All Items
In Stock

Products 1-6 of 6
Show

9V Snap Connector

Stocked-NoBackOrder
Availability: Stocked-NoBackOrder
Item #: PRT-00091 -
Price: $2.25 inc GST
Sparkfun

Classic 9V snap connector terminated with 2-pin polarized Molex connector with 0.1" spacing. The cable is 26AWG and is 5" in length.

Classic 9V snap connector terminated with 2-pin polarized Molex connector with 0.1" spacing. The cable is 26AWG and is 5" in length.

Battery Holder - 4xAA to Barrel Jack Connector

Stocked-NoBackOrder
Availability: Stocked-NoBackOrder
Item #: PRT-09835 -
Price: $5.32 inc GST
Sparkfun

This is a simple 4 cell AA battery holder. The 5 inch cable is terminated with a standard 5.5x2.1mm, center positive barrel jack connector. The connector mates with the barrel jack on the Arduino...

This is a simple 4 cell AA battery holder. The 5 inch cable is terminated with a standard 5.5x2.1mm, center positive barrel jack connector. The connector mates with the barrel jack on the Arduino (among a number of other products) allowing you to easily make your project battery powered. Note: the average voltage regulator has about 1V of dropout (but can vary greatly). This pack, with normal alkaline batteries, will output ~5.5V causing a normal 5V board to run at around 4 to 4.5V. This...

Battery Holder 2xAA with Cover and Switch

Stocked-NoBackOrder
Availability: Stocked-NoBackOrder
Item #: PRT-09547 -
Price: $2.71 inc GST
Sparkfun

This 2xAA battery holder puts a nice finishing touch on your battery powered project. This holder features a removable, sliding cover, which is secured with a small phillips head screw. Another...

This 2xAA battery holder puts a nice finishing touch on your battery powered project. This holder features a removable, sliding cover, which is secured with a small phillips head screw. Another bonus is the ON/OFF switch which can be used to control power to your project. The leads are about 150mm, and the last 5mm of them are tinned. Features: 67.9 x 32.8 x 18.25mm

Battery Holder 2xAA with Cover and Switch - JST Connector

Stocked-NoBackOrder
Availability: Stocked-NoBackOrder
Item #: PRT-09925 -
Price: $2.77 inc GST
Sparkfun

This 2xAA battery holder puts a nice finishing touch on your battery powered project. This holder features a removable, sliding cover, which is secured with a small Phillips head screw. Another...

This 2xAA battery holder puts a nice finishing touch on your battery powered project. This holder features a removable, sliding cover, which is secured with a small Phillips head screw. Another bonus is the ON/OFF switch which can be used to control power to your project. The leads are about 150mm and are terminated with a JST-XH (2.50mm pitch) connector. Note: This battery holder is NOT compatible with the micro:bit. The micro:bit, Arduino Pro, and other boards utilize a JST-PH connector, not...

Coin Cell Battery Holder - 20mm (SMD)

Stocked-NoBackOrder
Availability: Stocked-NoBackOrder
Item #: PRT-11892 -
Price: $2.22 inc GST
Sparkfun

Now for all of your coin cell battery surface mount needs, the 20mm SMD Coin Cell Holder. This holder fits our 20mm Lithium Ion coin cell battery and holds the battery in place with friction. The...

Now for all of your coin cell battery surface mount needs, the 20mm SMD Coin Cell Holder. This holder fits our 20mm Lithium Ion coin cell battery and holds the battery in place with friction. The metal housing connects to the positive (+) side of the battery and the PCB pad underneath is connected to the negative (-) side. Documents: Datasheet

micro:bit Battery Holder - 2xAAA (JST-PH)

Stocked-NoBackOrder
Availability: Stocked-NoBackOrder
Item #: PRT-15101 -
Price: $3.97 inc GST
Sparkfun

This is a unique two-cell AAA battery holder built specifically for the BBC micro:bit. The 6" (~150mm) cable has been terminated with a JST-PH connector. The connector mates the JST socket on the...

This is a unique two-cell AAA battery holder built specifically for the BBC micro:bit. The 6" (~150mm) cable has been terminated with a JST-PH connector. The connector mates the JST socket on the micro:bit perfectly, allowing you to easily make your project battery powered. Note: Please keep in mind that JST connectors are not suited for constant and repeated removal and insertions and may wear out over time. ...