Sensors

The MQ-137 is an Ammonia (NH₃) gas sensor from Winsen. The sensing element is SnO2, which has lower conductivity in clean air. When NH₃ (Ammonia) gas exists, the sensor’s conductivity gets higher...

The MQ-137 is an Ammonia (NH₃) gas sensor from Winsen. The sensing element is SnO2, which has lower conductivity in clean air. When NH₃ (Ammonia) gas exists, the sensor’s conductivity gets higher along with the gas concentration rising. A simple circuit makes measuring this change in conductivity and turning it into data fairly straight-forward, but does require some calibration. For easy Solderability; use our Gas Sensor Breakout Board. Documents: Datasheet Videos ...

Analog Gas Sensor Introduction The gas sensor detects smoke, methane, carbon dioxide and other gases. It is able to give alarms when the smoke/gas leaks.  You can adjust the sensitivity with...

Analog Gas Sensor Introduction The gas sensor detects smoke, methane, carbon dioxide and other gases. It is able to give alarms when the smoke/gas leaks.  You can adjust the sensitivity with the potentiometer. Specification Type: Analog Detector: QM-NG1 Power supply needs: 5V Current: 100mA Pin Definition:  1-Output  2-GND  3-PWR  Document Datasheet Manual Shipping List Sensor (1 unit) Analog Sensor Cable (1 unit) (SKU:FIT0031) ...

Have you ever reached into a drawer of antennas and wondered what the frequency was for each of them? Now with this antenna frequency sticker sheet you can label your antennas. Each sheet comes with...

Have you ever reached into a drawer of antennas and wondered what the frequency was for each of them? Now with this antenna frequency sticker sheet you can label your antennas. Each sheet comes with 75 stickers of commonly used frequencies. Each individual sticker is: W 15.328mm x H 8.978mm Includes: 75 Stickers: 10x 915MHz 10x 2.4GHz 5x 868MHz 5x 4G 5x 5G 5x 433MHz 5x 5.8GHz 5x L1 5x L2 5x WiFi 5x Bluetooth 5x BLE 5x LoRa ...

A first for the Raspberry Pi ecosystem: A 64MP camera module that matches the specs of smartphone cameras. The Arducam 64MP Camera Module puts a 64MP sensor with autofocus in the standard Raspberry...

A first for the Raspberry Pi ecosystem: A 64MP camera module that matches the specs of smartphone cameras. The Arducam 64MP Camera Module puts a 64MP sensor with autofocus in the standard Raspberry Pi camera module form factor. Much like the other cameras we carry from Arducam, this sensor easily interfaces to the Raspberry Pi line via the MIPI CSI-2 Ribbon Cable and connectors found on most of the Pi boards. The ArduCam 64MP Autofocus Camera Module allows you to take still images at the...

Based on the 16MP Sony IMX519 sensor, this new camera module gives all Raspberry Pi users every bit of power they need to build future-proof projects. Though the camera boasts two times the...

Based on the 16MP Sony IMX519 sensor, this new camera module gives all Raspberry Pi users every bit of power they need to build future-proof projects. Though the camera boasts two times the resolution of the V2 (16MP with the V3), the exciting new feature is autofocus! The camera makes for a great, low cost alternative to the other Raspberry Pi camera options out there, yet doesn't sacrifice performance. Note: This version does not include the ABS Enclosure which can be purchased directly from...

Bare Conductive's Electric Paint is just like any other water-based paint... except that it's electrically conductive! This means that you can actually paint wires onto things like models, clothes,...

Bare Conductive's Electric Paint is just like any other water-based paint... except that it's electrically conductive! This means that you can actually paint wires onto things like models, clothes, furniture, walls, almost anything you can think of. Standard acrylic or water-based paints can even be used alongside Electric Paint to act as insulation or to create multi-layer circuitry! Oh yeah, and now? It comes in a sachet! Bare's Electric Paint Sachets are a great electronics prototyping tool...

The MPL115A1 is a digital barometer that uses MEMs technology to give accurate pressure measurements between 50kPa and 115kPa. We stock the SPI interface version of the sensor. Average current...

The MPL115A1 is a digital barometer that uses MEMs technology to give accurate pressure measurements between 50kPa and 115kPa. We stock the SPI interface version of the sensor. Average current consumption is 10µA at one measurement per second. The sensor outputs both temperature and pressure readings on the SPI bus. See page 3 of the datasheet for information on how to take readings from the pressure sensor. Breakout board coming soon! Features: Wide supply voltage range -40°C to 105°C maximum...

This is a cost-effective and highly functional hall-effect sensor. The Melexis 90217 is designed to be used with a bias magnet south facing the back (non-marked) side of the IC. With a single Hall...

This is a cost-effective and highly functional hall-effect sensor. The Melexis 90217 is designed to be used with a bias magnet south facing the back (non-marked) side of the IC. With a single Hall plate, this sensor is immune to common rotary alignment problems. Very easy to interface with all microcontrollers. Features: Short circuit protection Rotary position gear tooth sensing ability No rotary orientation concerns High speed operation No chopper delay Zero speed detection On-chip 10 bit...

Bone conduction is a way of sound transmission. The sound is converted into different frequencies of mechanical vibration, and transmitted through human skull, bone labyrinth, inner ear lymphatic...

Bone conduction is a way of sound transmission. The sound is converted into different frequencies of mechanical vibration, and transmitted through human skull, bone labyrinth, inner ear lymphatic transmission, helix, auditory nerve, auditory center.Bone conduction headphonesThis kit is composed by a bone conduction speaker, a speaker driver board and other kinds of accessories. This kit is intended to help understand the principles of bone conduction technology, making hearing aids or bone...

This cable is especially designed for Interface shield,shift out module, SPI Led and SPI LCD module. It is has a female 2&;times;3 IDC connector on each end that is designed to plug into a 0.100"...

This cable is especially designed for Interface shield,shift out module, SPI Led and SPI LCD module. It is has a female 2&;times;3 IDC connector on each end that is designed to plug into a 0.100" (2.54 mm) 2&;times;3 shrouded box header. |Specification| Length:20cm (7.9&;#39;&;#39;) Female/Femal, IDC 2x3 Connector|ShippingList| Cable for Shiftout x1

Now, it is time to add a more fancy interactive way to your project. This DFRobot touch kit comes with three types touch sensors. An ipod styple wheel touch, a keypad touch which supports backlit...

Now, it is time to add a more fancy interactive way to your project. This DFRobot touch kit comes with three types touch sensors. An ipod styple wheel touch, a keypad touch which supports backlit and a grid touch pad which can recoginze something unique. This kit utilizes the not very "latest" capactive touch technology which make the sensing very sensitive. The kit is designed to be compatible with Arduino. Get Started with Capacitive Touch Kit Tutorial|Specification| Operation Voltage:5V...

The SCD30 from Sensirion is a high quality Nondispersive Infrared (NDIR) based CO₂ sensor capable of detecting 400 to 10000ppm with an accuracy of ±(30ppm+3%). In order to improve accuracy the SCD30...

The SCD30 from Sensirion is a high quality Nondispersive Infrared (NDIR) based CO₂ sensor capable of detecting 400 to 10000ppm with an accuracy of ±(30ppm+3%). In order to improve accuracy the SCD30 has temperature and humidity sensing built-in, as well as commands to set the current altitude. For additional accuracy the SCD30 also accepts ambient pressure readings! We've written an Arduino library to make reading the CO₂, humidity, and temperature very easy. It can be downloaded through the...

The Day of the Dead only comes around once a year but what if you could celebrate it any day you want? With this black version of the Day of the Geek soldering kit you will be able to learn the...

The Day of the Dead only comes around once a year but what if you could celebrate it any day you want? With this black version of the Day of the Geek soldering kit you will be able to learn the basics of soldering by being able to assemble a light-up skull badge! Each Day of the Geek kit takes about 5-10min to assemble with basic soldering materials (not included). Say no to sugar skulls and say yes to solder skulls instead! Every Day of the Geek Soldering Badge Kit includes one black skull...

The Day of the Dead only comes around once a year but what if you could celebrate it any day you want? With this white version of the Day of the Geek soldering kit you will be able to learn the...

The Day of the Dead only comes around once a year but what if you could celebrate it any day you want? With this white version of the Day of the Geek soldering kit you will be able to learn the basics of soldering by being able to assemble a light-up skull badge! Each Day of the Geek kit takes about 5-10min to assemble with basic soldering materials (not included). Say no to sugar skulls and say yes to solder skulls instead! Every Day of the Geek Soldering Badge Kit includes one black skull...

DHT11 Temperature and Humidity Sensor This DHT11 Temperature and Humidity Sensor features a calibrated digital signal output with the temperature and humidity sensor complex. Its technology ensures...

DHT11 Temperature and Humidity Sensor This DHT11 Temperature and Humidity Sensor features a calibrated digital signal output with the temperature and humidity sensor complex. Its technology ensures the high reliability and excellent long-term stability. A high-performance 8-bit microcontroller is connected. This sensor includes a resistive element and a sense of wet NTC temperature measuring devices. It has excellent quality, fast response, anti-interference ability and high cost performance...

This is an anti-rust, robust and precise SHT10 sensor, which can master enterprise-class and industrial-level applications. It can be applied in various fields: telepoint base stations, electronic...

This is an anti-rust, robust and precise SHT10 sensor, which can master enterprise-class and industrial-level applications. It can be applied in various fields: telepoint base stations, electronic control cabinet, production site, storehouse, machine rooms, greenhouses, animal farming, medicine stock and etc. Metallic package enables it to deal with the very dusty or other severe circumstance. the wall-hanging style makes it easy to install. The metallic mesh covering the sensor adopts method...

The MQ-9B is a CO and CH₄ gas detection sensor form Winsen. The sensing material of the MQ-9B is SnO2, which has a low conductivity in clean air. It detects carbon monoxide (1.5V) by method of...

The MQ-9B is a CO and CH₄ gas detection sensor form Winsen. The sensing material of the MQ-9B is SnO2, which has a low conductivity in clean air. It detects carbon monoxide (1.5V) by method of cycling high and low temperature. The sensor’s conductivity gets higher with the CO and CH₄ gas concentration rising. The sensing range is 10-500ppm CH₄. A simple circuit makes measuring this change in conductivity and turning it into data fairly straight-forward, but does require some calibration. For...

Sharp GP2Y1010AU Dust Sensor requires some wiring on the breadboard and a list of components to make it Arduino compatible. This has turned down several people due to the thin wires of the sharp...

Sharp GP2Y1010AU Dust Sensor requires some wiring on the breadboard and a list of components to make it Arduino compatible. This has turned down several people due to the thin wires of the sharp sensor making it yet another addition to the drawer. We've listened your requests and created this adapter so you can get started right away on your project. If you are planning to assemble several sensors for your air station and need to have it working soon, this adapter will save time on circuit...

The 6-Channel Temperature Monitor can measure temperatures from as low as −240°C up to +850°C (real-world limits greatly depend on the sensors being used). Up to six 3-wire PT100 sensors (not...

The 6-Channel Temperature Monitor can measure temperatures from as low as −240°C up to +850°C (real-world limits greatly depend on the sensors being used). Up to six 3-wire PT100 sensors (not included) can be connected for measuring up to six temperatures. Measured temperature values are sent on a serial port for data logging and/or further processing. The kit includes an optional serial LCD for displaying readouts right on the board. Note: The kit requires soldering, a Serial to USB...

The EX8036 Stereo Camera from eYs3D is a high-end imager controller and patterned IR illuminator with a global shutter capable of both color and depth-map video modes. Thanks to its dual cameras,...

The EX8036 Stereo Camera from eYs3D is a high-end imager controller and patterned IR illuminator with a global shutter capable of both color and depth-map video modes. Thanks to its dual cameras, this Stereo Camera is ideally used in applications involving VR/AR, people and thing counting, and obstacle avoidance. The best part about this module is the fact that it has been designed to be as straight forward and easy to use as possible for a stereo camera. Simply plug in the included USB 3.0...

Fingerprint scanners are awesome! Why use a key when you have one right at the tip of your finger? Unfortunately, they're often unreliable or difficult to implement. Well not anymore! This great...

Fingerprint scanners are awesome! Why use a key when you have one right at the tip of your finger? Unfortunately, they're often unreliable or difficult to implement. Well not anymore! This great GT-521F52 fingerprint module from ADH-Tech communicates over TTL Serial so you can easily embed it into your next project. The module itself does all of the heavy lifting behind reading and identifying the fingerprints with an onboard optical sensor and 32-bit ARM Cortex M3 processor. To get started,...

The GT-NUCL1633K1 is the latest miniature fingerprint sensor with extensive enhancements on power consumption and user flexibility from ADH-Tech. It allows 360-degree rotation, which enables maximum...

The GT-NUCL1633K1 is the latest miniature fingerprint sensor with extensive enhancements on power consumption and user flexibility from ADH-Tech. It allows 360-degree rotation, which enables maximum performance without compromising on design aesthetics. It even works well in less than ideal conditions like when a finger is wet. The product integrates an optical sensor, light source, and touch under a glass cover. This allowing it to instantaneously capture high resolution images of the...

This is a piezoresistive force sensor from Tekscan. The harder you press, the lower the sensor's resistance. Pressing hard, the resistance changes from infinite to ~50k. The sensor itself is thin...

This is a piezoresistive force sensor from Tekscan. The harder you press, the lower the sensor's resistance. Pressing hard, the resistance changes from infinite to ~50k. The sensor itself is thin and flexible, but the resistance does not change while being flexed. Resistance changes only when pressure is applied to the round area at the end of the sensor. Used as a presence sensor (someone standing), weight sensor, pressure sensor (impact testing), etc. The overall length is about 2.25". The...

The FLIR Lepton® 2.5 - Thermal Imaging Module is a radiometric-capable long wave infrared (LWIR) camera solution that is smaller than a dime, fits inside a smartphone, and is less expensive than...

The FLIR Lepton® 2.5 - Thermal Imaging Module is a radiometric-capable long wave infrared (LWIR) camera solution that is smaller than a dime, fits inside a smartphone, and is less expensive than traditional IR cameras. With a focal plane array of 80x60 active pixels, this Lepton easily integrates into native mobile-devices and other electronics as an IR sensor or thermal image sensor. The radiometric Lepton captures accurate, calibrated, and non-contact temperature data in every pixel. For...

The FLIR Lepton® Thermal Camera Breakout Board is an easy-to-interface evaluation board to quickly connect the FLIR Lepton camera module to common platforms like Raspberry Pi or custom hardware. It...

The FLIR Lepton® Thermal Camera Breakout Board is an easy-to-interface evaluation board to quickly connect the FLIR Lepton camera module to common platforms like Raspberry Pi or custom hardware. It provides onboard power supplies, generated from 3 – 5.5V, and a master clock. Local power supplies, the master clock, and the power-up sequence components can all be bypassed using a jumper. This breakout works with all FLIR Lepton modules. Note: The FLIR Lepton Breakout Board V2 does not include a...

Do you see what we see? With the FLIR Radiometric Lepton® Dev Kit v2 you will be able to bring FLIR's thermal imaging reliability and power to your Arduino, Raspberry Pi, or any ARM based...

Do you see what we see? With the FLIR Radiometric Lepton® Dev Kit v2 you will be able to bring FLIR's thermal imaging reliability and power to your Arduino, Raspberry Pi, or any ARM based development tool all in an easy to access breadboard friendly package. This kit includes a breakout as well as the Lepton® 2.5 longwave infrared (LWIR) imager. All you need to do to get this kit set up, simply attach the Lepton® imager module into the provided breakout, connect the headers, and you will be...

Flymaple is a Quadcopter controller board, based on the Maple Project. The FlyMaple embeds a STM32F103RET6 (ARM Cortex-M3) as it's main MCU. It integrates a 3-Axis accelerometer,a 3-Axis gyroscope,a...

Flymaple is a Quadcopter controller board, based on the Maple Project. The FlyMaple embeds a STM32F103RET6 (ARM Cortex-M3) as it's main MCU. It integrates a 3-Axis accelerometer,a 3-Axis gyroscope,a 3-Axis compass and a barometric pressure sensor. By using the 10 dgrees of freedom IMUs and powerful 72MHz high-performation microcontroller, flymaple is powerful enough to handle a complex algorithm and manage a robot motion system at the same time. The design of flymaple is based on the maple,...

The LIDAR-Lite v4 Qwiic from GARMIN is a high-performance, wireless optical distance measurement sensor that doesn't require any soldering to get started. This is the ideal solution for drone,...

The LIDAR-Lite v4 Qwiic from GARMIN is a high-performance, wireless optical distance measurement sensor that doesn't require any soldering to get started. This is the ideal solution for drone, robot, IoT, or unmanned vehicle operations when space is tight and power is limited. This sensor has up to a 10 meter range, 1cm resolution, and requires 85mA during data acquisition. The user can read and write to the LIDAR-Lite v4 using the I2C protocol; this is where the addition of the SparkFun Qwiic...

The ZMOD4450 Gas Sensor Module is designed for detecting gases associated with food ripening or rotting, and is targeted for use in refrigeration air quality (RAQ) applications (e.g., food storage...

The ZMOD4450 Gas Sensor Module is designed for detecting gases associated with food ripening or rotting, and is targeted for use in refrigeration air quality (RAQ) applications (e.g., food storage and shipping, including humid and dusty applications with the possibility of water spray, condensation, or immersion). It is a 12-LGA assembly (3.0 × 3.0 × 0.7 mm) that consists of a gas sense element and a CMOS signal conditioning IC. The module’s sense element consists of heater element on a...

This Gravity Analog 20A current sensor is based on the Hall current sensing principle. It can be used for AC or DC current measurement, has a wide voltage range, a small footprint, requires no...

This Gravity Analog 20A current sensor is based on the Hall current sensing principle. It can be used for AC or DC current measurement, has a wide voltage range, a small footprint, requires no soldering and has a high level of precision.We have added high-voltage isolation in the circuit design for safety reasons and a non-conductive acrylic plate has been attached to the bottom of the PCB to prevent accidents such as short circuits, electric shocks and any other potential danger.This...

This is a breakout board for the fully integrated Hall Effect based linear ACS758 current sensor. The sensor gives precise current measurement for both AC and DC signals.The thickness of the copper...

This is a breakout board for the fully integrated Hall Effect based linear ACS758 current sensor. The sensor gives precise current measurement for both AC and DC signals.The thickness of the copper conductor allows survival of the device at high overcurrent conditions. The ACS758 outputs an analog voltage output signal that varies linearly with sensed current. This current sensor enables you to monitor currents in your project every second for energy saving or circuit protecting purposes. This...

nt to measure AC current it is impractical and hazardous to cut in to your live wiring. The analog AC current sensor developed by DFRobot is a good solution to this problem. Using induction you can...

nt to measure AC current it is impractical and hazardous to cut in to your live wiring. The analog AC current sensor developed by DFRobot is a good solution to this problem. Using induction you can measure AC current without intrusive methods. Place your AC wire inside the unit, connect the unit to the sensor board using the 3.5mm jack connector and connect the sensor board to an analog input on your microcontroller. Use this sensor to measure AC motors, lighting equipment, air compressors or...

This Arduino flame sensor can be used to detect fire or other wavelength at 760 nm ~ 1100 nm light. In the fire-fighting robot game, the flame plays an important role in the probe, which can be used...

This Arduino flame sensor can be used to detect fire or other wavelength at 760 nm ~ 1100 nm light. In the fire-fighting robot game, the flame plays an important role in the probe, which can be used as the robot's eyes to find fire source or football. It can make use of fire-fighting robots, soccer robots. The Flame sensor has probe angle of 60 degrees, two M3 mounting holes is provided to install on various platforms. This arduino flame sensor's operating temperature is -25 degrees Celsius to...

what's the best way to detect the magnet? Use anther magnet. But it's not sensitive enough. You have to feel it by youself.Right. This magnetic sensor knows whether there is a magnetic object nearby...

what's the best way to detect the magnet? Use anther magnet. But it's not sensitive enough. You have to feel it by youself.Right. This magnetic sensor knows whether there is a magnetic object nearby or not. And it correctly tells you through ditigal output.See below picture for a quick demo! |Features| Wide voltage range from 3.3V to 5V Standard assembling structure (Times-of-5mm Center distance between two 3mm mounting holes) Easily recognitive interfaces of sensors ("A" for analog and "D"...

What's the simplest way to check vibration with Arduino? Use a vibration sensor from DFRobot. You can directly plug it on our IO Expesion Shield V7. Just vibrate this sensor, Arduino can receive a...

What's the simplest way to check vibration with Arduino? Use a vibration sensor from DFRobot. You can directly plug it on our IO Expesion Shield V7. Just vibrate this sensor, Arduino can receive a digital signal. It's easy to acount and program in Arduino. Despite it's simple, you can make full use of it with creative thinking, like step counting, Crash warning light and so on. Inprovement Wide voltage range from 3.3V to 5V Standard assembling structure (Times-of-5mm Center distance between...

Lots of robot projects need joystick. This updated joystick module V2 provides an affordable solution. Simply connect to two analog inputs, the robot is at your commands with X,Y control. It also...

Lots of robot projects need joystick. This updated joystick module V2 provides an affordable solution. Simply connect to two analog inputs, the robot is at your commands with X,Y control. It also has a switch that is connected to a digital pin. This joystick module can be easily connect to Arduino by our IO Expansion Shield with supplied cables.Notice: The new version of analog sensor port pin mapping has been changed as the following two features.|features| Wide voltage range from 3.3V to 5V...

An infrared transmitter is simply a Light Emitting Diode which generates IR light (invisible IR light)--light with a wavelength of between 1 mm and 750 nanometers, and some associated circuitry. In...

An infrared transmitter is simply a Light Emitting Diode which generates IR light (invisible IR light)--light with a wavelength of between 1 mm and 750 nanometers, and some associated circuitry. In an infrared remote control, for example, pushing a button sends an electric signal to the LED, which converts the signal into a beam of infrared light. The receiving device detects the light with a photo diode and converts it to an electrical signal which, via an integrated circuit, controls its...

This is a line tracking (following) sensor to guide your robot by telling white from black quickly and accurately. It is commonly used in arduino robot project, and probably is the best line...

This is a line tracking (following) sensor to guide your robot by telling white from black quickly and accurately. It is commonly used in arduino robot project, and probably is the best line following sensor in the market.Line following is the most basic function of smart mobile robot. As you can see line tracking robot one of the easiest ways for a robot to successfully and accurately navigate. We designed this new generation of line tracking sensor to be your robot's powerful copilot all the...

HC-SR04 Ultrasonic Module Super easy, great price ultrasonic range detection for your project.  Ultrasonic ranging module HC - SR04 provides 2cm - 400cm non-contact measurement...

HC-SR04 Ultrasonic Module Super easy, great price ultrasonic range detection for your project.  Ultrasonic ranging module HC - SR04 provides 2cm - 400cm non-contact measurement function, the ranging accuracy can reach to 3mm. The modules includes ultrasonic transmitters, receiver and control circuit. Specifications: Working Voltage DC 5 V  Working Current 15mA  Max Range 4m  Min Range 2cm  MeasuringAngle 15 degree  Trigger Input Signal 10uS...

RCWL-0516 is a technology that uses radar Doppler, microwave induction special module for detecting moving objects. The RCWL-0516 microwave radar sensor module can detect inert objects at the...

RCWL-0516 is a technology that uses radar Doppler, microwave induction special module for detecting moving objects. The RCWL-0516 microwave radar sensor module can detect inert objects at the condition that it has enough density, volume and it is in motion. THis microwave radar sensor will sense motion through most anything. The more shielding there is, the less detection range you get. It can detect motion through glass, drywall walls, ceilings and floors. It is very sensitive. You might have...

Humidity and Temperature Sensor - SHT15 BreakoutThis is a simple breakout board for the SHT15 humidity sensor from Sensirion. The SHT15 digital humidity and temperature sensor is fully...

Humidity and Temperature Sensor - SHT15 BreakoutThis is a simple breakout board for the SHT15 humidity sensor from Sensirion. The SHT15 digital humidity and temperature sensor is fully calibrated and offers high precision and excellent long-term stability at low cost. The digital CMOSens Technology integrates two sensors and readout circuitry on one single chip. These sensors are really impressive! Very sensitive and straight forward to use. Board comes assembled and tested with the...

The MQ-136 is a Hydrogen Sulfide detection sensor with a sensing range of 1 - 200ppm. The sensing element is SnO2, which has lower conductivity in clean air. When H₂S gas exists, the sensor’s...

The MQ-136 is a Hydrogen Sulfide detection sensor with a sensing range of 1 - 200ppm. The sensing element is SnO2, which has lower conductivity in clean air. When H₂S gas exists, the sensor’s conductivity gets higher along with the gas concentration rising. A simple circuit makes measuring this change in conductivity and turning it into data fairly straight-forward, but does require some calibration. For easy Solderability; use our Gas Sensor Breakout Board. Documents: Datasheet Videos ...

Introductiona|This bracket is designed for Gravity: Arduino Adjustable Infrared Distance Sensor which can be used for the obstacle avoidance or objection detection. It provides a easy installation...

Introductiona|This bracket is designed for Gravity: Arduino Adjustable Infrared Distance Sensor which can be used for the obstacle avoidance or objection detection. It provides a easy installation of sensor on various robot platforms or other interactive media devices.?|Specification| Probe diameter: 18mm (0.7 in)|ShippingList| Bracket x1 Screw sets x3 ...

Infrared proximity sensor made by Sharp. Part # GP2Y0A41SK0F has an analog output that varies from 3.1V at 4cm to 0.3V at 30cm with a supply voltage between 4.5 and 5.5VDC. The sensor has a Japanese...

Infrared proximity sensor made by Sharp. Part # GP2Y0A41SK0F has an analog output that varies from 3.1V at 4cm to 0.3V at 30cm with a supply voltage between 4.5 and 5.5VDC. The sensor has a Japanese Solderless Terminal (JST) Connector. We recommend purchasing the related pigtail below or soldering wires directly to the back of the module. Documents: Datasheet ...

The TNm infrared thermometer module is is a long distance thermometer specially designed for a high sensitivity, high accuracy,low noise and low power consumption. MEMS thermopile detector and a...

The TNm infrared thermometer module is is a long distance thermometer specially designed for a high sensitivity, high accuracy,low noise and low power consumption. MEMS thermopile detector and a high accurate ambient temperature compensation technique are used for the TNm infrared thermometer module.|Specification| Operating Voltage: 3V or 5V Measurement Range: -33~220&;deg;C / -27~428&;deg;F Operating Range: -10~50&;deg;C / 14~122&;deg;F Accuracy Tobj=15~35&;deg;C, Tamb=25&;deg;C :...

The Kitronik Smart Air Quality Board for Pico provides a complete air monitoring and reporting solution for the Raspberry Pi Pico. The wealth of onboard sensors and connection points allow you to...

The Kitronik Smart Air Quality Board for Pico provides a complete air monitoring and reporting solution for the Raspberry Pi Pico. The wealth of onboard sensors and connection points allow you to log, store and display data effectively with the Pico filesystem and an OLED screen. There are also connection points for external devices, such as analogue sensors, servos, motors, and heater pads. The board includes a dual row of pin sockets to connect your Raspberry Pi Pico. The Pico can then read...

The KR Sense 45A is a small voltage and current sense breakout board. DC current is determined by measuring a voltage drop across a parallel shunt resistor, then converted to a final analog voltage...

The KR Sense 45A is a small voltage and current sense breakout board. DC current is determined by measuring a voltage drop across a parallel shunt resistor, then converted to a final analog voltage output by the INA-169. Voltage sense is accomplished by scaling to 3.3V ADC range by a precision resistor divider. This version of the sensor features a maximum voltage tolerance of 51.8V at 44.7A, to be exact. Please be aware that KR Sense boards are supplied without leads or connectors. The pad...

The KR Sense 90A is a small voltage and current sense breakout board. DC current is determined by measuring a voltage drop across a parallel shunt resistor, then converted to a final analog voltage...

The KR Sense 90A is a small voltage and current sense breakout board. DC current is determined by measuring a voltage drop across a parallel shunt resistor, then converted to a final analog voltage output by the INA-169. Voltage sense is accomplished by scaling to 3.3V ADC range by a precision resistor divider. This version of the sensor features a maximum voltage tolerance of 51.8 Volts at 89.4 Amps, to be exact. Please be aware that KR Sense boards are supplied without leads or connectors....

We've all been there; you load up your project with a bunch of LEDs, only to discover that none have the same brightnesses. Some are way too dim to see, while others require sunglasses to not be...

We've all been there; you load up your project with a bunch of LEDs, only to discover that none have the same brightnesses. Some are way too dim to see, while others require sunglasses to not be blinded! Even we have experienced this problem with prototypes, so we recently standardized all resistor values for each of our LEDs (you can read more about that process in this blog post). In the process, we created this board to test each of our LEDs side by side. We realized that our customers...

The Leopard Imaging Camera is a 136° FOV (field of view) wide angle camera module that is great for machine vision applications, and designed specifically to be compatible with the NVIDIA Jetson...

The Leopard Imaging Camera is a 136° FOV (field of view) wide angle camera module that is great for machine vision applications, and designed specifically to be compatible with the NVIDIA Jetson Nano Developer Kit. This camera incorporates a Sony IMX219 8.08MP color sensor, a fixed focus (M8) lens, and utilizes CSI-2 MIPI 2-lane data output interface. This is the same camera that we include in the SparkFun Jetbot v2.1 Kit. Note: SparkFun has not established the compatibility of this camera...

This is a BH1750 light intensity sensor breakout board with a 16 bit AD converter built-in which can directly output a digital signal, there is no need for complicated calculations. This is a more...

This is a BH1750 light intensity sensor breakout board with a 16 bit AD converter built-in which can directly output a digital signal, there is no need for complicated calculations. This is a more acurate and easier to use version of the simple foto resistor which only outputs a voltage that needs to be calculated in order to obtain meaningful data. With the BH1750 Light Sensor intensity can be directly measured by the luxmeter, without needing to make calculations. The data which is output by...

This is a three axis accelerometer for the LilyPad system. Based on the ADXL335 accelerometer from Analog Devices, the LilyPad Accelerometer can detect joint movement as well as inclination and...

This is a three axis accelerometer for the LilyPad system. Based on the ADXL335 accelerometer from Analog Devices, the LilyPad Accelerometer can detect joint movement as well as inclination and vibration.The ADXL335 outputs a 0V to 3V analog signal on each of the X, Y, and Z axis. You will need to convert this analog voltage to a gravity amount and use trigonometry to calculate a true 'angle'. If you are not looking for tilt, it is very easy to use this sensor for basic motion sensing.LilyPad...

A line follower sensor gives your robot the ability to detect lines or nearby objects. The sensor works by detecting reflected light coming from its own infrared LED. By measuring the amount of...

A line follower sensor gives your robot the ability to detect lines or nearby objects. The sensor works by detecting reflected light coming from its own infrared LED. By measuring the amount of reflected infrared light, it can detect transitions from light to dark (lines) or even objects directly in front of it. Light-colored surfaces will reflect more light than dark surfaces, resulting in their appearing brighter to the sensor. This allows the sensor to detect a dark line on a pale surface,...

This straight bar load cell (sometimes called a strain gauge) can translate up to 10kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that...

This straight bar load cell (sometimes called a strain gauge) can translate up to 10kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to the bar. With this gauge you will be able to tell just how heavy an object is, if an object's weight changes over time, or if you simply need to sense the presence of an object by measuring strain or load...

This is the Logitech C270 Webcam. With a sleek compact look and a black finish, this is not just for looks. This economical choice provides a 720p/30FPS HD resolution in a 16:9 widescreen format....

This is the Logitech C270 Webcam. With a sleek compact look and a black finish, this is not just for looks. This economical choice provides a 720p/30FPS HD resolution in a 16:9 widescreen format. The Logitech C270 webcam is compatible with most major messaging applications like Skype, Windows Live Messenger, Yahoo Messenger and more, giving you a wide selection of use. Fluid Crystal technology provides smoother videos, sharper pictures, richer colors and clearer sound in real-world conditions....

The Oak-1 is an all-in-one machine vision solution. It’s a 4-trillion-operations-per-second AI powerhouse that performs your AI models on-board, so that your host is free to do whatever you need it...

The Oak-1 is an all-in-one machine vision solution. It’s a 4-trillion-operations-per-second AI powerhouse that performs your AI models on-board, so that your host is free to do whatever you need it to do. Its integrated 12 MegaPixel camera module communicates over an on-board 2.1 Gbps MIPI interface directly to the Myriad X, which ingests this data and performs neural inference on it, returning the results over USB. Such a data path offloads the host processor from all of this work. In the...

This Oak-D DepthAI variant interfaces over USB3C to the host, allowing use with your (embedded) host platform of choice, including the Raspberry Pi and other popular embedded hosts. DepthAI is built...

This Oak-D DepthAI variant interfaces over USB3C to the host, allowing use with your (embedded) host platform of choice, including the Raspberry Pi and other popular embedded hosts. DepthAI is built to allow the power of Spatial AI to be embedded into products. The DepthAI hardware, firmware, and software suite combine depth perception, object detection (neural inference), and object tracking and gives you this power in a simple, easy-to-use Python API. This Oak-D variant of DepthAI allows the...

The Oak-D LITE takes the appealing characteristics of the Oak-D and makes them even better. The smaller and more affordable Oak-D LITE can still be considered the swiss army knife of computer...

The Oak-D LITE takes the appealing characteristics of the Oak-D and makes them even better. The smaller and more affordable Oak-D LITE can still be considered the swiss army knife of computer vision. The main difference between the D and the D LITE are lower resolution mono-cameras, no IMU on board, and no power adapter. For most use cases of the Oak-D LITE, the USB Type C port should supply enough power (a Y-adapter is available through Luxonis should extra power be needed). Much like the...

The OAK-D-IoT-40 is an Embedded/IoT version of the OAK-D imaginf platform from Luxonis. This sensor can be used completely standalone or via USB with a host like normal USB-only variants of DepthAI....

The OAK-D-IoT-40 is an Embedded/IoT version of the OAK-D imaginf platform from Luxonis. This sensor can be used completely standalone or via USB with a host like normal USB-only variants of DepthAI. It has a built-in ESP32 which provides WiFi, Bluetooth® (including BLE), as well as other interfaces. This OAK-SOM-IoT system on module is what powers this OAK-D model. This modular design allows you to leverage its open-source designs to embed the power of OAK-D into your own products and/or...

This is the 8mm M-12 mount standard lens for use with the Raspberry Pi HQ Camera Module M-12. The lens produces a 12MP picture with a 56° field of view in a 1in image format and is easily...

This is the 8mm M-12 mount standard lens for use with the Raspberry Pi HQ Camera Module M-12. The lens produces a 12MP picture with a 56° field of view in a 1in image format and is easily interchangeable using the thumb screw and adapter included with the Pi HQ Camera Module. This lens excels in use for portraits and machine vision applications.

This is the 25mm M-12 mount telephoto lens for use with the Raspberry Pi HQ Camera Module M-12. The lens produces a 5MP picture with a 18° field of view in a 1in image format and is easily...

This is the 25mm M-12 mount telephoto lens for use with the Raspberry Pi HQ Camera Module M-12. The lens produces a 5MP picture with a 18° field of view in a 1in image format and is easily interchangeable using the thumb screw and adapter included with the Pi HQ Camera Module. This telephoto lens excels when taking distance photos or close up photo. This lens can be used as a great accessory for time lapse photography, night sky, or landscape photography. Also, equally applicable to the 6mm...

The FS2012 mass flow sensor module measures the flow across a sensing surface using the thermo-transfer (calorimetric) principle and is capable of measuring gas or liquid medium. Some key advantages...

The FS2012 mass flow sensor module measures the flow across a sensing surface using the thermo-transfer (calorimetric) principle and is capable of measuring gas or liquid medium. Some key advantages over other flow solutions The sensor utilizes series of MEMS thermocouples, which provide excellent signal-to-noise ratio. The solid thermal isolation along with the silicon-carbide film coating offers excellent abrasive wear resistance and long-term reliability. The high temperature material used...

This is a medium size breadboard with 600 tie points. It has strong, self-adhesive backing. It is ideal for high frequency and low noise circuits. |Specification| Size:170*65mm (6.7x2.6 in) Suitable...

This is a medium size breadboard with 600 tie points. It has strong, self-adhesive backing. It is ideal for high frequency and low noise circuits. |Specification| Size:170*65mm (6.7x2.6 in) Suitable for 0.3-0.8 mm (0.01x0.03 in) wire|ShippingList| Medium Bread Board Self Adhsive x1

This miniature straight bar load cell (sometimes called a strain gauge) can translate up to 100g of pressure (force) into an electrical signal. Each load cell is able to measure the electrical...

This miniature straight bar load cell (sometimes called a strain gauge) can translate up to 100g of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to the bar. With this gauge you will be able to tell just how heavy an object is, if an object's weight changes over time, or if you simply need to sense the presence of an object by measuring strain...