Products 1-21 of 21
Show
2.4GHz Antenna - Adhesive (U.FL Connector)
Price: $10.59
View
Availability: Out of Stock
Sparkfun Item #: WRL-11320 -

This adhesive, omni-directional antenna is perfect for situations when you're trying to get a signal out from a transmitter that you've jammed down into an enclosure. Operating on the 2.4GHz band, it works great for WiFi, Bluetooth or ZigBee. Just connect the antenna using the attached U.FL connector and then peel and stick! Features: Type: Omni-Directional Dual Frequency Range: 2300 to 3800MHz & 5150 to 5875MHz Impedance: 50 Ohm Maximum VSWR: 3 Typical Gain: 2(Max) dB 41 x 30mm, 350mm cable...

2.4GHz Ceramic Chip Antenna
OOD!
Price: $5.30
View
Availability: Back Order
Sparkfun Item #: WRL-00144 -

2.4GHz ceramic chip antennas. Very small antennas that work nicely with the Nordic ICs. Don't expect these little guys to perform as well as their ~2" rubber duck counter parts, but then again, these will squeeze onto* any* PCB layout. Features: 2.2x6.5mm Documents: chip-antenna-2.4ghz.pdf

2.4GHz Duck Antenna RP-SMA
OOD!
Price: $14.04
View
Availability: Back Order
Sparkfun Item #: WRL-00145 -

2.4GHz Duck Antenna 2.2dBi with Reverse Polarized - SMA RF connector. Perfect for prototyping with our RF ICs. 50 ohm impedance. 4" long. Not sure which RF connector you need on your antenna? Check out our RF Connector Guide Documents: Datasheet RF Connector Buying Guide ...

2.4GHz Duck Antenna RP-SMA - Large
Price: $17.96
View
Availability: Stocked
Sparkfun Item #: WRL-00558 -

Need range? 2.4GHz Large Duck Antenna 5dBi with Reverse Polarized - SMA RF connector. Perfect for prototyping with our RF ICs. 50 ohm impedance. This antenna mates nicely with the Reverse Polarized SMA Connector. Features: 0.5x7.7" Documents: Datasheet

900/1800MHz Dual Frequency Duck Antenna RP-SMA
OOD!
Price: $14.04
View
Availability: Back Order
Sparkfun Item #: WRL-09143 -

900/1800 MHz Duck Antenna 2dBi with regular RP-SMA RF connector. Perfect for use with the XBee 900MHz units. 50 ohm impedance. 105mm long. Be sure to pick the antenna with the right connector. Almost all 2.4GHz and 915MHz antennas need to be RP-SMA. See our SMA Connector tutorial for a good visual aid. Documents: Datasheet

915MHz LoRa Antenna RP-SMA - 1/2 Wave 2dBi
OOD!
Price: $14.04
View
Availability: Back Order
Sparkfun Item #: WRL-14876 -

Increase your range with this 1/2 wave duck antenna. Designed for 860 to 960MHz it is ideal for distant LoRa nodes. Utilizes an RP-SMA connector and is 200mm long. Documents: 915MHz 1/2 Wave RP-SMA Antenna Datasheet

915MHz LoRa Antenna RP-SMA - 1/4 Wave 2dBi
OOD!
Price: $15.80
View
Availability: Back Order
Sparkfun Item #: WRL-14875 -

A small 1/4 wave rubber duck antenna for LoRa or other 860-960MHz communication. Antenna has a center frequency of 915MHz and utilizes an RP-SMA connector. Gain is 2dBi with an overall length of 110mm.

Interface Cable for TNC to RP-SMA - 1m
OOD!
Price: $11.11
View
Availability: Back Order
Sparkfun Item #: CAB-14132 -

This is a very simple 1m long TNC to RP-SMA cable. We like to use this cable to connect our ultra high-frequency RFID antennas to an equally powerful reader board. This cable is perfect for extending pre-existing cables to give yourself a better range of operations when managing your RFID projects. Each cable is capable of a nominal impedance of 50Ī© with a cutoff frequency of 39GHz. If you are looking for a good antenna to pair this cable with, we recommend our UHF RFID Antenna. Note: If you...

Interface Cable N to RP-SMA Cable - 1m
OOD!
Price: $14.04
View
Availability: Back Order
Sparkfun Item #: CAB-14911 -

This connector cable interfaces N type female to RP-SMA male. Primarily used to connect our larger 915MHz LoRa antenna to RP-SMA connections but can be used on other devices up to 3GHz. Cable type is RG316. Length is 1m.

Interface Cable RP-SMA to U.FL
Price: $8.94
View
Availability: Stocked
Sparkfun Item #: WRL-00662 -

Commonly used to attach WiFi, Bluetooth, or nRFxxx based devices to a 2.4GHz antenna. Features: 4" Length Documents: Datasheet RF Connector Buying Guide

Iridium Certified Passive Antenna
OOD!
Price: $149.06
View
Availability: Back Order
Sparkfun Item #: SPX-15789 -

The M1621HCT-P-SMA is a high performance Iridium Certified passive antenna designed for wireless applications. The antenna is built on proprietary Maxtena HelicoreĀ® technology. This technology provides exceptional pattern control, polarization purity and high efficiency in a very compact form factor. This antenna operates at 1621 MHz at 60% efficiency.The M1621HCT-P-SMA is a screw-on design, featuring an integrated SMA connector and is rated IP-67 when mounted for added protection. This...

LoRa Fiberglass Antenna Type N - 5.8dBi (860-930MHz)
OOD!
Price: $91.80
View
Availability: Back Order
Sparkfun Item #: WRL-15597 -

If you need maximum distance for your LoRa project you need this incredibly durable, outdoor antenna with 5.8dBi gain. This 860-930MHz antenna is 90cm / 35.5" long and includes hardware for pole mounting. Made of fiberglass and aluminum this antenna is ideal for heavy-duty and high-power LoRa base stations but can be used with LoRa nodes as well. Antenna has a type N male termination. When mounted vertically this shrouded connector helps prevent against water and weather build-up on the...

Pycom LoRa and Sigfox Antenna Kit - 915MHz
OOD!
Price: $27.43
View
Availability: Back Order
Sparkfun Item #: WRL-14676 -

If you intend on using the LoRa or Sigfox connectivity on the LoPy4 you are going to need to connect a special antenna before beforehand otherwise you risk damaging the device. Luckily, with this Antenna Kit from Pycom, you won't need to worry about hurting your fancy LoPy4. This universal LoRa and Sigfox Antenna Kit can also be used with LoPy, SiPy, and FiPy IoT development boards on top of the LoPy4. Included in this kit is a tilt swivel 1/2 wave whip antenna with a male RP-SMA connector, a...

Reverse Polarized SMA Connector
OOD!
Price: $3.44
View
Availability: Back Order
Sparkfun Item #: WRL-00592 -

PCB edge mount Reverse Polarized - SMA RF connector. Perfect for prototyping with our RF ICs. This is a standard edge connector. The thickness between pins is 0.063" so that it can slide sideways onto a PCB. See the mechanical drawing to create your footprint. Supported Antennae: Any antenna that follows the reverse polarized SMA convention. These are the most common 2.4GHz antennas you'll find. Be sure to check out the SMA connector tutorial here for more information on SMA connectors....

RPSMA Male to SMA Female Adapter
OOD!
Price: $3.97
View
Availability: Back Order
Sparkfun Item #: WRL-09232 -

This is an adapter that converts an RP-SMA board to an SMA antenna. The adapter will connect to any of our 2.4GHz wireless boards (Bluetooth, Nordic, or XBee) or interface cables and will allow you to use an antenna/cable with an SMA connection. You should not need this adapter with any of our antennas or dev boards. These adapters are listed only to help SparkFun users that have rare or odd antenna coupling needs. Be sure to check out the SMA connector tutorial here for more information on...

SMA Connector
OOD!
Price: $3.44
View
Availability: Back Order
Sparkfun Item #: WRL-00593 -

PCB edge mount - SMA RF connector. Perfect for prototyping with the GPS and Cellular devices that require an antenna connection. These connectors have a female signal pin and will correctly mate with the original SMA type antennas. Documents: Datasheet SMA Tutorial

SMA Male to RPSMA Male Adapter
OOD!
Price: $3.97
View
Availability: Back Order
Sparkfun Item #: WRL-09233 -

This is an inner thread (outer nut) adapter that will connect to any of our wireless boards or interface cables and allow you to use an antenna/cable that has an outer thread configuration. You should not need this adapter with any of our antennas or dev boards. These adapters are listed only to help SparkFun users that have rare or odd antenna coupling needs. Be sure to check out the SMA connector tutorial here for more information on SMA connectors. Supported Connections: Any RP-SMA or SMA...

Telescopic Antenna SMA - 300 MHz to 1.1 GHz (ANT700)
Price: $45.90
View
Availability: Out of Stock
Sparkfun Item #: WRL-13982 -

This ANT700 is a telescopic antenna designed for operation from 300 MHz to 1.1 GHz with a total length that is configurable from 9.5 cm to 24.5 cm. Each ANT700 is constructed of stainless steel and features an SMA male connector, rotating shaft, and adjustable elbow. The ANT700 is a 50 Ohm antenna designed to match HackRF One. It is the perfect first antenna for general purpose use with HackRF One, but we won't stop you from using it with different projects! Documents: Product Page ...

Telescopic Antenna SMA - 75 MHz to 1 GHz (ANT500)
OOD!
Price: $57.38
View
Availability: Back Order
Sparkfun Item #: WRL-13002 -

This ANT500 is a telescopic antenna designed for operation from 75 MHz to 1 GHz with a total length that is configurable from 20 cm to 88 cm long. Each ANT500 is constructed of stainless steel and features an SMA male connector, rotating shaft, and adjustable elbow. The ANT500 is a 50 ohm antenna designed to match HackRF One. It is the perfect first antenna for general purpose use with HackRF One but we won't stop you from using it with different projects! Documents: Product Page Product Video ...

U.FL SMD Connector
OOD!
Price: $2.65
View
Availability: Back Order
Sparkfun Item #: WRL-09144 -

Itty-bitty U.FL SMD connector. Great for tight PCB layouts that require antenna connections. Documents: Datasheet

UHF RFID Antenna (TNC)
OOD!
Price: $73.97
View
Availability: Back Order
Sparkfun Item #: WRL-14131 -

This is your solution when you absolutely, positively need to get the most out of an antenna for your next RFID project. This ultra high-frequency (UHF) RFID Antenna boasts a frequency range of 860-960 MHz with a gain of 6dBi. This is the same external antenna we use for our Simultaneous RFID Reader due to its high-quality features. Each UHF RFID Antenna is terminated with a 30cm long TNC Female RP cable. If you need to extend the cable attached to the antenna, we offer additional cords to...