Bambu Lab Accessories

Overview A small circuit board installed underneath the heatbed, which connects the heatbed sensors to the MC board. Installation Learn more about the replacement of the Heatbed Piezo Interface...

Overview A small circuit board installed underneath the heatbed, which connects the heatbed sensors to the MC board. Installation Learn more about the replacement of the Heatbed Piezo Interface Board for P1 Series and X1 Series on Bambu Lab Wiki.

The heatbed signal cable is a 6pin cable connected to the hotbed Sensor for temperature measurement and leveling. Compatibility X1 Series and P1 Series Replacement To learn more about replacing the...

The heatbed signal cable is a 6pin cable connected to the hotbed Sensor for temperature measurement and leveling. Compatibility X1 Series and P1 Series Replacement To learn more about replacing the heatbed signal cableX1 Series: https://wiki.bambulab.com/en/x1/maintenance/Replacing-the-heat-bed-cable.P1P: https://wiki.bambulab.com/en/p1/maintenance/heat-bed-signal-cable-p1p ...

Overview: The Bambu Lab Heatbed Unit is an essential spare part for enhancing your 3D printing experience. This unit ensures consistent and reliable heating, crucial for achieving precise and...

Overview: The Bambu Lab Heatbed Unit is an essential spare part for enhancing your 3D printing experience. This unit ensures consistent and reliable heating, crucial for achieving precise and high-quality prints.

Overview Replacement Heat Bed assembly for the Bambu Lab A1 Printer (post recall) Installation Learn more about the replacement of the heat bed unit for A1 on Bambu Lab Wiki Compatibility A1...

Overview Replacement Heat Bed assembly for the Bambu Lab A1 Printer (post recall) Installation Learn more about the replacement of the heat bed unit for A1 on Bambu Lab Wiki Compatibility A1 Exclusive In the Box 1 x Heat Bed Assembly with cables ...

Real High Flow: Save Up to 30% of Your Time The Bambu High Flow Nozzle's optimized melt zone enables significantly increased volumetric speed, achieving up to 62.5%1 higher max volumetric speed and...

Real High Flow: Save Up to 30% of Your Time The Bambu High Flow Nozzle's optimized melt zone enables significantly increased volumetric speed, achieving up to 62.5%1 higher max volumetric speed and reducing print time by up to 30%2 with ease. The larger your model, the more time you save—especially for prints with extensive infills. 1. Tested with ABS, Ø240mm single-wall cylinder, 0.2mm layer height, 1.0mm outer wall, 280℃ nozzle temperature, spiral vase mode on. 2. Tested with PLA Basic, 15%...

Bambu Lab High Flow Hotend for H2/P2S - 0.6 mm Real High Flow: Save Up to 30% of Your Time The Bambu High Flow Nozzle's optimized melt zone enables significantly increased volumetric speed,...

Bambu Lab High Flow Hotend for H2/P2S - 0.6 mm Real High Flow: Save Up to 30% of Your Time The Bambu High Flow Nozzle's optimized melt zone enables significantly increased volumetric speed, achieving up to 62.5%1 higher max volumetric speed and reducing print time by up to 30%2 with ease. The larger your model, the more time you save—especially for prints with extensive infills. 1. Tested with ABS, Ø240mm single-wall cylinder, 0.2mm layer height, 1.0mm outer wall, 280℃ nozzle temperature,...

Bambu Lab High Flow Hotend for H2/P2S - 0.8 mm Real High Flow: Save Up to 30% of Your Time The Bambu High Flow Nozzle's optimized melt zone enables significantly increased volumetric speed,...

Bambu Lab High Flow Hotend for H2/P2S - 0.8 mm Real High Flow: Save Up to 30% of Your Time The Bambu High Flow Nozzle's optimized melt zone enables significantly increased volumetric speed, achieving up to 62.5%1 higher max volumetric speed and reducing print time by up to 30%2 with ease. The larger your model, the more time you save—especially for prints with extensive infills. 1. Tested with ABS, Ø240mm single-wall cylinder, 0.2mm layer height, 1.0mm outer wall, 280℃ nozzle temperature,...

Bambu Lab High Flow Induction Hotend with Hardened Steel Nozzle - 0.4 mm - H2C Multi-Material Printing with Minimal Purge Waste In traditional single-nozzle multi-material printing, purging is...

Bambu Lab High Flow Induction Hotend with Hardened Steel Nozzle - 0.4 mm - H2C Multi-Material Printing with Minimal Purge Waste In traditional single-nozzle multi-material printing, purging is needed to clear leftover material between filament changes.Vortek changes that with an intelligent hotend-swapping system that replaces the entire hotend — delivering faster, cleaner prints with minimal waste. 8-Second Induction Heating Our industry-leading induction heating technology brings the nozzle...

Bambu Lab High Flow Induction Hotend with Hardened Steel Nozzle - 0.6 mm - H2C Multi-Material Printing with Minimal Purge Waste In traditional single-nozzle multi-material printing, purging is...

Bambu Lab High Flow Induction Hotend with Hardened Steel Nozzle - 0.6 mm - H2C Multi-Material Printing with Minimal Purge Waste In traditional single-nozzle multi-material printing, purging is needed to clear leftover material between filament changes.Vortek changes that with an intelligent hotend-swapping system that replaces the entire hotend — delivering faster, cleaner prints with minimal waste. 8-Second Induction Heating Our industry-leading induction heating technology brings the nozzle...

When you're finished printing, you will have a wide piece (1x), narrow piece (1x), spacing shim (2x).Find the locator (a tiny block on the wide piece). Align it with the notch on the inner ring of...

When you're finished printing, you will have a wide piece (1x), narrow piece (1x), spacing shim (2x).Find the locator (a tiny block on the wide piece). Align it with the notch on the inner ring of the filament roll. Insert the wide piece into the filament roll. Step 1. Insert the narrow piece and align the groove of each piece inside of the spool until it is pushed firmly into the wide piece. Step 2. Once it is pushed firmly into the wide piece, rotate the narrow piece clockwise until it...

Overview The Hotend Cooling Fan is used to cool down both the hotend heating assembly and the hotend. Installation Learn more about replacing the Hotend Cooling Fan on Bambu Lab Wiki. In the Box 1....

Overview The Hotend Cooling Fan is used to cool down both the hotend heating assembly and the hotend. Installation Learn more about replacing the Hotend Cooling Fan on Bambu Lab Wiki. In the Box 1. Hotend Cooling Fan * 12. BT2-4 Screws * 2 Compatibility A1 Series ...

Quick Swap Nozzle Design The special design of H2/P2S hotend heating assembly enables easy separation of the thermal and electronic components of the hotend. Simply unlock the latch for quick and...

Quick Swap Nozzle Design The special design of H2/P2S hotend heating assembly enables easy separation of the thermal and electronic components of the hotend. Simply unlock the latch for quick and easy hotend removal and installation. *Please ensure that the hotend has cooled down before swapping, and avoid touching the heat block (lower section of the hotend) to prevent any risk of burns. 0.2mm Nozzle - Optimal Print Fineness Smaller diameter extrudes thin filaments. High resolution on the...

Quick Swap Nozzle Design The special design of H2/P2S hotend heating assembly enables easy separation of the thermal and electronic components of the hotend. Simply unlock the latch for quick and...

Quick Swap Nozzle Design The special design of H2/P2S hotend heating assembly enables easy separation of the thermal and electronic components of the hotend. Simply unlock the latch for quick and easy hotend removal and installation. *Please ensure that the hotend has cooled down before swapping, and avoid touching the heat block (lower section of the hotend) to prevent any risk of burns. 0.2mm Nozzle - Optimal Print Fineness Smaller diameter extrudes thin filaments. High resolution on the...

Quick Swap Nozzle Design The special design of H2/P2S hotend heating assembly enables easy separation of the thermal and electronic components of the hotend. Simply unlock the latch for quick and...

Quick Swap Nozzle Design The special design of H2/P2S hotend heating assembly enables easy separation of the thermal and electronic components of the hotend. Simply unlock the latch for quick and easy hotend removal and installation. *Please ensure that the hotend has cooled down before swapping, and avoid touching the heat block (lower section of the hotend) to prevent any risk of burns. 0.2mm Nozzle - Optimal Print Fineness Smaller diameter extrudes thin filaments. High resolution on the...

Quick Swap Nozzle Design The special design of H2/P2S hotend heating assembly enables easy separation of the thermal and electronic components of the hotend. Simply unlock the latch for quick and...

Quick Swap Nozzle Design The special design of H2/P2S hotend heating assembly enables easy separation of the thermal and electronic components of the hotend. Simply unlock the latch for quick and easy hotend removal and installation. *Please ensure that the hotend has cooled down before swapping, and avoid touching the heat block (lower section of the hotend) to prevent any risk of burns. 0.2mm Nozzle - Optimal Print Fineness Smaller diameter extrudes thin filaments. High resolution on the...

Overview The Hotend Heating Assembly is specially designed to support the quick swap design of the hotend. A quick clamping mechanism is used to secure the heater block and heating base, enabling...

Overview The Hotend Heating Assembly is specially designed to support the quick swap design of the hotend. A quick clamping mechanism is used to secure the heater block and heating base, enabling easy separation of the thermal and electronic components of the hotend.The hotend heating assembly can heat the hotend up to 300℃ and measure the real-time temperature of the hotend with the included thermistor. Installation Learn more about replacing the Hotend Heating Assembly on Bambu Lab Wiki. In...

Bambu Lab Hotend Heating Assembly - H2S The Hotend Heating Assembly heats the hotend and uses a clamping mechanism to secure it, enabling quick removal for maintenance or replacement....

Bambu Lab Hotend Heating Assembly - H2S The Hotend Heating Assembly heats the hotend and uses a clamping mechanism to secure it, enabling quick removal for maintenance or replacement. Compatibility H2S and H2S Laser

Bambu Lab Hotend Heating Assembly - P2S An accessory installed on the toolhead, responsible for heating the printing materials to a molten state. Compatibility P2 Series ...

Bambu Lab Hotend Heating Assembly - P2S An accessory installed on the toolhead, responsible for heating the printing materials to a molten state. Compatibility P2 Series

The Hotend Silicone Sock is made from high-quality silicone for higher temperature resistance (rated to 300°C).The silicone sock provides optimal thermal insulation for the hotend to maintain a...

The Hotend Silicone Sock is made from high-quality silicone for higher temperature resistance (rated to 300°C).The silicone sock provides optimal thermal insulation for the hotend to maintain a consistent temperature during printing, while also offering long-lasting protection from filament being stuck to the hotend. Compatible with A1 Series Learn more about replacing the Hotend Silicone Sock on Bambu Lab Wiki. ...

Quick Swap Nozzle Design The special design of hotend heating assembly enables easy separation of the thermal and electronic components of the hotend. In addition, the magnetic block installed on...

Quick Swap Nozzle Design The special design of hotend heating assembly enables easy separation of the thermal and electronic components of the hotend. In addition, the magnetic block installed on the hotend heatsink enables quick and accurate fixation of the hotend to its precise mounting position. This feature enhances the convenience of quick swapping, allowing for easy removal and installation of the hotend. *Please ensure that the hotend has cooled down before swapping, and avoid touching...

Featured Bambu Lab Hotend with Hardened Steel - 0.4 mm Nozzle, A1 Series QUICK SWAP Quick Swap Nozzle Design The special design of hotend heating assembly enables easy separation of the thermal and...

Featured Bambu Lab Hotend with Hardened Steel - 0.4 mm Nozzle, A1 Series QUICK SWAP Quick Swap Nozzle Design The special design of hotend heating assembly enables easy separation of the thermal and electronic components of the hotend. In addition, the magnetic block installed on the hotend heatsink enables quick and accurate fixation of the hotend to its precise mounting position. This featureenhances the convenience of quick swapping, allowing foreasy removal and installationof the...

Featured Bambu Lab Hotend with Stainless Steel - 0.4 mm Nozzle, A1 Series QUICK SWAP Quick Swap Nozzle Design The special design of hotend heating assembly enables easy separation of the thermal and...

Featured Bambu Lab Hotend with Stainless Steel - 0.4 mm Nozzle, A1 Series QUICK SWAP Quick Swap Nozzle Design The special design of hotend heating assembly enables easy separation of the thermal and electronic components of the hotend. In addition, the magnetic block installed on the hotend heatsink enables quick and accurate fixation of the hotend to its precise mounting position. This featureenhances the convenience of quick swapping, allowing foreasy removal and installationof the...

Bambu Lab Induction Hotend with Hardened Steel Nozzle - 0.4 mm - H2C Multi-Material Printing with Minimal Purge Waste In traditional single-nozzle multi-material printing, purging is needed to clear...

Bambu Lab Induction Hotend with Hardened Steel Nozzle - 0.4 mm - H2C Multi-Material Printing with Minimal Purge Waste In traditional single-nozzle multi-material printing, purging is needed to clear leftover material between filament changes.Vortek changes that with an intelligent hotend-swapping system that replaces the entire hotend — delivering faster, cleaner prints with minimal waste. 8-Second Induction Heating Our industry-leading induction heating technology brings the nozzle to...

Bambu Lab Induction Hotend with Hardened Steel Nozzle - 0.6 mm - H2C Multi-Material Printing with Minimal Purge Waste In traditional single-nozzle multi-material printing, purging is needed to clear...

Bambu Lab Induction Hotend with Hardened Steel Nozzle - 0.6 mm - H2C Multi-Material Printing with Minimal Purge Waste In traditional single-nozzle multi-material printing, purging is needed to clear leftover material between filament changes.Vortek changes that with an intelligent hotend-swapping system that replaces the entire hotend — delivering faster, cleaner prints with minimal waste. 8-Second Induction Heating Our industry-leading induction heating technology brings the nozzle to...

Bambu Lab Induction Hotend with Hardened Steel Nozzle - 0.8 mm - H2C Multi-Material Printing with Minimal Purge Waste In traditional single-nozzle multi-material printing, purging is needed to clear...

Bambu Lab Induction Hotend with Hardened Steel Nozzle - 0.8 mm - H2C Multi-Material Printing with Minimal Purge Waste In traditional single-nozzle multi-material printing, purging is needed to clear leftover material between filament changes.Vortek changes that with an intelligent hotend-swapping system that replaces the entire hotend — delivering faster, cleaner prints with minimal waste. 8-Second Induction Heating Our industry-leading induction heating technology brings the nozzle to...

Bambu Lab Induction Hotend with Stainless Steel Nozzle - 0.2 mm - H2C Multi-Material Printing with Minimal Purge Waste In traditional single-nozzle multi-material printing, purging is needed to...

Bambu Lab Induction Hotend with Stainless Steel Nozzle - 0.2 mm - H2C Multi-Material Printing with Minimal Purge Waste In traditional single-nozzle multi-material printing, purging is needed to clear leftover material between filament changes.Vortek changes that with an intelligent hotend-swapping system that replaces the entire hotend — delivering faster, cleaner prints with minimal waste. 8-Second Induction Heating Our industry-leading induction heating technology brings the nozzle to...

Overview The Jet Engine Model Components Kit contains all the necessary hardware components for assembling a Jet Engine Model. To complete the assembly for an entirely functional piece, users also...

Overview The Jet Engine Model Components Kit contains all the necessary hardware components for assembling a Jet Engine Model. To complete the assembly for an entirely functional piece, users also need to download the model files and 3D print the remaining parts.Creator Program: The Creator Program is a collaborative program between Bambu Lab and creators. Creators unleash their creativity to design 3D printing models, while Bambu Lab provides compatible hardware kits for those designs....

Overview Laser Protective Goggles are highly effective in preventing accidental eye injuries caused by the laser of the H2D Laser module. For lasers with wavelengths ranging from 200 to 450 nm (the...

Overview Laser Protective Goggles are highly effective in preventing accidental eye injuries caused by the laser of the H2D Laser module. For lasers with wavelengths ranging from 200 to 450 nm (the H2D Laser emits a 450 nm blue laser), the protection level reaches OD5+, meaning that the laser power transmitted through the lenses is reduced to one hundred-thousandth of the original power. For lasers with wavelengths ranging from 900 to 1100 nm (primarily infrared light), the protection level...

Bambu Lab Laser Upgrade Kit - H2 Series The Bambu Lab Laser Upgrade Kit allows the use of the H2 Laser Modules for non-Laser enabled H2 Series 3D Printers. Can be integrated seamlessly with your...

Bambu Lab Laser Upgrade Kit - H2 Series The Bambu Lab Laser Upgrade Kit allows the use of the H2 Laser Modules for non-Laser enabled H2 Series 3D Printers. Can be integrated seamlessly with your current machine. Compatibility H2D and H2C

Overview The LED Lamp Kit contains all the necessary hardware components for assembling an LED Lamp. To complete the assembly for an entirely functional piece, users also need to download the model...

Overview The LED Lamp Kit contains all the necessary hardware components for assembling an LED Lamp. To complete the assembly for an entirely functional piece, users also need to download the model files and 3D print the remaining parts. Compatible ModelsCreatorsModel LinksEaster Bunny Egg LampNUKDDDEaster Bunny Egg Lamplampshade for LED Lamp Kitwuguiguilampshade for LED Lamp KitLED LampLin and Gleason (Bambu Lab)LED Lamp To download the model files of the LED Lamp and obtain detailed...

Bambu Lab LightGrip Cutting Mat Ideal for lighter materials such as regular cardstock and paper. Provides gentle adhesion for easy removal. Installation Learn more about the LightGrip Cutting Mat on...

Bambu Lab LightGrip Cutting Mat Ideal for lighter materials such as regular cardstock and paper. Provides gentle adhesion for easy removal. Installation Learn more about the LightGrip Cutting Mat on Bambu Lab Wiki. Compatibility H2D Laser ...

Overview The live view camera is a low-FPS camera included by default in the A1 mini. The chamber camera has three functions, which are Remote Livestreams and Time-lapses respectively. Remote...

Overview The live view camera is a low-FPS camera included by default in the A1 mini. The chamber camera has three functions, which are Remote Livestreams and Time-lapses respectively. Remote livestream: You can observe print progress anytime, anywhere.Time-lapses: This feature uses the chamber camera to automatically create time-lapse videos of prints. Compatibility A1 mini In the Box Live View Camera *1 Installation Learn more about the replacement of the Live View Camera for A1...

Important to know Lubricant Grease and Lubricant Oil can only used for A1 Series and can NOT be used on the X-axis carbon rods of the X1 and P1 Series.Theoretically, Lubricant Oil can also be used...

Important to know Lubricant Grease and Lubricant Oil can only used for A1 Series and can NOT be used on the X-axis carbon rods of the X1 and P1 Series.Theoretically, Lubricant Oil can also be used for lead screw lubrication, but since Lubricant Oil is prone to evaporation, this would require more frequent reapplication of the lubricant. Installation Learn more about the Lubricant Grease and Lubricant Oil - A1 Series on Bambu Lab Wiki.Compatibility A1 Series Exclusive ...

Start Your 3D Printing Journey with This Maker's Beginner Kit! Imagine having your own mini-factory at home, where you can create one-of-a-kind masterpieces! This accessory pack is your secret...

Start Your 3D Printing Journey with This Maker's Beginner Kit! Imagine having your own mini-factory at home, where you can create one-of-a-kind masterpieces! This accessory pack is your secret weapon. Packed with a variety of components, including buzzing motors, clicking gears, and warm candle lights, it's ready for you to unleash your creativity and assemble amazing models. Why Maker's Beginner Kit? Beginner-friendly: Carefully curated models, continuously updated, and easy-to-follow...

Overview The Marble Run Components Kit contains all the necessary hardware components for assembling a Marble Run. To complete the assembly for an entirely functional piece, users also need to...

Overview The Marble Run Components Kit contains all the necessary hardware components for assembling a Marble Run. To complete the assembly for an entirely functional piece, users also need to download the model files and 3D print the remaining parts.To download the model files and obtain detailed information, please visit the Marble Run on MakerWorld. Installation In the Box 1. Motor * 12. Marble * 10 (5 Colors) Notes 1. Please power the device using a USB power supply with the specified...

Overview MC board is the abbreviation of the machine controller board. It is the control center for the XYZ-axis motors, the cooling fans, the heat bed, and the AMS. Installation Learn more about...

Overview MC board is the abbreviation of the machine controller board. It is the control center for the XYZ-axis motors, the cooling fans, the heat bed, and the AMS. Installation Learn more about the replacement of the MC Board for X1 Series on Bambu Lab Wiki.

Overview The cable connects the MC board to the AP board on the P1 series printers. It supplies power and data. Installation Learn more about the replacement of the MC to AP cable for P1 Series on...

Overview The cable connects the MC board to the AP board on the P1 series printers. It supplies power and data. Installation Learn more about the replacement of the MC to AP cable for P1 Series on Bambu Lab Wiki. In the Box - MC to AP cable*1 Compatibility P1 Series Exclusive ...

Bambu Lab Micro Lidar (Dual Red Laser) The Bambu Micro Lidar (Dual Red Laser) is a sensor capable of measuring depth in micrometers. Using this unit, the system can measure the distance, calibrate...

Bambu Lab Micro Lidar (Dual Red Laser) The Bambu Micro Lidar (Dual Red Laser) is a sensor capable of measuring depth in micrometers. Using this unit, the system can measure the distance, calibrate the flow extruded from the nozzle, and scan the first layer. Installation Learn more about the replacement of the Bambu Micro Lidar (Dual Red Laser) - X1 Series on Bambu Lab Wiki. In the Box - Bambu Micro Lidar (Dual Red Laser) - X1 Series *1 Compatibility X1 Series Exclusive ...

The P1S Heatsink for MC Board serves the purpose of dissipating heat generated by the MC board. The P1S heatsink is horizontal oriented to work with the control board fan for heat dissipation.It is...

The P1S Heatsink for MC Board serves the purpose of dissipating heat generated by the MC board. The P1S heatsink is horizontal oriented to work with the control board fan for heat dissipation.It is also compatible with the P1P 3D Printer and can be used as an upgrade part, if you wish to enclose the printer and add an MC Board fan.Learn more about replacing the P1S Heatsink for MC Board on Bambu Lab Wiki. ...

The Part Cooling Fan is used to ensure adequate cooling of the printed layers during the printing process. It helps in rapidly cooling the material as it is extruded, allowing each layer to solidify...

The Part Cooling Fan is used to ensure adequate cooling of the printed layers during the printing process. It helps in rapidly cooling the material as it is extruded, allowing each layer to solidify and maintain its shape before the next layer is deposited. Compatible for A1 Series Learn more about replacing the Part Cooling Fan on Bambu Lab Wiki. ...

Overview This kit includes a variety of essential components, and to complete the assembly, you'll need to download the model files and 3D print the remaining parts. To download the model files and...

Overview This kit includes a variety of essential components, and to complete the assembly, you'll need to download the model files and 3D print the remaining parts. To download the model files and obtain detailed information, please visit the Piano Music Box Bottom Winding Kit-K014 and Piano Music Box Hand Winding Kit K015 on Makerworld. Compatible Models Creators Model Links Piano Music Box Bottom Winding Kit-K014 @sheepme Piano Music Box Bottom Winding Kit-K014 Piano Music Box Hand Winding...

Overview This kit includes a variety of essential components, and to complete the assembly, you'll need to download the model files and 3D print the remaining parts. To download the model files and...

Overview This kit includes a variety of essential components, and to complete the assembly, you'll need to download the model files and 3D print the remaining parts. To download the model files and obtain detailed information, please visit the Piano Music Box Bottom Winding Kit-K014 and Piano Music Box Hand Winding Kit K015 on Makerworld. Compatible Models Creators Model Links Piano Music Box Bottom Winding Kit-K014 @sheepme Piano Music Box Bottom Winding Kit-K014 Piano Music Box Hand Winding...

Overview The Cooling Fan for Hotend is used to cool and reduce the temperature of the ceramic heater. Installation Learn more about the replacement of cooling fan for hotend for X1E on Bambu Lab...

Overview The Cooling Fan for Hotend is used to cool and reduce the temperature of the ceramic heater. Installation Learn more about the replacement of cooling fan for hotend for X1E on Bambu Lab Wiki. In the Box - Cooling Fan for Hotend - X1E Compatibility X1E Exclusive ...

Overview The Print Head Front Cover is designed to protect the front part of the print head. It features a circular window that allows observation of the rotating status of the extruder gear....

Overview The Print Head Front Cover is designed to protect the front part of the print head. It features a circular window that allows observation of the rotating status of the extruder gear. Installation Learn more about replacing the Print Head Front Cover on Bambu Lab Wiki. In the Box 1. Print Head Front Cover * 1 Compatibility A1 Series ...

Bambu Lab Printer Cable Pack (4-in-1) The Bambu Lab Printer Cable Pack (4-in-1) is an essential 3D printer spare part designed to optimize connectivity and ensure consistent, reliable performance....

Bambu Lab Printer Cable Pack (4-in-1) The Bambu Lab Printer Cable Pack (4-in-1) is an essential 3D printer spare part designed to optimize connectivity and ensure consistent, reliable performance. Perfect for minimizing downtime and maximizing efficiency, this cable pack is ideal for keeping your 3D printer in peak condition. Designed to be compatible with: X1X1C

OverviewThe front door mounting kit is an accessory package for installing the glass front door of X1 and P1 series printersCompatibilityX1 Series and P1SIn the Box:Front door upper hinge *1Front...

OverviewThe front door mounting kit is an accessory package for installing the glass front door of X1 and P1 series printersCompatibilityX1 Series and P1SIn the Box:Front door upper hinge *1Front door lower hinge *1Silicone strip for door frame *1Door Frame magnet *2Front door upper hinge screws *2Lower front door hinge screws *2Installation:Learn more about the replacement of the front door mounting kiton Bambu Lab Wiki. ...

Overview PTFE Coupler is the anchor on the rear of the printer for fixing the PTFE tube. Installation Learn more about the replacement of the PTFE Coupler for P1 Series on Bambu Lab Wiki. In the...

Overview PTFE Coupler is the anchor on the rear of the printer for fixing the PTFE tube. Installation Learn more about the replacement of the PTFE Coupler for P1 Series on Bambu Lab Wiki. In the Box - PTFE Coupler*1 Compatibility P1 Series Exclusive ...

The function of PTFE is to reduce resistance and guide filament. The tube’s inner diameter is 2.5mm, and its outer diameter is 4mm. Please note that the PTFE tubes are consumables and are at risk of...

The function of PTFE is to reduce resistance and guide filament. The tube’s inner diameter is 2.5mm, and its outer diameter is 4mm. Please note that the PTFE tubes are consumables and are at risk of wear, as they may rub against the filament over time. We recommend that you check the PTFE tubes for wear during your maintenance of the machine.

Overview The function of PTFE Tube is to reduce resistance and guide filament. The tube’s inner diameter is 2.5mm, and its outer diameter is 4mm. Please note that the PTFE tubes are consumables and...

Overview The function of PTFE Tube is to reduce resistance and guide filament. The tube’s inner diameter is 2.5mm, and its outer diameter is 4mm. Please note that the PTFE tubes are consumables and are at risk of wear, as they may rub against the filament over time. We recommend that you check the PTFE tubes for wear during your maintenance of the machine. If the tubes are worn and not replaced in time, this may lead to feeding failures, filament accumulation inside the AMS, etc. In the...

Bambu Lab PTFE Tube compatible with A1 The function of PTFE is to reduce resistance and guide filament. The tube’s inner diameter is 2.5mm, and its outer diameter is 4mm. Please note that the PTFE...

Bambu Lab PTFE Tube compatible with A1 The function of PTFE is to reduce resistance and guide filament. The tube’s inner diameter is 2.5mm, and its outer diameter is 4mm. Please note that the PTFE tubes are consumables and are at risk of wear, as they may rub against the filament over time. We recommend that you check the PTFE tubes for wear during your maintenance of the machine.

Overview The function of PTFE is to reduce resistance and guide filament. The tube’s inner diameter is 2.5mm, and its outer diameter is 4mm. Compatibility P1P Exclusive In the box PTFE Tube (4pcs ):...

Overview The function of PTFE is to reduce resistance and guide filament. The tube’s inner diameter is 2.5mm, and its outer diameter is 4mm. Compatibility P1P Exclusive In the box PTFE Tube (4pcs ): 530mm*2 , 30mm*2

Overview The function of PTFE Tube is to reduce resistance and guide filament. The tube’s inner diameter is 2.5mm, and its outer diameter is 4mm. Please note that the PTFE tubes are consumables and...

Overview The function of PTFE Tube is to reduce resistance and guide filament. The tube’s inner diameter is 2.5mm, and its outer diameter is 4mm. Please note that the PTFE tubes are consumables and are at risk of wear, as they may rub against the filament over time. We recommend that you check the PTFE tubes for wear during your maintenance of the machine. If the tubes are worn and not replaced in time, this may lead to feeding failures, filament accumulation inside the AMS, etc. In the...

Bambu Lab PTFE Tube from AMS 2 Pro to H2 Series Printer The PTFE Tube from AMS 2 Pro to H2 Series Printer connects the AMS to the buffer. It facilitates the transfer of filament from the AMS to the...

Bambu Lab PTFE Tube from AMS 2 Pro to H2 Series Printer The PTFE Tube from AMS 2 Pro to H2 Series Printer connects the AMS to the buffer. It facilitates the transfer of filament from the AMS to the buffer, allowing for automated filament feeding into the printer. Compatibility H2 Series

Overview An assembly that installed on the back of the printer and it is used to clean the nozzle and slide the excess filament out of the printer. Installation Learn more about the replacement of...

Overview An assembly that installed on the back of the printer and it is used to clean the nozzle and slide the excess filament out of the printer. Installation Learn more about the replacement of the Purge Chute on Bambu Lab Wiki. In the Box - Purge Chute*1 Compatibility P1 Series and X1 Series ...

This Purge Wiper is designed to efficiently remove waste filament generated by the printer's hotend. It gathers and dislodges waste filament during different stages, including printer setup, pause...

This Purge Wiper is designed to efficiently remove waste filament generated by the printer's hotend. It gathers and dislodges waste filament during different stages, including printer setup, pause and resume operations, and filament changes for multi-color printing. Its purpose is to ensure the proper management and disposal of waste materials for seamless printing processes.Compatible with A1 Series.Learn more about the replacement of the Purge Wiper for A1 mini on Bambu Lab Wiki. ...

Overview The Filament Cutter is a blade that is used to cut the filament during a filament change. Installation Learn more about Replacement Filament Cutter on Bambu Lab Wiki. ...

Overview The Filament Cutter is a blade that is used to cut the filament during a filament change. Installation Learn more about Replacement Filament Cutter on Bambu Lab Wiki.

Overview The filament can be cut to prevent the supplies from clogging. When used with AMS, it assists with multi-material switching. Compatibility X1 Series, P1 Series, A1 Series Installation Learn...

Overview The filament can be cut to prevent the supplies from clogging. When used with AMS, it assists with multi-material switching. Compatibility X1 Series, P1 Series, A1 Series Installation Learn more about the replacement of the filament cutter on Bambu Lab Wiki: X1 Series and P1 Series, A1 Series. ...

Screws Information Item Number Item Name QTY Location1M2x2.5 FHCS (Machine Screw)10 ×Coil and the Heat Sink of A1 Main Board2M2.5x5 FHCS (Machine Screw)10 ×A1 mini Heatbed3BT2x5 SHCS (Self Tapping...

Screws Information Item Number Item Name QTY Location1M2x2.5 FHCS (Machine Screw)10 ×Coil and the Heat Sink of A1 Main Board2M2.5x5 FHCS (Machine Screw)10 ×A1 mini Heatbed3BT2x5 SHCS (Self Tapping Screw)20 ×Feeder unit and the Filament Sensor4BT2.6x5 SHCS (Self Tapping Screw)10 ×Filament Sensor Base5BT2.3x7 SHCS (Self Tapping Screw)20 ×Extruder Unit and its front cover6BT2x8 SHCS (Self Tapping Screw)10 ×Filament Pressing Block7BT2.6x14 SHCS (Self Tapping Screw)5 ×Cutter Lever8Stainless...

Overview:The Silicone Sock for Hotend is made from high-quality silicone for higher temperature resistance (rated to 300°C printing temperatures).Ensuring optimal thermal insulation and tear...

Overview:The Silicone Sock for Hotend is made from high-quality silicone for higher temperature resistance (rated to 300°C printing temperatures).Ensuring optimal thermal insulation and tear resistance, the silicone sock also provides the nozzle with long-lasting protection from cooling air and plastic adhesion.Installation: During the installation process, please make sure the silicone sock fits exactly into place before printing.Learn more about silicone sock replacement here:...

Bambu Lab Silicone Sock for Hotend - P2S The hotend silicone sleeve is a silicone component installed over the hotend nozzle, designed to maintain stable nozzle temperature. Compatibility P2 Series ...

Bambu Lab Silicone Sock for Hotend - P2S The hotend silicone sleeve is a silicone component installed over the hotend nozzle, designed to maintain stable nozzle temperature. Compatibility P2 Series

Multi-Stage Filtration: Filter Out 99% of Particles Down to 0.3µm & VOCs Equipped with G4 and F8 filters to capture dust and larger particles, a high-performance Carbon Filter (1200mg/g...

Multi-Stage Filtration: Filter Out 99% of Particles Down to 0.3µm & VOCs Equipped with G4 and F8 filters to capture dust and larger particles, a high-performance Carbon Filter (1200mg/g adsorption power) to remove VOCs, and a HEPA H13 filter to trap ultra-fine particles as small as 0.3µm, the Bambu Smoke Purifier ensures efficient air purification. It effectively eliminates chemicals and unpleasant odors through a layered filtration system, creating a healthier, stress-free creative...

Recommended Settings Please note that other slicer settings might need to be adjusted based on the printed model and the filament requirements High Z-axis precision printing The use of a Smooth PEI...

Recommended Settings Please note that other slicer settings might need to be adjusted based on the printed model and the filament requirements High Z-axis precision printing The use of a Smooth PEI Plate contributes to improved Z-axis precision during the printing process, ensuring greater accuracy and consistency in the vertical dimension. These qualities make the Smooth PEI Plate an excellent choice for printing parts that demand a high level of fit accuracy, where precise alignment and...

Recommended Settings Please note that other slicer settings might need to be adjusted based on the printed model and the filament requirements High Z-axis precision printing The use of a Smooth PEI...

Recommended Settings Please note that other slicer settings might need to be adjusted based on the printed model and the filament requirements High Z-axis precision printing The use of a Smooth PEI Plate contributes to improved Z-axis precision during the printing process, ensuring greater accuracy and consistency in the vertical dimension. These qualities make the Smooth PEI Plate an excellent choice for printing parts that demand a high level of fit accuracy, where precise alignment and...

High Z-axis Precision Printing Theuse of a Smooth PEI Plate contributes to improved Z-axis precision during the printing process, ensuring greater accuracy and consistency in the vertical dimension....

High Z-axis Precision Printing Theuse of a Smooth PEI Plate contributes to improved Z-axis precision during the printing process, ensuring greater accuracy and consistency in the vertical dimension. These qualities make the Smooth PEI Plate an excellent choice for printing parts that demand a high level of fit accuracy, where precise alignment and tight tolerances are crucial. Smooth and Matte Surface Finish The use of a specially selected matte PEI sheet can impart a smooth and matte texture...

Bambu Lab StrongGrip Cutting Mat Designed for heavy materials like leather and thick cardstock. Its strong adhesive ensures secure holding during cutting. Installation Learn more about the...

Bambu Lab StrongGrip Cutting Mat Designed for heavy materials like leather and thick cardstock. Its strong adhesive ensures secure holding during cutting. Installation Learn more about the StrongGrip Cutting Mat on Bambu Lab Wiki. Compatibility H2D Laser ...

High Z-axis Precision Printing Theuse of a Smooth PEI Plate contributes to improved Z-axis precision during the printing process, ensuring greater accuracy and consistency in the vertical dimension....

High Z-axis Precision Printing Theuse of a Smooth PEI Plate contributes to improved Z-axis precision during the printing process, ensuring greater accuracy and consistency in the vertical dimension. These qualities make the Smooth PEI Plate an excellent choice for printing parts that demand a high level of fit accuracy, where precise alignment and tight tolerances are crucial. Smooth and Matte Surface Finish The use of a specially selected matte PEI sheet can impart a smooth and matte texture...

High Z-axis Precision Printing Theuse of a Smooth PEI Plate contributes to improved Z-axis precision during the printing process, ensuring greater accuracy and consistency in the vertical dimension....

High Z-axis Precision Printing Theuse of a Smooth PEI Plate contributes to improved Z-axis precision during the printing process, ensuring greater accuracy and consistency in the vertical dimension. These qualities make the Smooth PEI Plate an excellent choice for printing parts that demand a high level of fit accuracy, where precise alignment and tight tolerances are crucial. Smooth and Matte Surface Finish The use of a specially selected matte PEI sheet can impart a smooth and matte texture...

High Z-axis Precision Printing Theuse of a Smooth PEI Plate contributes to improved Z-axis precision during the printing process, ensuring greater accuracy and consistency in the vertical dimension....

High Z-axis Precision Printing Theuse of a Smooth PEI Plate contributes to improved Z-axis precision during the printing process, ensuring greater accuracy and consistency in the vertical dimension. These qualities make the Smooth PEI Plate an excellent choice for printing parts that demand a high level of fit accuracy, where precise alignment and tight tolerances are crucial. Smooth and Matte Surface Finish The use of a specially selected matte PEI sheet can impart a smooth and matte texture...

Overview The Toolhead Board is the main circuit board of the toolhead which provides connectivity to the toolhead parts, including the hotend heating assembly, extruder unit, hotend cooling fan,...

Overview The Toolhead Board is the main circuit board of the toolhead which provides connectivity to the toolhead parts, including the hotend heating assembly, extruder unit, hotend cooling fan, filament sensor, etc. Installation Learn more about replacing the Toolhead Board on Bambu Lab Wiki. In the Box 1. Toolhead Board * 12. M2-2 Screws * 4 Compatibility A1 mini ...

OverviewThe rear cover of the printer's toolhead.InstallationLearn more about the replacement of the Toolhead Rear Housing on Bambu Lab Wiki.In the Box:- Toolhead Rear Housing*1Compatibility:X1...

OverviewThe rear cover of the printer's toolhead.InstallationLearn more about the replacement of the Toolhead Rear Housing on Bambu Lab Wiki.In the Box:- Toolhead Rear Housing*1Compatibility:X1 Series and P1 Series

Overview 3.5-inch IPS capacitive touchscreen which connects to the Mainboard which is used to control the printer through the touchscreen interface. Compatibility A1 Exclusive In the Box Touch...

Overview 3.5-inch IPS capacitive touchscreen which connects to the Mainboard which is used to control the printer through the touchscreen interface. Compatibility A1 Exclusive In the Box Touch Screen - A1 *1 Installation Learn more about replacing the A1 Touch Screen on Bambu Lab Wiki. ...

Overview 2.4-inch IPS capacitive touchscreen which connects to the Mainboard. Users can control the printer through the touch screen interface. Compatibility A1 mini Installation Learn more about...

Overview 2.4-inch IPS capacitive touchscreen which connects to the Mainboard. Users can control the printer through the touch screen interface. Compatibility A1 mini Installation Learn more about the installation process of the Touch Screen for A1 mini on Bambu Lab Wiki.Product Specification ...

Overview The Triple-axis Tourbillon Model Components Kit contains all the necessary hardware components for assembling a Triple-axis Tourbillon Model. To complete the assembly for an entirely...

Overview The Triple-axis Tourbillon Model Components Kit contains all the necessary hardware components for assembling a Triple-axis Tourbillon Model. To complete the assembly for an entirely functional piece, users also need to download the model files and 3D print the remaining parts.Creator Program: The Creator Program is a collaborative program between Bambu Lab and creators. Creators unleash their creativity to design 3D printing models, while Bambu Lab provides compatible hardware kits...

Bambu Lab Tungsten Carbide Nozzle - High Flow - 0.4 mm - H2/P2S HRA 90 Tougher nozzle, lower maintenance With HRA 90 compared to hardened steel's 74, the Tungsten Carbide nozzle provides exceptional...

Bambu Lab Tungsten Carbide Nozzle - High Flow - 0.4 mm - H2/P2S HRA 90 Tougher nozzle, lower maintenance With HRA 90 compared to hardened steel's 74, the Tungsten Carbide nozzle provides exceptional wear resistance. This results in a 50% increase in lifespan when printing abrasive, high-performance fiber-reinforced filaments. Quick Swap Nozzle Design The special design of hotend heating assembly enables easy separation of the thermal and electronic components of the hotend. Simply unlock the...

Bambu Lab Tungsten Carbide Nozzle - Standard Flow - 0.4 mm - H2/P2S HRA 90 Tougher nozzle, lower maintenance With HRA 90 compared to hardened steel's 74, the Tungsten Carbide nozzle provides...

Bambu Lab Tungsten Carbide Nozzle - Standard Flow - 0.4 mm - H2/P2S HRA 90 Tougher nozzle, lower maintenance With HRA 90 compared to hardened steel's 74, the Tungsten Carbide nozzle provides exceptional wear resistance. This results in a 50% increase in lifespan when printing abrasive, high-performance fiber-reinforced filaments. Quick Swap Nozzle Design The special design of hotend heating assembly enables easy separation of the thermal and electronic components of the hotend. Simply unlock...

Overview Facilitates the connection between the Mainboard and the TH Extrusion Board for MC-TH power and serial communication. Compatibility A1 Exclusive In the Box Bambu USB-C Cable...

Overview Facilitates the connection between the Mainboard and the TH Extrusion Board for MC-TH power and serial communication. Compatibility A1 Exclusive In the Box Bambu USB-C Cable *1 Installation Learn more about the replacement of the A1 Bambu USB-C Cable on Bambu Lab Wiki. ...

Overview Facilitates the connection between the Mainboard and the TH Extrusion board for MC-TH power supply and serial communication. Compatibility A1 mini In the Box Bambu USB-C Cable...

Overview Facilitates the connection between the Mainboard and the TH Extrusion board for MC-TH power supply and serial communication. Compatibility A1 mini In the Box Bambu USB-C Cable *1 Installation Learn more about the replacement of the A1 mini Bambu USB-C Cable on on Bambu Lab Wiki. ...

Bambu Lab Vision Encoder – Accuracy To A New Level Take your 3D printing accuracy to the next level with the Bambu Lab Vision Encoder. This advanced calibration tool enhances motion accuracy to...

Bambu Lab Vision Encoder – Accuracy To A New Level Take your 3D printing accuracy to the next level with the Bambu Lab Vision Encoder. This advanced calibration tool enhances motion accuracy to below 50μm, compensating for natural mechanical variances and long-term wear across machines. This calibration is distance-independent, ensuring consistent accuracy regardless of model size, with its impact becoming even more pronounced in larger prints. Paired with exclusive Bambu Studio features like...

Overview The Wireless Charger Kit contains all the non-3D printed parts for assembling an entirely functional A1 mini Wireless Charger or an Air Force Command Headquarters Wireless Charger. To...

Overview The Wireless Charger Kit contains all the non-3D printed parts for assembling an entirely functional A1 mini Wireless Charger or an Air Force Command Headquarters Wireless Charger. To complete the work, you need to download the model files and 3D print the parts.To download the model files and obtained detailed information, please visit A1 mini Wireless Charger or Air Force Command Headquarters on Makerworld. Compatible ModelsCreatorsModel LinksA1 mini Wireless ChargerBambu LabA1 mini...

Overview The Wireless Mouse Components Kit contains all the necessary hardware components for assembling a Wireless Mouse. To complete the assembly for an entirely functional piece, users also need...

Overview The Wireless Mouse Components Kit contains all the necessary hardware components for assembling a Wireless Mouse. To complete the assembly for an entirely functional piece, users also need to download the model files and 3D print the remaining parts. Compatible ModelsCreatorsModel LinksThe Mouse - Bambu Lab Mouse Kit CompatibleJorge RuiThe Mouse - Bambu Lab Mouse Kit Compatible"Manta" mouse - Bambu Lab Mouse kit CompatibleJorge Rui"Manta" mouse - Bambu Lab Mouse kit CompatibleWireless...

Overview The Y Belt is a crucial transmission component within the Y-axis assembly, facilitating the connection between the Y motor and the heatbed, enabling smooth movement along the Y-direction....

Overview The Y Belt is a crucial transmission component within the Y-axis assembly, facilitating the connection between the Y motor and the heatbed, enabling smooth movement along the Y-direction. It is imperative to replace the Y Belt promptly in cases of severe wear or breakage to avoid disrupting printer operations. Compatibility A1 mini In the Box Y Belt *1 BT3-08 *3 M3-12 *2 Installation Learn more about the replacement of the Y belt for A1 mini on Bambu Lab Wiki. ...

The X Belt is a crucial transmission component within the X-Axis assembly, facilitating the connection between the X motor and the tool head, enabling smooth movement along the X-axis. It is...

The X Belt is a crucial transmission component within the X-Axis assembly, facilitating the connection between the X motor and the tool head, enabling smooth movement along the X-axis. It is imperative to replace the X belt promptly in cases of severe wear or breakage to avoid operational disruptions of the printer.Learn more about replacing the X Belt - A1 on Bambu Lab Wiki. ...

The X-Axis Assembly ensures that the X-axis movement of the toolhead remains consistently fixed on the horizontal plane. The X-axis utilizes linear rail guidance, which provides stability, smooth...

The X-Axis Assembly ensures that the X-axis movement of the toolhead remains consistently fixed on the horizontal plane. The X-axis utilizes linear rail guidance, which provides stability, smooth motion, improved guiding precision, and longevity. Installation Learn more about replacing the X-Axis Assembly on Bambu Lab Wiki. ...

Overview The ceramic heater can heat the nozzle up to 300℃, which is for use with Bambu Lab complete hotend assemby only. *Please confirm your printer model before making a purchase, as the...

Overview The ceramic heater can heat the nozzle up to 300℃, which is for use with Bambu Lab complete hotend assemby only. *Please confirm your printer model before making a purchase, as the connector may differ between the X1 Series version and the P1P version. Installation Learn more about the replacement of ceramic heater on Bambu Lab Wiki. In the Box - Ceramic Heater * 3- Thermal Grease * 3- Retaining Clip * 3 Compatibility X1 Series Exclusive ...

Overview The ceramic heater can heat the nozzle up to 300℃, which is for use with Bambu Lab complete hotend assembly only. *Please confirm your printer model before making a purchase, this is for...

Overview The ceramic heater can heat the nozzle up to 300℃, which is for use with Bambu Lab complete hotend assembly only. *Please confirm your printer model before making a purchase, this is for the X1E. Installation Learn more about the replacement of ceramic heater on Bambu Lab Wiki. In the Box - Ceramic Heater - Thermal Grease - Retaining Clip Compatibility XE1 Exclusive ...

Overview The idler pulley installed on the left side of the X-axis is used to change the direction of movement of the X belt. Installation Learn more about the replacement of the X/Y-Axis pulley -...

Overview The idler pulley installed on the left side of the X-axis is used to change the direction of movement of the X belt. Installation Learn more about the replacement of the X/Y-Axis pulley - A1 mini on Bambu Lab Wiki. In the Box -X/Y-Axis Pulley - A1 mini *1 Compatibility A1 mini Exclusive ...

The Y Belt is a crucial transmission component within the Y-axis assembly, facilitating the connection between the Y motor and the heatbed, enabling smooth movement along the Y-direction. It is...

The Y Belt is a crucial transmission component within the Y-axis assembly, facilitating the connection between the Y motor and the heatbed, enabling smooth movement along the Y-direction. It is imperative to replace the Y-Axis Belt promptly in cases of severe wear or breakage to avoid disrupting printer operations.Learn more about replacing the Y Belt - A1 on Bambu Lab Wiki. ...

Overview A component for tensioning the Y-axis belt of the A1 mini. Installation Learn more about the replacement of the Y-Axis Tensioner - A1 mini on Bambu Lab Wiki. In the Box -Y-Axis Tensioner -...

Overview A component for tensioning the Y-axis belt of the A1 mini. Installation Learn more about the replacement of the Y-Axis Tensioner - A1 mini on Bambu Lab Wiki. In the Box -Y-Axis Tensioner - A1 mini *1 Compatibility A1 mini Exclusive ...

Overview The function of the Z belt is to transmit the motion of the Z motor to the three Z-axis lead screws. Compatibility X1 Series, P1P ...

Overview The function of the Z belt is to transmit the motion of the Z motor to the three Z-axis lead screws. Compatibility X1 Series, P1P

The Z-axis Coupler is used to connect the Z-axis motor and the Z-axis lead screw. It enables precise transmission of motion and torque while accommodating certain levels of radial, axial, and...

The Z-axis Coupler is used to connect the Z-axis motor and the Z-axis lead screw. It enables precise transmission of motion and torque while accommodating certain levels of radial, axial, and angular misalignment. Installation Learn more about the replacement of the Z-Axis Coupler for A1 mini on Bambu Lab Wiki. ...

The Z-Axis Top Cover is designed to protect the top of the Z-axis assembly.Learn more about replacing the Z-Axis Top Cover on Bambu Lab Wiki. ...

The Z-Axis Top Cover is designed to protect the top of the Z-axis assembly.Learn more about replacing the Z-Axis Top Cover on Bambu Lab Wiki.

Overview: Prolonging the lifetime of the build plate is to use a sharp scraper for releasing the model from the printing surface. After the plate has cooled down, gently slide the scraper underneath...

Overview: Prolonging the lifetime of the build plate is to use a sharp scraper for releasing the model from the printing surface. After the plate has cooled down, gently slide the scraper underneath one of the corners of the model then carefully bend the sheet to remove the model. Compatibility: X1 Series, P1P How to print your Scraper grip? Bambu Lab 3D printer comes with scraper models. Print 'Scraper grip' from the built-in files! In the Box: 3x Bambu scraper, 1x PE bag ...

Recommended Settings Please note that other slicer settings might need to be adjusted based on the printed model and the filament requirements Excellent first-layer adhesion, Improved durability...

Recommended Settings Please note that other slicer settings might need to be adjusted based on the printed model and the filament requirements Excellent first-layer adhesion, Improved durability After optimizing the manufacturing process of the Bambu Texture PEI Plate, the durability of the plate is enhanced. Additionally, the adhesion between the prints and the plate is significantly improved, eliminating the need for adhesives.*In some situations, glue is required for very specific filaments...

Recommended Settings Please note that other slicer settings might need to be adjusted based on the printed model and the filament requirements Excellent first-layer adhesion, Improved durability...

Recommended Settings Please note that other slicer settings might need to be adjusted based on the printed model and the filament requirements Excellent first-layer adhesion, Improved durability After optimizing the manufacturing process of the Bambu Texture PEI Plate, the durability of the plate is enhanced. Additionally, the adhesion between the prints and the plate is significantly improved, eliminating the need for adhesives.*In some situations, glue is required for very specific...

Overview The Bambu Lab USB-C cable is installed in the towing chain and is only suitable for Bambu Lab X1 series printers. Compatibility X1 Series Exclusive ...

Overview The Bambu Lab USB-C cable is installed in the towing chain and is only suitable for Bambu Lab X1 series printers. Compatibility X1 Series Exclusive

Overview With the cable chain assembled, the trajectory of the toolhead cable and feeding tube can be safely confined to the horizontal plane during printing. It can also protect the toolhead cable...

Overview With the cable chain assembled, the trajectory of the toolhead cable and feeding tube can be safely confined to the horizontal plane during printing. It can also protect the toolhead cable and feeding tube from being damaged during repetitive bending as a result of motion. * If you want to assemble a cable chain to enclose your P1P 3D printer, please replace the original toolhead cable with the heavy duty toolhead cable for a reliable performance. Otherwise, the cable chain may have a...

Overview The chamber camera is included by default in the X1-Carbon and is an optional upgrade that you can install for the X1. The chamber camera has three functions, which are Remote Livestreams,...

Overview The chamber camera is included by default in the X1-Carbon and is an optional upgrade that you can install for the X1. The chamber camera has three functions, which are Remote Livestreams, Spaghetti Detection and Time-lapses respectively. Remote livestream: you can observe print progress anytime, anywhere.Spaghetti Detection: Spaghetti detection uses AI to detect print failures. If this feature is enabled, once spaghetti is detected, the printer pauses and waits for your input before...

Overview The Chamber Temperature Regulator Fan is used to control the chamber temperature and to help filter the air inside the chassis. It can be manually controlled on the screen or the slicer....

Overview The Chamber Temperature Regulator Fan is used to control the chamber temperature and to help filter the air inside the chassis. It can be manually controlled on the screen or the slicer. Installation For X1 Series: Bambu Lab Wiki For P1P (Enclosure): Bambu Lab Wiki In the Box 1. Chamber Temperature Regulator Fan Compatibility X1 Series, P1 Series Product SpecificationsVoltage / Operation Voltage24 V / 15 V~27 VMaterialsPlastic, Metal, RubberRated Speed4800 rpm/minPackaging...

Overview The control board fan is used to cool the control board to prevent the control board from overheating and shutting down. Installation Learn more about the replacement of control board fan...

Overview The control board fan is used to cool the control board to prevent the control board from overheating and shutting down. Installation Learn more about the replacement of control board fan for X1 Series on Bambu Lab Wiki. In the Box - Control Board Fan Compatibility X1 Series ...

Overview The Electric Coffee WDT Tool Kit contains all the non-3D printed parts for assembling an entirely functional Electric Coffee WDT Tool. To complete the work, you need to download the model...

Overview The Electric Coffee WDT Tool Kit contains all the non-3D printed parts for assembling an entirely functional Electric Coffee WDT Tool. To complete the work, you need to download the model files and 3D print the parts.To download the model files and obtain detailed information, please visit the BooKoo Coffee Electric WDT on Makerworld. Creator Program: The Creator Program is a collaborative program between Bambu Lab and creators. Creators unleash their creativity to design 3D printing...

Learn more about the replacement of the Extruder Motor for X1 series and P1 Series on Bambu Lab Wiki. In the Box - Extruder Motor*1 - Glue*1 Compatibility X1 Series and P1 Series ...

Learn more about the replacement of the Extruder Motor for X1 series and P1 Series on Bambu Lab Wiki. In the Box - Extruder Motor*1 - Glue*1 Compatibility X1 Series and P1 Series

Overview The Extruder Unit features dual gears made of hardened steel to feed filament into the hotend. The hardened steel gears provide increased extrusion force, prevent slippage, and enhance...

Overview The Extruder Unit features dual gears made of hardened steel to feed filament into the hotend. The hardened steel gears provide increased extrusion force, prevent slippage, and enhance abrasion resistance. These gears enable the extruder unit to handle tough engineering filaments such as carbon fiber nylon and glass fiber nylon.The extruder unit is also equipped with a filament cutter for filament unloading or switching, and an extruder motor that supplies the required power for the...

Overview The front cover of the P1S printer is a black-gray cover that is installed on the front of the printer and printed with P1S. Installation Learn more about the replacement of the Front Cover...

Overview The front cover of the P1S printer is a black-gray cover that is installed on the front of the printer and printed with P1S. Installation Learn more about the replacement of the Front Cover for P1S on Bambu Lab Wiki. In the Box - Front Cover*1 - ST3-4 screw*2 - BT3-5 screw*1 - Glue*1 Compatibility P1 Series Exclusive ...

Overview The hardened steel extruder unit is equipped with double gears made of hardened steel, which provides increased extrusion force, prevents slippage, and enhances abrasion resistance. These...

Overview The hardened steel extruder unit is equipped with double gears made of hardened steel, which provides increased extrusion force, prevents slippage, and enhances abrasion resistance. These gears enable the extruder unit to handle tough engineering filaments such as carbon fiber nylon and glass fiber nylon. In addition, the extruder unit includes a sensor that supports filament break detection, which can help prevent print failures and improve overall printing efficiency. *Please...

Overview The hardened steel extruder unit is equipped with double gears made of hardened steel, which provides increased extrusion force, prevents slippage, and enhances abrasion resistance. These...

Overview The hardened steel extruder unit is equipped with double gears made of hardened steel, which provides increased extrusion force, prevents slippage, and enhances abrasion resistance. These gears enable the extruder unit to handle tough engineering filaments such as carbon fiber nylon and glass fiber nylon. In addition, the extruder unit includes a sensor that supports filament break detection, which can help prevent print failures and improve overall printing efficiency. *Please...

Connects the A1 mini hotbed to the Mainboard, which is used to power the hotbed and provide feedback on the temperature of the hotbed.InstallationLearn more about the replacement of the Heatbed...

Connects the A1 mini hotbed to the Mainboard, which is used to power the hotbed and provide feedback on the temperature of the hotbed.InstallationLearn more about the replacement of the Heatbed Cable for A1 mini on Bambu Lab Wiki .

Overview A small circuit board installed underneath the heatbed, which connects the heatbed sensors to the MC board. Installation Learn more about the replacement of the Heatbed Piezo Interface...

Overview A small circuit board installed underneath the heatbed, which connects the heatbed sensors to the MC board. Installation Learn more about the replacement of the Heatbed Piezo Interface Board for P1 Series and X1 Series on Bambu Lab Wiki. In the Box - Heatbed Piezo Interface Board*1 - ST2-3 screw*1 Compatibility X1 Series and P1 Series ...