All Items
In Stock

Products 1-7 of 7
Show

Micro Gearmotor - Enclosure

Back Order
Availability: Back Order
Item #: ROB-12105 -
Price: $3.04
Sparkfun

These enclosures allow you to mount your micro gearmotor to other Actobotics products easily. Once your gearmotor is inserted, you can take advantage of the 0.77” hole pattern. These enclosures have...

These enclosures allow you to mount your micro gearmotor to other Actobotics products easily. Once your gearmotor is inserted, you can take advantage of the 0.77” hole pattern. These enclosures have a length of 1.14”, a width of 1”, and a thickness of 0.50”. Actobotics is a robotics building system based around extruded aluminum channels, gears, precision shafts, and ball bearings. Thanks to the two standardized hole patterns, nearly all Actobotics components can be intuitively connected...

MIKROE H-Bridge 7 Click

Out of Stock
Availability: Out of Stock
Item #: ROB-18787 -
Price: $106.20
Sparkfun

MIKROE H-Bridge 7 Click features flexible motor driver IC for a wide variety of applications, labeled as the DRV8876N. This Click board™ integrates an N-channel H-bridge, charge pump regulator, and...

MIKROE H-Bridge 7 Click features flexible motor driver IC for a wide variety of applications, labeled as the DRV8876N. This Click board™ integrates an N-channel H-bridge, charge pump regulator, and protection circuitry. The charge pump improves efficiency by allowing for both high-side and low-side N-channels MOSFETs and 100% duty cycle support. This IC allows the H-Bridge 7 Click to achieve ultra-low quiescent current draw by shutting down most of the internal circuitry with his low-power...

MIKROE H-Bridge 8 Click

Out of Stock
Availability: Out of Stock
Item #: ROB-19144 -
Price: $36.97
Sparkfun

MIKROE H-Bridge 8 Click is a compact add-on board that contains H-bridge current regulator. This board features the MP6519, a monolithic, step-down, current-source driver for applications that...

MIKROE H-Bridge 8 Click is a compact add-on board that contains H-bridge current regulator. This board features the MP6519, a monolithic, step-down, current-source driver for applications that require accurate and fast current-response control from Monolithic Power Systems (MPS). It achieves excellent load and line regulation over a wide input supply range up to 28V. The four integrated MOSFET H-bridge control provide a fast dynamic load response and an ultra-high efficiency solution. Complete...

MIKROE H-Bridge 9 Click

Out of Stock
Availability: Out of Stock
Item #: ROB-19134 -
Price: $88.89
Sparkfun

MIKROE H-Bridge 9 Click is a compact add-on board that contains six MOSFET half-bridge outputs. This board features the L99UDL01, a six-channel half-bridge driver monolithic integrated circuit that...

MIKROE H-Bridge 9 Click is a compact add-on board that contains six MOSFET half-bridge outputs. This board features the L99UDL01, a six-channel half-bridge driver monolithic integrated circuit that is PWM configurable and current regulated from STMicroelectronics. It achieves excellent load and line regulation over a wide input supply range up to 18V. These six integrated MOSFET H-bridges are commanded entirely by the SPI interface using duration and current level commands. Complete protection...

Servo Extension Cable - Female to Male (Shrouded)

Back Order
Availability: Back Order
Item #: ROB-15808 -
Price: $5.71
Sparkfun

This is a 12 inch servo extension cable that comes in handy when your servo is further away from the controller than the wire on the servo allows. The male connector on one end goes to controller,...

This is a 12 inch servo extension cable that comes in handy when your servo is further away from the controller than the wire on the servo allows. The male connector on one end goes to controller, while the female connector mates with servo. Fits all Hitec, Futaba, JR, Multiplex, and Airtronics Z servos. Wire can also be used as a simple 0.1" jumper cable. Documents: Datasheet ...

Wheel Encoder Kit

Back Order
Availability: Back Order
Item #: ROB-12629 -
Price: $26.53
Sparkfun

This is the Wheel Encoder Kit from DAGU, a simple add-on to any wheeled robot that can help measure the speed or distance the chassis travels. Each wheel encoder kit consists of two neodymium 8-pole...

This is the Wheel Encoder Kit from DAGU, a simple add-on to any wheeled robot that can help measure the speed or distance the chassis travels. Each wheel encoder kit consists of two neodymium 8-pole magnets with rubber hubs and two hall-effect sensors terminated with 150mm cables and 3-pin female servo headers. These wheel encoders require a supply voltage of 3-24V with a supply current of 4mA. Features: Supply Voltage: 3-24V Supply Current: 4mA per sensor Output Voltage: 26V Max Output...

ZIF to Terminal Block for BLDC

Out of Stock
Availability: Out of Stock
Item #: PRT-19514 -
Price: $14.71
Sparkfun

ZIF to Terminal Block for BLDC represents a small-sized adapter board that allows you to connect all BLDC motors without a Hall sensor and a flexprint port to target Brushless Click board™. The...

ZIF to Terminal Block for BLDC represents a small-sized adapter board that allows you to connect all BLDC motors without a Hall sensor and a flexprint port to target Brushless Click board™. The adapter consists of one ZIF connector ZIF1004UH with four pins of 1.0mm pitch, and two 2.54mm pitch screw terminals on opposite sides of the board. Connect the screw terminals to target Brushless Click board with appropriate COM, U, V, and W pinout, and then connect 4-pole flexprint connector with all...