Wireless and IoT Antennas

2.4GHz ceramic chip antennas. Very small antennas that work nicely with the Nordic ICs. Don't expect these little guys to perform as well as their ~2" rubber duck counter parts, but then again,...

2.4GHz ceramic chip antennas. Very small antennas that work nicely with the Nordic ICs. Don't expect these little guys to perform as well as their ~2" rubber duck counter parts, but then again, these will squeeze onto* any* PCB layout. Features: 2.2x6.5mm Documents: chip-antenna-2.4ghz.pdf

2.4GHz Duck Antenna 2.2dBi with Reverse Polarized - SMA RF connector. Perfect for prototyping with our RF ICs. 50 ohm impedance. 4" long. Not sure which RF connector you need on your antenna? Check...

2.4GHz Duck Antenna 2.2dBi with Reverse Polarized - SMA RF connector. Perfect for prototyping with our RF ICs. 50 ohm impedance. 4" long. Not sure which RF connector you need on your antenna? Check out our RF Connector Guide Documents: Datasheet RF Connector Buying Guide ...

Need range? 2.4GHz Large Duck Antenna 5dBi with Reverse Polarized - SMA RF connector. Perfect for prototyping with our RF ICs. 50 ohm impedance. This antenna mates nicely with the Reverse Polarized...

Need range? 2.4GHz Large Duck Antenna 5dBi with Reverse Polarized - SMA RF connector. Perfect for prototyping with our RF ICs. 50 ohm impedance. This antenna mates nicely with the Reverse Polarized SMA Connector. Features: 0.5x7.7" Documents: Datasheet

Molex LTE/5G Cellular External Antennas are designed for 2G/3G/4G/5G modules and devices. The hinged type antennas offer excellent coverage and reliability with high efficiency and peak gain. The...

Molex LTE/5G Cellular External Antennas are designed for 2G/3G/4G/5G modules and devices. The hinged type antennas offer excellent coverage and reliability with high efficiency and peak gain. The series offers design flexibility with connectors in straight and folded modes with SMA-J and RP-SMA-J mounting options. LTE/5G Cellular Antennas are offered in both black/white and male/female and are ideal for various wireless and networking applications. Features: Minimum Frequency: 698 MHz Maximum...

900/1800 MHz Duck Antenna 2dBi with regular RP-SMA RF connector. Perfect for use with the XBee 900MHz units. 50 ohm impedance. 105mm long. Be sure to pick the antenna with the right connector....

900/1800 MHz Duck Antenna 2dBi with regular RP-SMA RF connector. Perfect for use with the XBee 900MHz units. 50 ohm impedance. 105mm long. Be sure to pick the antenna with the right connector. Almost all 2.4GHz and 915MHz antennas need to be RP-SMA. See our SMA Connector tutorial for a good visual aid. Documents: Datasheet

This adhesive, dual band antenna is perfect for situations when you're trying to get a signal out from a transmitter that you've jammed down into an enclosure. Operating on the 2.4GHz or 5.8GHz...

This adhesive, dual band antenna is perfect for situations when you're trying to get a signal out from a transmitter that you've jammed down into an enclosure. Operating on the 2.4GHz or 5.8GHz band, it works great for WiFi, Bluetooth or ZigBee. Just connect the antenna using the attached U.FL connector and then peel and stick! Features: Frequency range: 2400-2500Mhz/5150-5850Mhz Gain: 8dBi internal antenna VSWR: ≤1.8 Polarization: Vertical Input impedance: 50Ω Power: 30w Size: 95x13x1mm Cable...

SMA to MMCX Connector. Adapts MMCX jack to a standard SMA bulkhead. This cable interfaces to the GM862 Cellular modules and the PG31 GPS module. **Length: **6" (6.7" including the MMCX and SMA...

SMA to MMCX Connector. Adapts MMCX jack to a standard SMA bulkhead. This cable interfaces to the GM862 Cellular modules and the PG31 GPS module. **Length: **6" (6.7" including the MMCX and SMA connectors)

This connector cable interfaces N type female to RP-SMA male. Primarily used to connect our larger 915MHz LoRa antenna to RP-SMA connections but can be used on other devices up to 3GHz. Cable type...

This connector cable interfaces N type female to RP-SMA male. Primarily used to connect our larger 915MHz LoRa antenna to RP-SMA connections but can be used on other devices up to 3GHz. Cable type is RG316. Length is 1m.

Commonly used to attach WiFi, Bluetooth, or nRFxxx based devices to a 2.4GHz antenna. Features: 4" Length Documents: Datasheet RF Connector Buying Guide ...

Commonly used to attach WiFi, Bluetooth, or nRFxxx based devices to a 2.4GHz antenna. Features: 4" Length Documents: Datasheet RF Connector Buying Guide

This is a 4" connector cable that interfaces U.FL RF connectors to regular SMA connectors. This cable is commonly used to connect larger GPS antennas and quad-band cellular antennas. Documents:...

This is a 4" connector cable that interfaces U.FL RF connectors to regular SMA connectors. This cable is commonly used to connect larger GPS antennas and quad-band cellular antennas. Documents: Datasheet RF Connector Buying Guide

A U.FL to SMA (jack) bulkhead straight connector with a 1.32 mm diameter cable. Less than -2 dB cable insertion loss up to 6 GHz. Both connectors are gold-plated brass and the cable conductor is...

A U.FL to SMA (jack) bulkhead straight connector with a 1.32 mm diameter cable. Less than -2 dB cable insertion loss up to 6 GHz. Both connectors are gold-plated brass and the cable conductor is silver-coated copper. Includes: 1x U.FL to SMA cable 1x Locking Nut and Bulkhead Washer Features: Connector A Series: SMA Connector A Gender: Jack (Female) Connector A Body Style: Bulkhead Connector B Series: U.FL Connector B Gender: Plug (Male) Connector B Body Style: Right Angle Cable Length: 100...

If you need maximum distance for your LoRa project you need this incredibly durable, outdoor antenna with 5.8dBi gain. This 860-930MHz antenna is 90cm / 35.5" long and includes hardware for pole...

If you need maximum distance for your LoRa project you need this incredibly durable, outdoor antenna with 5.8dBi gain. This 860-930MHz antenna is 90cm / 35.5" long and includes hardware for pole mounting. Made of fiberglass and aluminum this antenna is ideal for heavy-duty and high-power LoRa base stations but can be used with LoRa nodes as well. Antenna has a type N male termination. When mounted vertically this shrouded connector helps prevent against water and weather build-up on the...

If you need maximum distance for your LoRa project you need this incredibly durable, outdoor antenna with 5.8dBi gain. This 863-870MHz antenna is 90cm / 35.5" long and includes hardware for pole...

If you need maximum distance for your LoRa project you need this incredibly durable, outdoor antenna with 5.8dBi gain. This 863-870MHz antenna is 90cm / 35.5" long and includes hardware for pole mounting. Made of fiberglass and aluminum this antenna is ideal for heavy-duty and high-power LoRa base stations but can be used with LoRa nodes as well. Antenna has a type N male termination. When mounted vertically this shrouded connector helps prevent against water and weather build-up on the...

This small form-factor antenna offers a 2.4GHz frequency range. These antennas offer adhesive backing that simplifies mounting within the device for a FPC or PCB. Just connect the antenna using the...

This small form-factor antenna offers a 2.4GHz frequency range. These antennas offer adhesive backing that simplifies mounting within the device for a FPC or PCB. Just connect the antenna using the attached U.FL connector and then peel and stick! Features: Frequency range: 2400-2500Mhz Polarization: Vertical Input impedance: 50Ω Power: 30w Size: 50x10x1mm Cable length: 100mm Cable type: 1.13 coix cable Connector: U.FL Mounting : 3M sticker Operation Temperature: - 30 °C ~ + 65 °C Storage...

PCB edge mount Reverse Polarized - SMA RF connector. Perfect for prototyping with our RF ICs. This is a standard edge connector. The thickness between pins is 0.063" so that it can slide sideways...

PCB edge mount Reverse Polarized - SMA RF connector. Perfect for prototyping with our RF ICs. This is a standard edge connector. The thickness between pins is 0.063" so that it can slide sideways onto a PCB. See the mechanical drawing to create your footprint. Supported Antennae: Any antenna that follows the reverse polarized SMA convention. These are the most common 2.4GHz antennas you'll find. Be sure to check out the SMA connector tutorial here for more information on SMA connectors....

This RP-SMA to U.FL Cable is commonly used to attach WiFi, Bluetooth, or nRFxxx based devices to a 2.4GHz antenna. What makes this unassuming cable special is the slightly longer length of 150mm...

This RP-SMA to U.FL Cable is commonly used to attach WiFi, Bluetooth, or nRFxxx based devices to a 2.4GHz antenna. What makes this unassuming cable special is the slightly longer length of 150mm (compared to 100mm). We found that the extra 50mm makes all the difference when working with an enclosure. Features: U.FL Termination RP-SMA Termination 150mm Length Documents: RF Connector Buying Guide ...

This is an adapter that converts an RP-SMA board to an SMA antenna. The adapter will connect to any of our 2.4GHz wireless boards (Bluetooth, Nordic, or XBee) or interface cables and will allow you...

This is an adapter that converts an RP-SMA board to an SMA antenna. The adapter will connect to any of our 2.4GHz wireless boards (Bluetooth, Nordic, or XBee) or interface cables and will allow you to use an antenna/cable with an SMA connection. You should not need this adapter with any of our antennas or dev boards. These adapters are listed only to help SparkFun users that have rare or odd antenna coupling needs. Be sure to check out the SMA connector tutorial here for more information on...

PCB edge mount - SMA RF connector. Perfect for prototyping with the GPS and Cellular devices that require an antenna connection. These connectors have a female signal pin and will correctly mate...

PCB edge mount - SMA RF connector. Perfect for prototyping with the GPS and Cellular devices that require an antenna connection. These connectors have a female signal pin and will correctly mate with the original SMA type antennas. Documents: Datasheet SMA Tutorial

This is an inner thread (outer nut) adapter that will connect to any of our wireless boards or interface cables and allow you to use an antenna/cable that has an outer thread configuration. You...

This is an inner thread (outer nut) adapter that will connect to any of our wireless boards or interface cables and allow you to use an antenna/cable that has an outer thread configuration. You should not need this adapter with any of our antennas or dev boards. These adapters are listed only to help SparkFun users that have rare or odd antenna coupling needs. Be sure to check out the SMA connector tutorial here for more information on SMA connectors. Supported Connections: Any RP-SMA or SMA...

This SMA to U.FL Cable is commonly used to attach WiFi, Bluetooth, or nRFxxx based devices to a 2.4GHz antenna. What makes this unassuming cable special is the slightly longer length of 150mm...

This SMA to U.FL Cable is commonly used to attach WiFi, Bluetooth, or nRFxxx based devices to a 2.4GHz antenna. What makes this unassuming cable special is the slightly longer length of 150mm (compared to 100mm). We found that the extra 50mm makes all the difference when working with an enclosure. Features: U.FL Termination SMA Termination 150mm Length Documents: RF Connector Buying Guide ...

The Taoglas Steedan MA350 is a 5-in-1 next-generation low profile magnetic mount antenna for a vehicle, outdoor building, and heavy equipment roof applications. It has a fully IP65 rated waterproof...

The Taoglas Steedan MA350 is a 5-in-1 next-generation low profile magnetic mount antenna for a vehicle, outdoor building, and heavy equipment roof applications. It has a fully IP65 rated waterproof robust ABS enclosure and base. This is an ideal external combination antenna solution that is used where drilling a hole through the roof of a vehicle or a metal panel is not feasible. It can be mounted on steel surfaces and its ultra-strong neodymium magnets. A soft foam cushion on the base...

This ANT700 is a telescopic antenna designed for operation from 300 MHz to 1.1 GHz with a total length that is configurable from 9.5 cm to 24.5 cm. Each ANT700 is constructed of stainless steel and...

This ANT700 is a telescopic antenna designed for operation from 300 MHz to 1.1 GHz with a total length that is configurable from 9.5 cm to 24.5 cm. Each ANT700 is constructed of stainless steel and features an SMA male connector, rotating shaft, and adjustable elbow. The ANT700 is a 50 Ohm antenna designed to match HackRF One. It is the perfect first antenna for general purpose use with HackRF One, but we won't stop you from using it with different projects! Documents: Product Page ...

This ANT500 is a telescopic antenna designed for operation from 75 MHz to 1 GHz with a total length that is configurable from 20 cm to 88 cm long. Each ANT500 is constructed of stainless steel and...

This ANT500 is a telescopic antenna designed for operation from 75 MHz to 1 GHz with a total length that is configurable from 20 cm to 88 cm long. Each ANT500 is constructed of stainless steel and features an SMA male connector, rotating shaft, and adjustable elbow. The ANT500 is a 50 ohm antenna designed to match HackRF One. It is the perfect first antenna for general purpose use with HackRF One but we won't stop you from using it with different projects! Documents: Product Page Product Video ...

This is a 915MHz SMA Duck Antenna for use with the AHPI7292S WiFi HaLow HAT. We've distinguished it as for use with this HAT as it's an SMA connection where most of our other boards are RP-SMA. It's...

This is a 915MHz SMA Duck Antenna for use with the AHPI7292S WiFi HaLow HAT. We've distinguished it as for use with this HAT as it's an SMA connection where most of our other boards are RP-SMA. It's the easiest way to start working with the WiFi HaLow HAT with meaningful transmission distance (which will vary based on environmental conditions including line of sight). Features: 915Mhz Works with the WiFi HaLow HAT 2dBi Rated for indoor use Documents: Dimensional Drawing ...