 3D printer. Features Type:48MM X30M Thickness: 0.13mm Color:Blue long-term temperature resistance:130 degree Short-term temperature resistance:180 degree ...

"Heat set brass inserts allow a user to add mounting holes and hardware to any 3D printed or soft plastic enclosure. Use the heat set tips with your soldering iron to heat the brass inserts and then gently push them into place. Heat set inserts are brass nuts that are specially designed to be heated up and pressed into an undersized hole. The outside of the insert has spikes and fins that help the plastic flow around and form a tight bond with the surrounding material. While standard hex nuts...

This M6 nozzles is spare accessory for makerbot MK8 extruder.FeaturesMaterial:Brass Screw thread:M6Nozzle Precision: 0.2/0.4mm(optional)Suitable for 1.75mm filament

"This is a 0.45kg (1lb) reel of 3mm “clear” Bridge nylon co-polymer filament for 3D printing. Taulman’s “Bridge” high-strength nylon co-polymer bridges the strength of nylon 645 and the ease of printing of ABS/PLA. Items printed in Bridge nylon filament are stronger and more resilient than parts printed in more common materials. Since Bridge prints cleanly and easily, you can print complex models that are ready to be used. The combination of strength, reduced...

This is Aluminum Heater Block M6 Specialized for MK7 MK8 Makerbot 3D Printer Extruder.Features Material: aluminum Material of Print: 1.75mm PLA/ABS Thermistor: 100K NTC Operating voltage of cooling fan: 12V Heating rods: 6mm, 12V,40W

This box of grease is very small, light and easy to carry. It can be uesd in many places. It is suitable for the condition of light load or high speed plastic gear, plastic parts, nylon retainer bearing lubrication, protection and noise reduction. You will need it for your robot and 3D Printer. |Specification| Net Weight : 5g|ShippingList| Grease(5g) x1

Our GT2 pulley and belt combination provide you with much more precision and anti-backlash properties than other non round tooth profile timing pulleys. The GT2 pulley we machine can be used with 6mm width GT2 belt. It\'s a good choice for all kinds of machines. 3D printing is just one of these applications. These pulleys will fit 5mm smooth rod and 5mm motor shafts like those found on our NEMA17 Motors.FeaturesLonger Belt LifePrecision Registration Increased Load-carrying CapacityQuieter...

"3D Printing and Laser Cutting are awesome processes for making fast prototypes of complex parts but attaching those parts together can prove difficult. Glue works fine most of the time but only if you want a permanent bond. You can tap plastic parts and use bolts but the threads will be soft and probably won’t survive multiple assemblies. That’s where threaded inserts come in! Heat set inserts are metal (usually brass) nuts that are specially designed to be heated up and pressed...

    This is MK8 hot end,when the MK8 extruder plug can be used to replace. Features Material: Metal Extrusion nozzle: 0.4mm Material of Print: 1.75mm PLA/ABS Voltage of heating nozzle: 12V Thermistor: 100K NTC Heating rods: 6mm, 12V,40W ...

"This is a 1kg (2.2lb) reel of 3mm black INOVA-1800 co-polyester filament for 3D printing made from Eastman Amphora™ 1800 3D polymer. INOVA-1800 prints have a glossy, smooth finish and feature a great balance of strength and 3D printing ease. 3D prints with this filament are dimensionally stable, bridge well and are a great choice for interlocking objects, props and other functional 3D prints. This is the Cadillac of 3D printer filament and should be your go-to option for creating your...

This kit includes JST XHP-2, XHP-3 and XHP-4 housing (20 units each), through-hole type shrouded header (20 units each) and crimp contact (100 units). |Specification| Current rating:3A AC,DC (AWG #22) Voltage rating:250V AC,DC Temperature range?-25? to +85??including temperature rise in applying electrical current? Contact resistance?Initial value/10m &;Omega; max. After environmental testing/20m &;Omega; max. Insulation resistance?1000M &;Omega; min. Withstanding voltage?1000V AC/minute...

This is a Dual Extruder which is used on Makerbot 3D printers. The two print heads are conjoined with a piece of high hardness aluminum bar with good heat dispersion and high reliability. The main benefits of this Dual Extruder includes being able to print more complex objects with support structures and more aesthetically pleasing objects that feature multiple colors or multiple materials.Features Material: Metal Extrusion nozzle: 0.2mm,0.4mm (optional) Material of Print: 1.75mm PLA/ABS Flow...

     Stepper motors are different from DC motors in that they have to be pulsed to move in set increments. That means you can't simply hook them up to a power supply to make them go, but they have other advantages, like accurate positioning (1 pulse=1 increment of movement), and lots of low-speed torque (ability to twist things).      This 4-wire bipolar stepper has 1.8� per step for smooth motion and a nice holding torque. This NEMA-17 stepper motor...

    Stepper motors are different from DC motors in that they have to be pulsed to move in set increments. That means you can't simply hook them up to a power supply to make them go, but they have other advantages, like accurate positioning (1 pulse=1 increment of movement), and lots of low-speed torque (ability to twist things). This 4-wire bipolar stepper has 1.8� per step for smooth motion and a nice holding torque. This NEMA-17 stepper motor produces a whopping 4800g*cm...

    Some endstops are needed in a 3D printer , this opto Endstop for CNC 3D Printer RepRap Makerbot Prusa Mendel RAMPS is very accurate and reliable . When the light inside the sensor is blocked, Opto Endstop will immediately output the digital signal, and the LED will be on thus to remind you the working state of this sensor.     For the installation, Makers made some useful suggestions such as here.      Specification Operating...

This is a spare push in to connect fitting for All Metal J-head bowden extruder,but also designed for 1.Polyurethane or Nylon tubing 2.Quick and Reliable connections 3.Reusable: Multiple connections/disconnections 4.Convenient elliptical sleeve configuration 5.Metallic body made of non-corrosive, non-contaminant Nickel-plated Brass 6.Outside (and Inside where applicable) hexagonal wrench tighteningFeatures Material:Brass Model:Pneumatic Push to Connect fitting Straight Male SPC 6-01 Inner...

This is 3d printer accessories 6 mm package line pipe winding line management set line protective sleeve pipe winding wire.Features 100% Brand new and high quality Type : Winding pipe Size : 6mm Package content : 1pcs 1 meter 6mm winding pipe

This PTFE Tubing outer diameter is 6mm and the inner diameter is 4mm,which is suitable for the 3mm filament.It is mainly used for 3D printer install the inner tune.It can held the filament smooth siding and prevent the filament melting in advance.FeaturesLength:1 meterOuter diameter: 6mmInner diameter: 4mmSuitable for the 3mm filamentMaterial\u010f\u017a\u0161teflon Color:white ...

    This is 12V 40W Ceramic Cartridge Heater. Features Voltage:12V Power: 40W Core: ceramic Diameter: 6mm Lenght: 20mm Lead Wire lenght: 1M

    Our GT2 pulley and belt combination provide you with much more precision and anti-backlash properties than other non round tooth profile timing pulleys. The GT2 pulley we machine can be used with 6mm width GT2 belt. It's a good choice for all kinds of machines. 3D printing is just one of these applications. These pulleys will fit 5mm smooth rod and 5mm motor shafts like those found on our NEMA17 Motors. Features Tooth Profile: gt2 profile Teeth:20 Gear Width: for up to...

    This Extruder Hot End is spare for makerbot extruder or another 3D printer used for 1.75mm filament. Features Pipes Specifications: M6X26.5mm Material: Stainless steel (high-quality 304 stainless steel to prevent rusting) Thread:M6 Front-end thread length:5mm,the another length:18mm Length: 26.5mm ...

The heatbed improves print quality, especially when printing ABS by reducing thermal warping. The diameter of the total heatbed is 220mm, and the diameter of the active heated area is 200mm. It’s as the width as 2mm. The heatbed can take 12V input and the power is 120W. In this produce, we already welded 1 meter high temperature wire, and provide a thermistor.FeaturesDouble layer PCBThickness: 2mmTotal heatbed diameter: 220mm Active heated area diameter: 200mm Power input: 12V Red...

This M6 nozzles is spare accessorie for J-head/E/3D extruder. Suitable for 1.75mm filament .FeaturesSize:12.5mm * 8mm Material: Brass Thread:M6Nozzle Accuracy: 0.2/0.4mmSuitable for 1.75mm filament

"The LulzBot® TAZ 6 is the most reliable, easiest-to-use desktop 3D printer ever, featuring innovative self-leveling and self-cleaning, and a modular tool head design for flexible and multimaterial upgrades. This 3D printer is able to facilitate more consistent, higher-quality prints than ever. The TAZ 6 features tetherless printing through an SD card with a versatile, multifunctional graphic LCD controller and an internal power supply. It boasts a spacious 11.02 in x 11.02 in x 9.8 in...

     The polyimide tape is an insulator resistant to high temperatures.It is an essential accessory for assembly and use of your 3D printer.Tape with polyimide film as the backing material coated high temperature resistant silicone, color is dark brown (amber), tape good stickiness, good docile, high temperature resistance, solvent resistance, permeability of tin, glue, product has excellent electrical properties. Features Long:30m Width:4mm Short-term heat resistance of...