Skip to main content
Your Saved For Later list is empty.
My Favorites

SparkFun Parts and Devices

Shop a wide selection of genuine SparkFun parts, breakout boards, sensors, and development tools for your electronics and STEM projects.
Products 217-280 of 280
Show
SparkFun Qwiic Shield for Teensy
Price: $8.19 inc GST
$8.19 inc GST
Sparkfun

    The SparkFun Qwiic Shield for Teensy provides you with a quick and easy way to enter into SparkFun's Qwiic ecosystem with your Teensy boards. This shield is sized to work with the footprint of...

    The SparkFun Qwiic Shield for Teensy provides you with a quick and easy way to enter into SparkFun's Qwiic ecosystem with your Teensy boards. This shield is sized to work with the footprint of Teensy 4.0, Teensy 3.2, and Teensy LC. This shield connects the I2C bus (GND, 3.3V, SDA, and SCL) on your Teensy to four SparkFun Qwiic connectors (two horizontally and two vertically mounted). The Qwiic ecosystem allows for easy daisy chaining so, as long as your devices are on different addresses, you...

    Limited Stock
    SparkFun Qwiic Shield for Teensy - Extended
    Price: $10.21 inc GST
    $10.21 inc GST
    Sparkfun

      The SparkFun Extended Qwiic Shield for Teensy provides you with a quick and easy way to enter into SparkFun's Qwiic ecosystem with your Teensy boards. This shield is sized to work with the footprint...

      The SparkFun Extended Qwiic Shield for Teensy provides you with a quick and easy way to enter into SparkFun's Qwiic ecosystem with your Teensy boards. This shield is sized to work with the footprint of Teensy 4.1, Teensy 3.6, and Teensy 3.5. This shield connects the I2C bus (GND, 3.3V, SDA, and SCL) on your Teensy to four SparkFun Qwiic connectors (two horizontally and two vertically mounted). The Qwiic ecosystem allows for easy daisy chaining so, as long as your devices are on different...

      Limited Stock
      SparkFun QwiicBus - EndPoint
      Price: $23.17 inc GST
      $23.17 inc GST
      Sparkfun

        The SparkFun QwiicBus EndPoint is the fastest and easiest way to extend the range of your I2C communication bus. The breakout uses NXP’s PCA9615 IC, which converts the two default I2C signals into...

        The SparkFun QwiicBus EndPoint is the fastest and easiest way to extend the range of your I2C communication bus. The breakout uses NXP’s PCA9615 IC, which converts the two default I2C signals into four differential signals, two for SCL and two for SDA. The differential signals are sent over an Ethernet cable, which attaches to the breakout through the on-board RJ-45 connectors. The differential signaling allows the I2C signals to reach distances of up to 100ft. while still maintaining their...

        Limited Stock
        SparkFun RedBot Basic Kit
        Price: $147.73 inc GST
        $147.73 inc GST
        Sparkfun

          "Welcome the RedBot Basic Kit, a robotic development platform capable of teaching two motor robotics and sensor integration! This kit comes with our RedBot Mainboard, the Shadow Chassis, a handful...

          "Welcome the RedBot Basic Kit, a robotic development platform capable of teaching two motor robotics and sensor integration! This kit comes with our RedBot Mainboard, the Shadow Chassis, a handful of sensors, and everything required to get it moving. The RedBot Mainboard is a modular robotic development platform that works with the Arduino IDE. The RedBot is a motor driver and Ardiuno combination with various headers and connections, eliminating the need to stack multiple shields to get...

          Limited Stock
          SparkFun RedBot Sensor - Mechanical Bumper
          Price: $10.74 inc GST
          $10.74 inc GST
          Sparkfun

            These simple switches are the Mechanical Bumper sensor for the SparkFun RedBot, giving you the ability to detect a collision before it really happens. This sensor works by acting as a SPST switch....

            These simple switches are the Mechanical Bumper sensor for the SparkFun RedBot, giving you the ability to detect a collision before it really happens. This sensor works by acting as a SPST switch. When the "whisker" bumps into a foreign object it will make contact with a nut next to it, closing the connection and, by default, turning off the motor. By attaching these mechanical bumpers to you robot the whisker will bump something before your robot crashes into it. The sensor has a 3-pin header...

            Limited Stock
            SparkFun RFID Starter Kit
            Price: $100.39 inc GST
            $100.39 inc GST
            Sparkfun

              This it the SparkFun RFID Starter Kit, an all-in-one kit that offer everything you need to get your next RFID project off the ground. This kit includes our USB RFID Reader, ID-12LA RFID module, and...

              This it the SparkFun RFID Starter Kit, an all-in-one kit that offer everything you need to get your next RFID project off the ground. This kit includes our USB RFID Reader, ID-12LA RFID module, and two 125kHz RFID cards. We've done away with the annoying clamshell and now offer this in the same type of box as the rest of our kits. The RFID USB Reader is a simple to use, USB to serial base unit for the ID-3LA, ID-12LA, and ID-20LA readers. Simply plug a reader into the headers and attach a...

              Limited Stock
              SparkFun RGB and Gesture Sensor - APDS-9960
              Price: $26.50 inc GST
              $26.50 inc GST
              Sparkfun

                This is the SparkFun RGB and Gesture Sensor, a small breakout board with a built in APDS-9960 sensor that offers ambient light and color measuring, proximity detection, and touchless gesture...

                This is the SparkFun RGB and Gesture Sensor, a small breakout board with a built in APDS-9960 sensor that offers ambient light and color measuring, proximity detection, and touchless gesture sensing. With this RGB and Gesture Sensor you will be able to control a computer, microcontroller, robot, and more with a simple swipe of your hand! This is, in fact, the same sensor that the Samsung Galaxy S5 uses and is probably one of the best gesture sensors on the market for the price. The APDS-9960...

                Limited Stock
                SparkFun RS232 Shifter - SMD
                Price: $28.27 inc GST
                $28.27 inc GST
                Sparkfun

                  The smallest and easiest to use serial conversion circuit on the market! This board has one purpose in life - to convert RS232 to TTL and vice versa (TX and RX). This will allow a microcontroller to...

                  The smallest and easiest to use serial conversion circuit on the market! This board has one purpose in life - to convert RS232 to TTL and vice versa (TX and RX). This will allow a microcontroller to communicate with a computer. Shifter SMD is powered from the target application and can run at any voltage! That's right - power the board at 5V and the unit will convert RS232 to 5V TTL. Power the board at 2.8V and the Shifter board will convert RS232 to 2.8V CMOS TTL. Includes two indicator LEDs...

                  Limited Stock
                  SparkFun SOIC to DIP Adapter - 20-Pin
                  Price: $7.13 inc GST
                  $7.13 inc GST
                  Sparkfun

                    This is a low-cost, basic SOIC breakout boards. This custom PCB will interface a standard SOIC package IC to 0.1" headers, which are easier to work with and integrate well with breadboards. There is...

                    This is a low-cost, basic SOIC breakout boards. This custom PCB will interface a standard SOIC package IC to 0.1" headers, which are easier to work with and integrate well with breadboards. There is DIP-standard 0.6" spacing between the two rows of pins. 40 Pin break-away headers are perfect for use with these custom PCBs. Machine pin headers may be a better option for IC sockets. Features: 0.7x1.1" Documents: Schematic Eagle Files GitHub (Design Files) ...

                    Limited Stock
                    SparkFun Soil Moisture Sensor
                    Price: $10.72 inc GST
                    $10.72 inc GST
                    Sparkfun

                      The SparkFun Soil Moisture Sensor is a simple breakout for measuring the moisture in soil and similar materials. The soil moisture sensor is pretty straight forward to use. The two large exposed...

                      The SparkFun Soil Moisture Sensor is a simple breakout for measuring the moisture in soil and similar materials. The soil moisture sensor is pretty straight forward to use. The two large exposed pads function as probes for the sensor, together acting as a variable resistor. The more water that is in the soil means the better the conductivity between the pads will be and will result in a lower resistance, and a higher SIG out. To get the SparkFun Soil Moisture Sensor functioning all you will...

                      Limited Stock
                      SparkFun Solder-able Breadboard - Large
                      Price: $18.08 inc GST
                      $18.08 inc GST
                      Sparkfun

                        This is the Large SparkFun Solder-able Breadboard. A bare PCB that is the exact size as our full-size breadboard with the same connections to pins and power rails. This board is especially useful...

                        This is the Large SparkFun Solder-able Breadboard. A bare PCB that is the exact size as our full-size breadboard with the same connections to pins and power rails. This board is especially useful for preserving a prototype or experiment you just created on a solderless breadboard by soldering all the pieces in place. The large solder-able breadboard also includes real estate for screw terminal connectors and a trace down the center gutter for ground. Documents: Schematic Eagle Files Hookup...

                        Limited Stock
                        SparkFun Sound Detector
                        Price: $19.77 inc GST
                        $19.77 inc GST
                        Sparkfun

                          The SparkFun Sound Detector is a small and very easy to use audio sensing board with three different outputs. The Sound Detector not only provides an audio output, but also a binary indication of...

                          The SparkFun Sound Detector is a small and very easy to use audio sensing board with three different outputs. The Sound Detector not only provides an audio output, but also a binary indication of the presence of sound, and an analog representation of its amplitude. The 3 outputs are simultaneous and independent, so you can use as many or as few as you want at once. The envelope output allows you to easily read amplitude of sound by simply measuring the analog voltage. Gain can be adjusted with...

                          Limited Stock
                          SparkFun SSOP to DIP Adapter - 28-Pin
                          Price: $6.56 inc GST
                          $6.56 inc GST
                          Sparkfun

                            8, 16, 20, and 28-Pin SSOP to DIP break out boards. The footprint was rotated to accommodate different width SSOP devices and can be used with any pin count up to 28 pins. Designed to be used with...

                            8, 16, 20, and 28-Pin SSOP to DIP break out boards. The footprint was rotated to accommodate different width SSOP devices and can be used with any pin count up to 28 pins. Designed to be used with 0.65mm pitch devices but can also be used with 0.025" pitch devices (comes out to ~0.635mm). We've made these 0.635mm devices fit just fine. Can be used with packages that have a lead span of .230" up to .350". 40 Pin break-away headers are perfect for use with these custom PCBs. Machine pin headers...

                            Limited Stock
                            SparkFun TeensyView
                            Price: $31.08 inc GST
                            $31.08 inc GST
                            Sparkfun

                              The SparkFun TeensyView brings you an easy way to add a small, white-on-black OLED to your Teensy development board. The 128x32 monochrome display is controlled with the popular SSD1306 IC, and is a...

                              The SparkFun TeensyView brings you an easy way to add a small, white-on-black OLED to your Teensy development board. The 128x32 monochrome display is controlled with the popular SSD1306 IC, and is a great way to display debug information and to visualize data without the need for a serial terminal. The board matches the Teensy 3 form factor perfectly, and was designed from the ground up to be as flexible as possible while still being able to nest down into a low-profile addition for the...

                              Limited Stock
                              SparkFun Thing Plus - RP2040
                              Price: $32.40 inc GST
                              $32.40 inc GST
                              Sparkfun

                                The SparkFun Thing Plus - RP2040 is a low-cost, high performance board with flexible digital interfaces featuring the Raspberry Pi Foundation's RP2040 microcontroller. Besides the Thing Plus or...

                                The SparkFun Thing Plus - RP2040 is a low-cost, high performance board with flexible digital interfaces featuring the Raspberry Pi Foundation's RP2040 microcontroller. Besides the Thing Plus or Feather footprint (with 18 GPIO pins), the board also includes an SD card slot, 16MB (128Mbit) flash memory, a JST single cell battery connector (with a charging circuit and fuel gauge sensor), an addressable WS2812 RGB LED, JTAG PTH pins, four (4-40 screw) mounting holes, and our signature Qwiic...

                                Limited Stock
                                SparkFun Third Hand Kit
                                Price: $73.89 inc GST
                                $73.89 inc GST
                                Sparkfun

                                  Are you frustrated with the lack of dexterity from most third hands? The SparkFun Third Hand gives you the ability to hold a board between two alligator clips on two flexible arms with multiple...

                                  Are you frustrated with the lack of dexterity from most third hands? The SparkFun Third Hand gives you the ability to hold a board between two alligator clips on two flexible arms with multiple points of articulation. The arm's wide range of articulation gives you access to any angle of the board that you are currently working on, making soldering that much easier. The SparkFun Third Hand also won't move around while you work thanks to a heavy aluminum base supporting the arms. Even though we...

                                  Limited Stock
                                  SparkFun ToF Range Finder Sensor - VL6180
                                  Price: $46.85 inc GST
                                  $46.85 inc GST
                                  Sparkfun

                                    This is the SparkFun "Time-of-Flight" Range Finder, a sensor board for the VL6180 distance sensor. Unlike most distance sensors that rely on reflected light intensity or reflected angles to...

                                    This is the SparkFun "Time-of-Flight" Range Finder, a sensor board for the VL6180 distance sensor. Unlike most distance sensors that rely on reflected light intensity or reflected angles to determine range, the VL6180 uses a precise clock to measure the time it takes light to bounce back from a surface. This affords the ToF Range Finder and VL6180 a great benefit over other methods because it can be much more accurate and more immune to noise. Does this technology sound familiar? Well it...

                                    Limited Stock
                                    SparkFun Transceiver Breakout - nRF24L01+
                                    Price: $37.82 inc GST
                                    $37.82 inc GST
                                    Sparkfun

                                      This module uses the newest 2.4GHz transceiver from Nordic Semiconductor, the nRF24L01+. This transceiver IC operates in the 2.4GHz band and has many new features! Take all the coolness of the...

                                      This module uses the newest 2.4GHz transceiver from Nordic Semiconductor, the nRF24L01+. This transceiver IC operates in the 2.4GHz band and has many new features! Take all the coolness of the nRF2401A and add some extra pipelines, buffers, and an auto-retransmit feature - very nice! Please note: We now populate these boards with the nRF24L01+. The '+' version of the IC has improved range, sensitivity, and data rates. The command set is backward compatible with the original nRF24L01. Features:...

                                      Limited Stock
                                      SparkFun Triple Axis Accelerometer Breakout - ADXL345
                                      Price: $38.78 inc GST
                                      $38.78 inc GST
                                      Sparkfun

                                        This new version adds 2 standoff holes as well as an extra decoupling capacitor. The ADXL345 is a small, thin, low power, 3-axis MEMS accelerometer with high resolution (13-bit) measurement at up to...

                                        This new version adds 2 standoff holes as well as an extra decoupling capacitor. The ADXL345 is a small, thin, low power, 3-axis MEMS accelerometer with high resolution (13-bit) measurement at up to +-16 g. Digital output data is formatted as 16-bit twos complement and is accessible through either a SPI (3- or 4-wire) or I2C digital interface. The ADXL345 is well suited to measures the static acceleration of gravity in tilt-sensing applications, as well as dynamic acceleration resulting from...

                                        Limited Stock
                                        SparkFun Triple Axis Accelerometer Breakout - ADXL362
                                        Price: $28.27 inc GST
                                        $28.27 inc GST
                                        Sparkfun

                                          We've been using and selling Analog Devices' ADXL accelerometers for a good while now, and now we've found another great part in the series! The ADXL362 is a complete 3-axis MEMS acceleration...

                                          We've been using and selling Analog Devices' ADXL accelerometers for a good while now, and now we've found another great part in the series! The ADXL362 is a complete 3-axis MEMS acceleration measurement system that operates at extremely low power consumption levels. It measures both dynamic acceleration, resulting from motion or shock, and static acceleration, such as tilt. It's easy to communicate with the ADXL362 over SPI and built-in digital logic even enables autonomous operation for...

                                          Limited Stock
                                          SparkFun Triple Axis Digital Accelerometer Breakout - ADXL313 (Qwiic)
                                          Price: $32.94 inc GST
                                          $32.94 inc GST
                                          Sparkfun

                                            The SparkFun ADXL313 Breakout is a low power, high resolution (up to 13-bits) 3-axis accelerometer for measurement up to ±4g. This breakout measures the static acceleration of gravity in...

                                            The SparkFun ADXL313 Breakout is a low power, high resolution (up to 13-bits) 3-axis accelerometer for measurement up to ±4g. This breakout measures the static acceleration of gravity in tilt-sensing applications, as well as dynamic acceleration resulting from motion or shock. Digital output data is formatted as 16-bit two's complement and is accessible through the on-board Qwiic connectors (I2C) or SPI. The ADXL313 Breakouts high resolution and low noise enable resolution of inclination...

                                            Limited Stock
                                            SparkFun Triple-Axis Digital-Output Gyro Breakout - ITG-3200
                                            Price: $43.39 inc GST
                                            $43.39 inc GST
                                            Sparkfun

                                              "This is a breakout board for InvenSense’s ITG-3200, a groundbreaking triple-axis, digital output MEMS gyroscope. The ITG-3200 features three 16-bit analog-to-digital converters (ADCs) for...

                                              "This is a breakout board for InvenSense’s ITG-3200, a groundbreaking triple-axis, digital output MEMS gyroscope. The ITG-3200 features three 16-bit analog-to-digital converters (ADCs) for digitizing the gyro outputs, a user-selectable internal low-pass filter bandwidth, and a Fast-Mode I2C (400kHz) interface. Additional features include an embedded temperature sensor and a 2% accurate internal oscillator. The ITG-3200 can be powered at anywhere between 2.1 and 3.6V. For power supply...

                                              Limited Stock
                                              SparkFun USB LiPoly Charger - Single Cell
                                              Price: $28.75 inc GST
                                              $28.75 inc GST
                                              Sparkfun

                                                If you need to charge LiPo batteries, this simple charger will do just that, and do it fast! The SparkFun USB LiPo Charger is a basic charging circuit that allows you to charge 3.7V LiPo cells at a...

                                                If you need to charge LiPo batteries, this simple charger will do just that, and do it fast! The SparkFun USB LiPo Charger is a basic charging circuit that allows you to charge 3.7V LiPo cells at a rate of 500mA or 100mA. It is designed to charge single-cell Li-Ion or Li-Polymer batteries. The board incorporates a charging circuit, status LED, selectable solder jumper for 500mA or 100mA charging current, external LED footprint, USB input, two pre-installed JST connectors for SYS OUT and BATT...

                                                Limited Stock
                                                SparkFun USB MicroB Plug Breakout
                                                Price: $7.50 inc GST
                                                $7.50 inc GST
                                                Sparkfun

                                                  We have no idea what USB device you are hooking up to, but if you want to access the microUSB port on something, you might want this. We broke out all 5 pins with a vertical microUSB connector for...

                                                  We have no idea what USB device you are hooking up to, but if you want to access the microUSB port on something, you might want this. We broke out all 5 pins with a vertical microUSB connector for your prototyping needs. Features: Dimensions: 23.54L x 14.75W x 14.65H mm Documents: Schematic Eagle Files GitHub ...

                                                  Limited Stock
                                                  SparkFun USB Mini-B Breakout
                                                  Price: $4.52 inc GST
                                                  $4.52 inc GST
                                                  Sparkfun

                                                    This new version now has all 5 pins broken out on the connector. We have no idea what USB device you are hooking up to, but if you need to add a miniUSB/USB Mini-B connector to your breadboard -...

                                                    This new version now has all 5 pins broken out on the connector. We have no idea what USB device you are hooking up to, but if you need to add a miniUSB/USB Mini-B connector to your breadboard - here it is. Also good for an un-regulated, non-limited 5V supply up to 100mA. Documents: [Eagle Files](http://cdn.sparkfun.com/datasheets/BreakoutBoards/miniUSB Breakout v13.zip) GitHub ...

                                                    Limited Stock
                                                    SparkFun USB Mini-B Cable - 6 Foot
                                                    Price: $6.95 inc GST
                                                    $6.95 inc GST
                                                    Sparkfun

                                                      This is a USB 2.0 type A to Mini-B 5-pin cable. You know, the mini-B connector that usually comes with USB Hubs, Cameras, MP3 players, etc. You can use this with our LiPo Charger, FTDI Basic...

                                                      This is a USB 2.0 type A to Mini-B 5-pin cable. You know, the mini-B connector that usually comes with USB Hubs, Cameras, MP3 players, etc. You can use this with our LiPo Charger, FTDI Basic Programmer or even combine it with the CP210x IC and SMD Mini-B connector to create your own portable USB device! The best part? It's SparkFun Red and has the flame logo embossed on the connector shroud. Sweet. If you're still trying to wrap your head around the world of USB cables, why not check out our...

                                                      Limited Stock
                                                      SparkFun USB to Serial Breakout - FT232RL
                                                      Price: $33.06 inc GST
                                                      $33.06 inc GST
                                                      Sparkfun

                                                        This is the SparkFun USB to Serial Breakout for the FT232RL, a small board with a built in USB to serial UART interface. This little breakout is built around the FT232RL IC from FTDI, with an...

                                                        This is the SparkFun USB to Serial Breakout for the FT232RL, a small board with a built in USB to serial UART interface. This little breakout is built around the FT232RL IC from FTDI, with an internal oscillator, EEPROM, and a 28-pin SSOP package this is a serious little chip. With this version, we've corrected a few issues found with the board. These changes include fixes to the VCCIO, a change from the mini USB to micro USB connector, and a few footprint modifications. Other than finding...

                                                        Limited Stock
                                                        SparkFun USB Type A Female Breakout
                                                        Price: $8.38 inc GST
                                                        $8.38 inc GST
                                                        Sparkfun

                                                          This simple board breaks out a female USB type A connector's VCC, GND, D- and D+ pins to a 0.1" pitch header. If you want to add a USB to your project, but don't want to put up with soldering...

                                                          This simple board breaks out a female USB type A connector's VCC, GND, D- and D+ pins to a 0.1" pitch header. If you want to add a USB to your project, but don't want to put up with soldering tiny connectors, this is the board for you. Dimensions: 1.02 x 0.9" (26.06 x 22.93mm) Documents: Schematic Eagle Files Hookup Guide GitHub ...

                                                          Limited Stock
                                                          SparkFun Voltage-Level Translator Breakout - TXB0104
                                                          Price: $9.74 inc GST
                                                          $9.74 inc GST
                                                          Sparkfun

                                                            This is a breakout board for the Texas Instruments TXB0104 module. The TXB0104 is a 4-bit bidirectional voltage-level translator with automatic direction sensing. This 4-bit noninverting translator...

                                                            This is a breakout board for the Texas Instruments TXB0104 module. The TXB0104 is a 4-bit bidirectional voltage-level translator with automatic direction sensing. This 4-bit noninverting translator uses two separate configurable power-supply rails. The A port is designed to track VCCA. VCCA accepts any supply voltage from 1.2V to 3.6V. The B port is designed to track VCCB. VCCB accepts any supply voltage from 1.65V to 5.5V. This allows for universal low-voltage bidirectional translation...

                                                            Limited Stock
                                                            Hot!
                                                            SparkFun Weather Shield
                                                            Price: $46.52 inc GST
                                                            Was $79.89 inc GST
                                                            Sparkfun

                                                              "The Weather Shield is an easy to use Arduino shield that grants you access to barometric pressure, relative humidity, luminosity and temperature. There are also connections on this shield to...

                                                              "The Weather Shield is an easy to use Arduino shield that grants you access to barometric pressure, relative humidity, luminosity and temperature. There are also connections on this shield to optional sensors such as wind speed, direction, rain gauge and GPS for location and super accurate timing. These Weather Shields utilize the HTU21D humidity, MPL3115A2 barometric pressure, and ALS-PT19 light sensors and relies on the HTU21D and MPL3115A2 Arduino libraries. Each shield comes with two...

                                                              Limited Stock
                                                              SparkFun XBee Explorer Regulated
                                                              Price: $21.71 inc GST
                                                              $21.71 inc GST
                                                              Sparkfun

                                                                The SparkFun XBee Explorer Regulated takes care of the 3.3V regulation, signal conditioning, and basic activity indicators (Power, RSSI and DIN/DOUT activity LEDs). It translates the 5V serial...

                                                                The SparkFun XBee Explorer Regulated takes care of the 3.3V regulation, signal conditioning, and basic activity indicators (Power, RSSI and DIN/DOUT activity LEDs). It translates the 5V serial signals to 3.3V so that you can connect a 5V (down to 3.3V) system to any XBee module. The board was conveniently designed to mate directly with the SparkFun Arduino Pro series of boards for wireless bootloading and USB based configuration. This unit works with all XBee modules including the Series 1 and...

                                                                Limited Stock
                                                                SparkFun XBee Explorer USB
                                                                Price: $42.63 inc GST
                                                                $42.63 inc GST
                                                                Sparkfun

                                                                  This is a simple to use, USB to serial base unit for the Digi XBee line. This unit works with all XBee modules including the Series 1 and Series 2.5, standard and Pro version. Plug the unit into the...

                                                                  This is a simple to use, USB to serial base unit for the Digi XBee line. This unit works with all XBee modules including the Series 1 and Series 2.5, standard and Pro version. Plug the unit into the XBee Explorer, attach a mini USB cable, and you will have direct access to the serial and programming pins on the XBee unit. The highlight of this board is an FT231X USB-to-Serial converter. That’s what translates data between your computer and the XBee. There’s also a reset button, and a voltage...

                                                                  Limited Stock
                                                                  Speaker - 0.5W (8 Ohm)
                                                                  Price: $4.52 inc GST
                                                                  $4.52 inc GST
                                                                  Sparkfun

                                                                    A small audio speaker that is ideal for radio and amplifier projects and is small enough to fit in robot projects. Features: Small Size Power rating: 0.5W Impedance: 8Ω 50mm diameter, 16mm high,...

                                                                    A small audio speaker that is ideal for radio and amplifier projects and is small enough to fit in robot projects. Features: Small Size Power rating: 0.5W Impedance: 8Ω 50mm diameter, 16mm high, 28mm base diameter

                                                                    Limited Stock
                                                                    Hot!
                                                                    SPI Shortcut
                                                                    Price: $32.05 inc GST
                                                                    Was $34.45 inc GST
                                                                    Sparkfun

                                                                      SPI Shortcut Description: The SPI Shortcut allows you to control SPI pins over USB, allowing for a virtual "SPI Terminal." Using basic serial commands you can access any SPI device such as sensors,...

                                                                      SPI Shortcut Description: The SPI Shortcut allows you to control SPI pins over USB, allowing for a virtual "SPI Terminal." Using basic serial commands you can access any SPI device such as sensors, media, and even program some devices. You can change all of the SPI features (frequency, data order, etc.) on the fly with no programming involved! Comes with a simple-to-use terminal interface. All you need is the FTDI USB driver and a basic terminal program. Documents: User's Manual Schematic FTDI...

                                                                      Limited Stock
                                                                      Stackable Header - 3 Pin (Female, 0.1")
                                                                      Price: $0.91 inc GST
                                                                      $0.91 inc GST
                                                                      Sparkfun

                                                                        This is a simple 3 pin female PTH header. This header is in a configuration that makes it ideal to be used with the MyoWare Muscle Sensor line. Each pin has a spacing of 0.1" in between each...

                                                                        This is a simple 3 pin female PTH header. This header is in a configuration that makes it ideal to be used with the MyoWare Muscle Sensor line. Each pin has a spacing of 0.1" in between each other. Documents: Datasheet

                                                                        Limited Stock
                                                                        Standoff - Metal (4-40; 3/8"; 10 pack)
                                                                        Price: $5.32 inc GST
                                                                        $5.32 inc GST
                                                                        Sparkfun

                                                                          Metal short standoffs: 3/8" long x 1/4"OD. Used to get your proto board up off the table. #4-40 thread. Fits all development boards with available holes. Don't forget the screws! Related below. Set...

                                                                          Metal short standoffs: 3/8" long x 1/4"OD. Used to get your proto board up off the table. #4-40 thread. Fits all development boards with available holes. Don't forget the screws! Related below. Set of ten

                                                                          Limited Stock
                                                                          Standoffs Plastic - (4-40; 3/4"; 10 pack)
                                                                          Price: $7.12 inc GST
                                                                          $7.12 inc GST
                                                                          Sparkfun

                                                                            These nylon standoffs are 3/4" long and tapped for a 4-40 screw. These are great for mounting your board in an enclosure, or just getting it up off the table. Sold in packs of 10. Check below for...

                                                                            These nylon standoffs are 3/4" long and tapped for a 4-40 screw. These are great for mounting your board in an enclosure, or just getting it up off the table. Sold in packs of 10. Check below for matching screws.

                                                                            Limited Stock
                                                                            Step Up/Down Inverting Switching Regulator
                                                                            Price: $3.39 inc GST
                                                                            $3.39 inc GST
                                                                            Sparkfun

                                                                              "DC to DC converter/regulator MC34063A. Has an input range of 3V to 40V, output switch current of up to 1.5 amp. Step up, step down and invert capability. This is the unit we used in the high...

                                                                              "DC to DC converter/regulator MC34063A. Has an input range of 3V to 40V, output switch current of up to 1.5 amp. Step up, step down and invert capability. This is the unit we used in the high voltage ringer circuit for the port-o-rotary phone! Documents:MC34063 Datasheet" ...

                                                                              Limited Stock
                                                                              Stepper Motor with Cable
                                                                              Price: $30.43 inc GST
                                                                              $30.43 inc GST
                                                                              Sparkfun

                                                                                This is a simple, but very powerful stepper motor with a 4-wire cable attached. This is a Bipolar Motor. Features: Step Angle (degrees) :1.8 2 Phase Rated Voltage : 12V Rated Current : 0.33A Holding...

                                                                                This is a simple, but very powerful stepper motor with a 4-wire cable attached. This is a Bipolar Motor. Features: Step Angle (degrees) :1.8 2 Phase Rated Voltage : 12V Rated Current : 0.33A Holding Torque : 2.3kg*cm 5mm Diameter Drive Shaft Winding resistance: 32.6 Ω Winding inductance: 48 mH Max flux linkage: 1.8 Vs Maximum Detent Torque: 0.016 N.M Total inertia (kg.m.m): 3.5 Kg.m.m Total friction (kg.m/s): 4 Kg.m/s NEMA 17 Mounting Hole Pattern (31mm) Motor Width: 42mm (1.67”) Documents:...

                                                                                Limited Stock
                                                                                STK500 Compatible USB Programmer
                                                                                Price: $88.02 inc GST
                                                                                $88.02 inc GST
                                                                                Sparkfun

                                                                                  AVR-ISP500 is a fast and reliable USB AVR programmer, and works directly with AVR Studio. It is recognized as a STK500 programmer and programs all AVRs. It emulates USB CDC so no drivers are...

                                                                                  AVR-ISP500 is a fast and reliable USB AVR programmer, and works directly with AVR Studio. It is recognized as a STK500 programmer and programs all AVRs. It emulates USB CDC so no drivers are required and works under Windows, Linux and MacOS. If you do not want to use AVRStudio you can use AVR-ISP500 with AVRdude. Features: USB Powered Connects to PC via USB 2.0 Full speed Uses Atmel's 2x5 pin ICSP and 2x3 connector layout 45x30 mm (1.7x1.2") + 20 cm (8") cable Documents: User Manual AVR ICSP...

                                                                                  Limited Stock
                                                                                  Sylvias Super Awesome Kit
                                                                                  Price: $52.08 inc GST
                                                                                  $52.08 inc GST
                                                                                  Sparkfun

                                                                                    "This is Sylvia’s Super Awesome Kit, a companion kit for Sylvia’s Super-Awesome Project Book: Super Simple Arduino! With this kit you will be able to follow along with the book and create three...

                                                                                    "This is Sylvia’s Super Awesome Kit, a companion kit for Sylvia’s Super-Awesome Project Book: Super Simple Arduino! With this kit you will be able to follow along with the book and create three great projects to get started on an Arduino adventure! A lot of work has gone into the Super-Awesome Project Book, and we wanted to make it as easy as possible to get the three projects in this book started. The book, written by Super-Awesome Sylvia, star of Super-Awesome Sylvia’s Super-Awesome Maker...

                                                                                    Limited Stock
                                                                                    Teensy Arduino Shield Adapter
                                                                                    Price: $26.81 inc GST
                                                                                    $26.81 inc GST
                                                                                    Sparkfun

                                                                                      The Teensy is an amazing and compact development platform in a breadboard friendly form factor, but what if you could incorporate it into the Arduino architecture? The Teensy Arduino Shield Adapter...

                                                                                      The Teensy is an amazing and compact development platform in a breadboard friendly form factor, but what if you could incorporate it into the Arduino architecture? The Teensy Arduino Shield Adapter allows you to attach your Teensy and utilize your favorite Arduino shields without the requirement of a breadboard or any complicated wiring. Needless to say, the Teensy Arduino Shield Adapter is a useful tool for upgrading all of your existing Arduino projects to a more powerful controller! As we...

                                                                                      Limited Stock
                                                                                      Teensy Header Kit
                                                                                      Price: $2.71 inc GST
                                                                                      $2.71 inc GST
                                                                                      Sparkfun

                                                                                        These headers are made to work with the Teensy 4.0, Teensy 3.2, and Teensy LC development boards. Each kit of headers makes your Teensy breadboard compatible and will allow for stacking a Teensy and...

                                                                                        These headers are made to work with the Teensy 4.0, Teensy 3.2, and Teensy LC development boards. Each kit of headers makes your Teensy breadboard compatible and will allow for stacking a Teensy and Teensy-compatible shield board. This kit includes five headers (two 13-pin, one 7-pin, one 3-pin, and one 2x7 right-angle SMT), enough to connect your chosen Teensy in any configuration you need! Note: This Header Kit can also be used for the Teensy 3.0 and 3.1, as the pin layout has not changed...

                                                                                        Limited Stock
                                                                                        Thermocouple Type-K - Glass Braid Insulated (Bare Wire)
                                                                                        Price: $25.43 inc GST
                                                                                        $25.43 inc GST
                                                                                        Sparkfun

                                                                                          36" high temperature Type-K Thermocouple with glass braid insulation. Features: Type-K Thermocouple (Ni-Cr) 30 gauge stripped and prepped wires Thermocouple range : -270 to +1372C (-454 to...

                                                                                          36" high temperature Type-K Thermocouple with glass braid insulation. Features: Type-K Thermocouple (Ni-Cr) 30 gauge stripped and prepped wires Thermocouple range : -270 to +1372C (-454 to +2501F) Glass braid insulation range : -73 to +482C(-100 to +900F) Yellow + / Red - Works great with our Thermocouple Amplifier AD595 IC!

                                                                                          Limited Stock
                                                                                          Hot!
                                                                                          Tilt-a-Whirl Breakout - RPI-1031
                                                                                          Price: $7.48 inc GST
                                                                                          Was $8.04 inc GST
                                                                                          Sparkfun

                                                                                            Tilt-a-Whirl Breakout - RPI-1031 Description: The RPI-1031 tilt sensor is capable of sensing a change in orientation in four different directions: forward, back, left or right. This breakout board...

                                                                                            Tilt-a-Whirl Breakout - RPI-1031 Description: The RPI-1031 tilt sensor is capable of sensing a change in orientation in four different directions: forward, back, left or right. This breakout board makes it easier to incorporate the RPI-1031 in your next project by breaking the necessary pins out to standard 0.1" spaced headers. This board will work at either 3.3 or 5V. Documents: Schematic Eagle Files Datasheet (RPI-1031) Product Page(RPI-1031) Hookup Guide bildr Tutorial Product Video GitHub...

                                                                                            Limited Stock
                                                                                            Hot!
                                                                                            Transceiver nRF2401A Module Trace Antenna
                                                                                            Price: $25.65 inc GST
                                                                                            Was $27.56 inc GST
                                                                                            Sparkfun

                                                                                              Transceiver nRF2401A Module Trace AntennaDescription: Miniature RF (MiRF) 2.4GHz transceiver modules with built in antenna designed around the Nordic Semiconductor nRF2401A with high sensitivity and...

                                                                                              Transceiver nRF2401A Module Trace AntennaDescription: Miniature RF (MiRF) 2.4GHz transceiver modules with built in antenna designed around the Nordic Semiconductor nRF2401A with high sensitivity and good range. These units are a SparkFun exclusive; small in stature, big on performance, all wrapped up in a user friendly package. Units come with an empty 0.1" spaced footprint ready for a straight header, right angle header (recommended), or your own wires/umbilical cable.The following pins are...

                                                                                              Limited Stock
                                                                                              Tweezers - Curved (cross-lock, ESD Safe)
                                                                                              Price: $7.13 inc GST
                                                                                              $7.13 inc GST
                                                                                              Sparkfun

                                                                                                These are nice, cross-locking, curved tweezers, unlike traditional models the tips on these tweezers will remain closed until squeezed open. They have a nice, rounded tip which allows you to pick up...

                                                                                                These are nice, cross-locking, curved tweezers, unlike traditional models the tips on these tweezers will remain closed until squeezed open. They have a nice, rounded tip which allows you to pick up very small parts with precision. This is a great tool to have if you're working with surface mount components or anything with very small parts. The ESD-safe coating will also help prevent electro-static damage to sensitive electronic components. Documents: Product Video ...

                                                                                                Limited Stock
                                                                                                Uh-oh Battery Level Indicator Kit
                                                                                                Price: $10.35 inc GST
                                                                                                $10.35 inc GST
                                                                                                Sparkfun

                                                                                                  Uh-oh Battery Level Indicator Kit Description: Under-powering a digital device can sometimes have pretty nasty consequences. Brown-out conditions can cause memory to get written or overwritten in...

                                                                                                  Uh-oh Battery Level Indicator Kit Description: Under-powering a digital device can sometimes have pretty nasty consequences. Brown-out conditions can cause memory to get written or overwritten in odd ways, can cause unexpected behavior in connected systems and just generally screw up your day. One way to avoid this is to keep an eye on your battery voltage and turn off the system before it gets too low (or plug it in). We've whipped up a little board to help you out with this situation: the...

                                                                                                  Limited Stock
                                                                                                  Ultrasonic Range Finder - HRLV-MaxSonar-EZ1
                                                                                                  Price: $63.11 inc GST
                                                                                                  $63.11 inc GST
                                                                                                  Sparkfun

                                                                                                    These easy-to-use ultrasonic rangefinders from Maxbotix work the same way as the EZ line that you know and love, but this new high-resolution series features 1 millimeter resolution! As with the...

                                                                                                    These easy-to-use ultrasonic rangefinders from Maxbotix work the same way as the EZ line that you know and love, but this new high-resolution series features 1 millimeter resolution! As with the rest of the Maxbotix range finders, these sensors feature Analog Voltage, RS232 Serial, and Pulse Width outputs making them easy to interface with any microcontroller. These sensors have a maximum range of 5000 mm (195 inches) with virtually no dead zone (although objects closer than 30 cm will...

                                                                                                    Limited Stock
                                                                                                    Ultrasonic Range Finder - LV-MaxSonar-EZ0
                                                                                                    Price: $49.92 inc GST
                                                                                                    $49.92 inc GST
                                                                                                    Sparkfun

                                                                                                      This is the fantastically easy to use sensor from Maxbotix. We are extremely pleased with the size, quality, and ease of use of this little range finder. The serial interface is a bit odd (it's...

                                                                                                      This is the fantastically easy to use sensor from Maxbotix. We are extremely pleased with the size, quality, and ease of use of this little range finder. The serial interface is a bit odd (it's RS232 instead of standard TTL), but the PWM and Analog interfaces will allow any micro to listen easily enough. The sensor provides very accurate readings of 0 to 255 inches (0 to 6.45m) in 1 inch increments with little or no dead zone! Maxbotix is offering the EZ0, EZ1, EZ2, EZ3, and EZ4 with...

                                                                                                      Limited Stock
                                                                                                      Ultrasonic Range Finder - LV-MaxSonar-EZ1
                                                                                                      Price: $47.40 inc GST
                                                                                                      $47.40 inc GST
                                                                                                      Sparkfun

                                                                                                        This is the fantastically easy to use sensor from Maxbotix. We are extremely pleased with the size, quality, and ease of use of this little range finder. The serial interface is a bit odd (it's...

                                                                                                        This is the fantastically easy to use sensor from Maxbotix. We are extremely pleased with the size, quality, and ease of use of this little range finder. The serial interface is a bit odd (it's RS232 instead of standard TTL), but the PWM and Analog interfaces will allow any micro to listen easily enough. The sensor provides very accurate readings of 0 to 255 inches (0 to 6.45m) in 1 inch increments with little or no dead zone! Maxbotix is offering the EZ0, EZ1, EZ2, EZ3, and EZ4 with...

                                                                                                        Limited Stock
                                                                                                        Unigeek - Unicorn Soldering Badge Kit
                                                                                                        Price: $22.01 inc GST
                                                                                                        $22.01 inc GST
                                                                                                        Sparkfun

                                                                                                          Get a little magical with your soldering skills! The Unigeek is a beginners soldering kit that teaches you the basics of PTH and SMD soldering while assembling a light up unicorn badge with an color...

                                                                                                          Get a little magical with your soldering skills! The Unigeek is a beginners soldering kit that teaches you the basics of PTH and SMD soldering while assembling a light up unicorn badge with an color changing eye. Each Unigeek kit takes about 5-15min to assemble with basic soldering materials (not included), and yes, the PCB in this kit really is rainbow colored out of the bag! Every Unigeek Soldering Badge Kit includes one multicolored unicorn PCB, a CR2032 battery holder, a pin back, and an...

                                                                                                          Limited Stock
                                                                                                          Hot!
                                                                                                          USB Cable - A-to-B 6 Foot Retail
                                                                                                          Price: $5.58 inc GST
                                                                                                          Was $9.90 inc GST
                                                                                                          Sparkfun

                                                                                                            "This is a standard issue USB 2.0 cable. This is the most common A to B Male/Male type peripheral cable, the kind that’s usually used for printers. Compatible with most SFE designed USB boards as...

                                                                                                            "This is a standard issue USB 2.0 cable. This is the most common A to B Male/Male type peripheral cable, the kind that’s usually used for printers. Compatible with most SFE designed USB boards as well as USB Arduino boards like the Uno. Length: 6 Feet"

                                                                                                            Limited Stock
                                                                                                            USB Cable A to B - 6 Foot
                                                                                                            Price: $9.30 inc GST
                                                                                                            $9.30 inc GST
                                                                                                            Sparkfun

                                                                                                              This is a standard issue USB 2.0 cable. This is the most common A to B Male/Male type peripheral cable, the kind that's usually used for printers. Compatible with most SFE designed USB boards as...

                                                                                                              This is a standard issue USB 2.0 cable. This is the most common A to B Male/Male type peripheral cable, the kind that's usually used for printers. Compatible with most SFE designed USB boards as well as USB Arduino boards like the Uno. If you're still trying to wrap your head around the world of USB cables, why not check out our USB Buying Guide? Features: 6 Feet ...

                                                                                                              Limited Stock
                                                                                                              USB Cable Extension - 1.5 Foot
                                                                                                              Price: $3.90 inc GST
                                                                                                              $3.90 inc GST
                                                                                                              Sparkfun

                                                                                                                This is a 1.5' long USB extension cable equipped with type A male connector on one end to plug into your computer and a type A female connector at the other that allows for a second USB cable to be...

                                                                                                                This is a 1.5' long USB extension cable equipped with type A male connector on one end to plug into your computer and a type A female connector at the other that allows for a second USB cable to be inserted. This cable is perfect for adding a periphery that utilizes USB without having it plugged directly into your computer while not cluttering your work area with its excess length. We use this cable a lot with MicroViews, RFduinos, and USB Breakouts. ...

                                                                                                                Limited Stock
                                                                                                                USB micro-B Cable - 6 Foot
                                                                                                                Price: $8.71 inc GST
                                                                                                                $8.71 inc GST
                                                                                                                Sparkfun

                                                                                                                  USB 2.0 type A to micro USB 5-pin. This is a new, smaller connector for USB devices. Micro USB connectors are about half the height of mini USB. Micro USB is found on newer hand held devices like...

                                                                                                                  USB 2.0 type A to micro USB 5-pin. This is a new, smaller connector for USB devices. Micro USB connectors are about half the height of mini USB. Micro USB is found on newer hand held devices like cell phones and portable media devices. Works great with the Google Nexus One. Cable color and shape may vary slightly from image as our stock rotates. If you're still trying to wrap your head around the world of USB cables, why not check out our USB Buying Guide? Features: 6 glorious feet ...

                                                                                                                  Limited Stock
                                                                                                                  USB Micro-B Cable - 6"
                                                                                                                  Price: $4.66 inc GST
                                                                                                                  $4.66 inc GST
                                                                                                                  Sparkfun

                                                                                                                    This is a USB 2.0 type A to Micro-B 5-pin black cable. You know, the mini-B connector that usually comes with cell phones, Cameras, MP3 players, etc. We specifically like these 6" long cables...

                                                                                                                    This is a USB 2.0 type A to Micro-B 5-pin black cable. You know, the mini-B connector that usually comes with cell phones, Cameras, MP3 players, etc. We specifically like these 6" long cables because using USB peripherals in projects within a small enclosure is much easier these days, and most times you really don't need six feet of cable to do that. You can still use this USB cable with our Micro-USB LiPo Charger Basic, Pro Micros, Micro-B USB breakout, or anything else that utilizes a...

                                                                                                                    Limited Stock
                                                                                                                    Hot!
                                                                                                                    USB Weather Board
                                                                                                                    Price: $100.48 inc GST
                                                                                                                    Was $179.89 inc GST
                                                                                                                    Sparkfun

                                                                                                                      USB Weather Board Description: Got weather? This board can handle it. The USB Weather Board includes onboard sensors for barometric pressure, humidity, temperature, and light level. We've also added...

                                                                                                                      USB Weather Board Description: Got weather? This board can handle it. The USB Weather Board includes onboard sensors for barometric pressure, humidity, temperature, and light level. We've also added headers in the new version so you can connect the board to our weather meters (not included), adding sensors for wind speed, wind direction, and rainfall. You can send all this data to a computer or datalogger via mini-USB cable, TTL serial (3.3V), or wirelessly via Bluetooth or XBee (not...

                                                                                                                      Limited Stock
                                                                                                                      Voltage Regulator - 5V
                                                                                                                      Price: $1.71 inc GST
                                                                                                                      $1.71 inc GST
                                                                                                                      Sparkfun

                                                                                                                        This is the basic L7805 voltage regulator, a three-terminal positive regulator with a 5V fixed output voltage. This fixed regulator provides a local regulation, internal current limiting, thermal...

                                                                                                                        This is the basic L7805 voltage regulator, a three-terminal positive regulator with a 5V fixed output voltage. This fixed regulator provides a local regulation, internal current limiting, thermal shut-down control, and safe area protection for your project. Each one of these voltage regulators can output a max current of 1.5A. Features: Output Voltage: 5V Output Current: 1.5A Thermal Overload Protection Short Circuit Protection Output Transition SOA Protection Documents: Datasheet Fixed Power...

                                                                                                                        Limited Stock
                                                                                                                        Hot!
                                                                                                                        WS2801 Breakout
                                                                                                                        Price: $6.41 inc GST
                                                                                                                        Was $6.89 inc GST
                                                                                                                        Sparkfun

                                                                                                                          WS2801 Breakout Description: This is a breakout board for the WS2801 RGB LED controller, the same IC used in our addressable RGB LED strips. The board comes with the chip on one side and an RGB LED...

                                                                                                                          WS2801 Breakout Description: This is a breakout board for the WS2801 RGB LED controller, the same IC used in our addressable RGB LED strips. The board comes with the chip on one side and an RGB LED on the other. Several of these breakouts can be chained together to form a display or an addressable string. Voltage, ground, clock and data are broken out as input on one side and output on the other to standard 0.1" spaced headers. Documents: Schematic Eagle Files Datasheet (WS2801) Datasheet (RGB...

                                                                                                                          Limited Stock
                                                                                                                          XBee 3 Module - RP-SMA Antenna
                                                                                                                          Price: $38.89 inc GST
                                                                                                                          $38.89 inc GST
                                                                                                                          Sparkfun

                                                                                                                            After years of popularity with the XBee Series 1 and XBee Series 2, we now have the XBee Series 3 which brings the best of both worlds. XBee 3 not only handles 802.15.4, and ZigBee, but also BLE...

                                                                                                                            After years of popularity with the XBee Series 1 and XBee Series 2, we now have the XBee Series 3 which brings the best of both worlds. XBee 3 not only handles 802.15.4, and ZigBee, but also BLE protocols and you can now talk to the modules over UART or SPI as well. With a 200ft indoor range, or 4000ft outdoor/line-of-sight range, you can set up a mesh network to talk to or communicate with various devices around your house, work, or other area. This module has the familiar XBee package while...

                                                                                                                            Limited Stock
                                                                                                                            Hot!
                                                                                                                            XBee Pro 63mW PCB Antenna - Series 2B (ZigBee Mesh)
                                                                                                                            Price: $66.99 inc GST
                                                                                                                            Was $90.08 inc GST
                                                                                                                            Sparkfun

                                                                                                                              "This is the XBee XBP24-BZ7PIT-004 module from Digi. The new Series 2B improves upon the power output and data protocol of the Pro Series2. Series 2B modules allow you to create complex mesh...

                                                                                                                              "This is the XBee XBP24-BZ7PIT-004 module from Digi. The new Series 2B improves upon the power output and data protocol of the Pro Series2. Series 2B modules allow you to create complex mesh networks based on the XBee ZB ZigBee mesh firmware. These modules allow a very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported. Series 2B modules use a different hardware configuration...

                                                                                                                              Limited Stock
                                                                                                                              Sale!
                                                                                                                              XBee WiFi Module - RP-SMA Connector
                                                                                                                              Price: $80.25 inc GST
                                                                                                                              $80.25 inc GST
                                                                                                                              Sparkfun

                                                                                                                                "This is the XBee WiFi Module with RP-SMA connector from Digi. XBee WiFi embedded RF modules provide simple serial to IEEE 802.11 connectivity. By bridging the low-power/low-cost requirements of...

                                                                                                                                "This is the XBee WiFi Module with RP-SMA connector from Digi. XBee WiFi embedded RF modules provide simple serial to IEEE 802.11 connectivity. By bridging the low-power/low-cost requirements of wireless device networking with the proven infrastructure of 802.11, the XBee WiFi creates new wireless opportunities for energy management, process and factory automation, wireless sensor networks, intelligent asset management and more. Focused on the rigorous requirements of these wireless device...

                                                                                                                                Limited Stock
                                                                                                                                XT60 Connectors - Male/Female Pair
                                                                                                                                Price: $3.25 inc GST
                                                                                                                                $3.25 inc GST
                                                                                                                                Sparkfun

                                                                                                                                  These connectors are made from high-temp nylon with gold-plated spring pins or sockets molded in. The shape of this generic XT60 prevents reverse polarity, and when plugged in the connection is...

                                                                                                                                  These connectors are made from high-temp nylon with gold-plated spring pins or sockets molded in. The shape of this generic XT60 prevents reverse polarity, and when plugged in the connection is super-solid. Perfect for applications up to 65A continuous draw. Sold in pairs of 1 male and 1 female connector. Documents: Dimensional Drawing ...

                                                                                                                                  Limited Stock