SparkFun Parts and Devices

Need range? 2.4GHz Large Duck Antenna 5dBi with Reverse Polarized - SMA RF connector. Perfect for prototyping with our RF ICs. 50 ohm impedance. This antenna mates nicely with the Reverse Polarized...

Need range? 2.4GHz Large Duck Antenna 5dBi with Reverse Polarized - SMA RF connector. Perfect for prototyping with our RF ICs. 50 ohm impedance. This antenna mates nicely with the Reverse Polarized SMA Connector. Features: 0.5x7.7" Documents: Datasheet

This is a 10-pin socket with 2mm pitch that mates with the popular XBee radio from Digi. Use this small part to avoid having to solder your precious radio to a PCB. You'll need two of these sockets...

This is a 10-pin socket with 2mm pitch that mates with the popular XBee radio from Digi. Use this small part to avoid having to solder your precious radio to a PCB. You'll need two of these sockets to connect to all 20 pins on the XBee. These headers can also be cut to work with the RFID breakout board. Please Note: This item is sold singly, not in pairs. Documents: Datasheet ...

50 Channel D2523T Helical GPS Receiver Description: The D2523T is a compact GPS smart-antenna engine board, which comes equipped with a Sarantel GeoHelix high-gain active antenna and GPS receiver...

50 Channel D2523T Helical GPS Receiver Description: The D2523T is a compact GPS smart-antenna engine board, which comes equipped with a Sarantel GeoHelix high-gain active antenna and GPS receiver circuits. The module is based around the high performance 50-channel u-blox 5 platform. The omni-directional antenna provides great sensitivity, even when you don't have a clear view of the sky. Whether this receiver is in your pocket or under your car seat, you are likely to pickup a rock solid GPS...

This is a basic, 4-digit 7-segment display - yellow in color. It has a common anode. The display features one decimal point per digit, and individually controllable apostrophe and colon points. The...

This is a basic, 4-digit 7-segment display - yellow in color. It has a common anode. The display features one decimal point per digit, and individually controllable apostrophe and colon points. The LEDs have a forward voltage of 2.1VDC and a max forward current of 20mA. The hardware interface is sixteen (two rows of eight) through-hole pins. We carry this same display in red, green, and blue. Features: Overall Display: 40.18 x 12.8 mm (1.58 x 0.50") Digit Height: 10mm (0.39") Documents:...

Your basic 7-segment LED, but in blue! Common anode. Two decimal points, but only the one on the right is wired. Digit height is 0.6". Overall height is 1". Check out this tutorial on how to use...

Your basic 7-segment LED, but in blue! Common anode. Two decimal points, but only the one on the right is wired. Digit height is 0.6". Overall height is 1". Check out this tutorial on how to use this product with the 74HC595 Shift Register and Arduino. Thanks Patrick and Mycha! Documents: Datasheet Arduino Library (Thanks Derek!) ...

9 Degrees of Freedom - MPU-9150 Breakout Description: The MPU-9150 is the world’s first 9-axis MotionTracking device designed for the low power, low cost, and high performance requirements of...

9 Degrees of Freedom - MPU-9150 Breakout Description: The MPU-9150 is the world’s first 9-axis MotionTracking device designed for the low power, low cost, and high performance requirements of consumer electronics equipment including smartphones, tablets and wearable sensors. And guess what? You get to play with it. This breakout board makes it easy to prototype with the InvenSense MPU-9150 by breaking out all the pins you need to standard 0.1" spaced headers. The board also provides I2C pullup...

Classic 9V snap connector terminated with 2-pin polarized Molex connector with 0.1" spacing. The cable is 26AWG and is 5" in length. ...

Classic 9V snap connector terminated with 2-pin polarized Molex connector with 0.1" spacing. The cable is 26AWG and is 5" in length.

This simple cable has so many uses! Plug the 9 volt battery clip onto a standard 9V battery and connect the other end to anything with a 5.5x2.1mm, center-positive barrel jack. Use this cable to...

This simple cable has so many uses! Plug the 9 volt battery clip onto a standard 9V battery and connect the other end to anything with a 5.5x2.1mm, center-positive barrel jack. Use this cable to battery-power any device that needs 9V and has an on-board barrel jack - it works great for Arduinos, development boards, evaluation boards, and more! ...

ADH8066 Evaluation Board Description: The evaluation board for the ADH8066 Cell Module breaks out all the pins to the module and provides you with the necessary support hardware to get you up and...

ADH8066 Evaluation Board Description: The evaluation board for the ADH8066 Cell Module breaks out all the pins to the module and provides you with the necessary support hardware to get you up and running. The ADH8066 board attaches to any USB port and appears as a standard com port. Power up the board with 6-12 VDC, turn on the module, and you can start sending and receiving AT commands via HyperTerminal or your favorite terminal program. The board comes assembled as shown so you don't need to...

"This pack of 4-40 screws comes with a matching hex key. Each screw is 10mm in length. These are left over production stock from the original version of the BigTime Watch Kit so they won’t be around...

"This pack of 4-40 screws comes with a matching hex key. Each screw is 10mm in length. These are left over production stock from the original version of the BigTime Watch Kit so they won’t be around for long. Includes: 4x screws 1x hex key Dimensions: 10mm long"

"These Large Insulated Alligator Clips are great for clamping anything that you don’t want to deform yet large enough to easily manipulate. Thanks to the insulated flat surface, these clips can be...

"These Large Insulated Alligator Clips are great for clamping anything that you don’t want to deform yet large enough to easily manipulate. Thanks to the insulated flat surface, these clips can be used in a variety of applications such as, gripping small wires, coin cell battery, or large pads (like on our LilyPad boards). These clips offer an open clearance of a little over 8mm, two pan head screw terminals for wire connection, and a max current limit of 10A (theoretically). Sold in single...

4-way Pacman type arcade joystick. Heavy duty design gives this joystick a great feel! Features: ABS plastic and solid alloy construction Uses 4 microswitches to detect on/off position Unique handle...

4-way Pacman type arcade joystick. Heavy duty design gives this joystick a great feel! Features: ABS plastic and solid alloy construction Uses 4 microswitches to detect on/off position Unique handle design Spring return to center Very rugged construction Rated 5A @ 125V, 3A @ 250V* Overall height: 101mm Base: 97x65mm Joystick height: 60mm Documents: Manual ...

"The Arduino Industrial 101 is a WiFi evaluation board for the Arduino 101 LGA module based on a MIPS Linux processor. With the Industrial 101 you will possess a fantastic addition to the Arduino...

"The Arduino Industrial 101 is a WiFi evaluation board for the Arduino 101 LGA module based on a MIPS Linux processor. With the Industrial 101 you will possess a fantastic addition to the Arduino family and be able to easily create IoT projects without the need for multiple shields. Similar to the Arduino Yun (in a small form-factor), the Industrial 101 integrates an ATmega32U4 and the Atheros AR9331 SoC to make a dependable evaluation resource! The onboard ATmega32u4 microcontroller has been...

It's blue! It's skinny! It's the Arduino Pro! SparkFun's minimal design approach to Arduino. This is a 3.3V Arduino running the 8MHz bootloader. Because the system voltage for this board is lower...

It's blue! It's skinny! It's the Arduino Pro! SparkFun's minimal design approach to Arduino. This is a 3.3V Arduino running the 8MHz bootloader. Because the system voltage for this board is lower than other Arduino development boards, it may not be compatible with many Arduino shields which were designed to run at 5V. The Arduino Pro 3.3V still works great with our prototyping shield so you can create your own 3.3V shields. The lower system voltage also has its advantages, like ease of use...

It's blue! It's skinny! It's the Arduino Pro! SparkFun's minimal design approach to Arduino. This is a 5V Arduino running the 16MHz bootloader in a super-sleek form factor that will fit easily into...

It's blue! It's skinny! It's the Arduino Pro! SparkFun's minimal design approach to Arduino. This is a 5V Arduino running the 16MHz bootloader in a super-sleek form factor that will fit easily into your next small project. Arduino Pro does not come with connectors populated so that you can solder in any connector or wire with any orientation you need. We recommend first time Arduino users start with the Uno R3. It's a great board that will get you up and running quickly. The Arduino Pro series...

It's blue! It's thin! It's the Arduino Pro Mini! SparkFun's minimal design approach to Arduino. This is a 5V Arduino running the 16MHz bootloader. Arduino Pro Mini does not come with connectors...

It's blue! It's thin! It's the Arduino Pro Mini! SparkFun's minimal design approach to Arduino. This is a 5V Arduino running the 16MHz bootloader. Arduino Pro Mini does not come with connectors populated so that you can solder in any connector or wire with any orientation you need. We recommend first time Arduino users start with the Uno R3. It's a great board that will get you up and running quickly. The Arduino Pro series is meant for users that understand the limitations of system voltage...

This is a 10-pin female header, with extra long legs -- great for stacking R3-compatible Arduino shields! Pins are spaced by 0.1". Documents: Datasheet ...

This is a 10-pin female header, with extra long legs -- great for stacking R3-compatible Arduino shields! Pins are spaced by 0.1". Documents: Datasheet

This is a 6-pin female header, with extra long legs -- great for stacking Arduino shields. Pins are spaced by 0.1". Documents: Datasheet ...

This is a 6-pin female header, with extra long legs -- great for stacking Arduino shields. Pins are spaced by 0.1". Documents: Datasheet

This is a 8-pin female header, with extra long legs -- great for stacking Arduino shields. Pins are spaced by 0.1". Documents: Datasheet ...

This is a 8-pin female header, with extra long legs -- great for stacking Arduino shields. Pins are spaced by 0.1". Documents: Datasheet

These headers are made to work with the Arduino Main Board, Arduino Pro, and the Arduino Mega. They are the perfect height for clearing the USB-B connector and great for stacking multiple shields....

These headers are made to work with the Arduino Main Board, Arduino Pro, and the Arduino Mega. They are the perfect height for clearing the USB-B connector and great for stacking multiple shields. This kit includes 4 headers (2 8-pin and 2 6-pin), enough to connect a shield to an Arduino Main Board. These are the same headers we use in our tutorials and with our own shields. Note: If you have a board that uses the Arduino R3 architecture which include the OREF, SCL, and SDA pins they can be...

"The ATmega128RFA1 is a portmanteau of sorts – two separate components combined to form one device; half microcontroller, half RF transciever. ATmega128RFA1 is an IEEE 802.15.4 compliant...

"The ATmega128RFA1 is a portmanteau of sorts – two separate components combined to form one device; half microcontroller, half RF transciever. ATmega128RFA1 is an IEEE 802.15.4 compliant single-chip, combining the industry- leading AVR microcontroller and best-in-class 2.4GHz RF transceiver providing industry’s highest RF performance for single-chip devices, with a link budget of 103.5dBm. The ATmega128RFA1 features Wake-on Radio, 32-bit MAC symbol counter, temperature sensor, automatic...

The name says it all on this one. An ATmega328P in DIP package, pre-loaded with the Arduino Optiboot (Uno 16MHz) Bootloader. This will allow you to use Arduino code in your custom embedded project...

The name says it all on this one. An ATmega328P in DIP package, pre-loaded with the Arduino Optiboot (Uno 16MHz) Bootloader. This will allow you to use Arduino code in your custom embedded project without having to use an actual Arduino board. To get this chip working with Arduino IDE, you will need an external 16MHz crystal or resonator, a 5V supply, and a serial connection. If you are not comfortable doing this, we recommend purchasing the Arduino Uno board that has all of these built into...

"This is a small voltage and current sense PCB. DC current is determined by measuring a voltage drop across a pair of parallel shunt resistors, then converted to a final analog voltage output by the...

"This is a small voltage and current sense PCB. DC current is determined by measuring a voltage drop across a pair of parallel shunt resistors, then converted to a final analog voltage output by the TI INA-169. Voltage sense is accomplished by scaling to 3.3V ADC range by a precision resistor divider. The PCB is supplied without leads or connectors. The pad sizes are large enough to accommodate 12 gauge heavy duty leads (see datasheet) but care must be exercised in soldering. Smaller gauge...

This is a right-angle, 24-pin Molex Mini-Fit Jr.™ connector, commonly used as the power supply connector on ATX motherboards. Two rows of twelve pins are broken out two rows of through-hole male...

This is a right-angle, 24-pin Molex Mini-Fit Jr.™ connector, commonly used as the power supply connector on ATX motherboards. Two rows of twelve pins are broken out two rows of through-hole male headers. See the datasheet below for pin spacing dimensions. Pair this connector with a standard computer power supply and you can source a number of different voltages (+3.3V, +5V, +12V, -12V, -5V) to your project.[ Documents: Dimensional Drawing ...

Low profile 3.5mm stereo audio jack. Documents: Audio 3.5mm Jack Datasheet ...

Low profile 3.5mm stereo audio jack. Documents: Audio 3.5mm Jack Datasheet

AVR ISP Shield - PTH Kit Description: Did you know that your Arduino can spawn other Arduinos? Don't worry, it can't do it autonomously so you won't wind up with a replicator situation (-gate, not...

AVR ISP Shield - PTH Kit Description: Did you know that your Arduino can spawn other Arduinos? Don't worry, it can't do it autonomously so you won't wind up with a replicator situation (-gate, not -Trek). The point is, the ArduinoISP sketch allows your Arduino to act as a programmer. You can use this awesome power to burn bootloaders onto ATMega chips, turning them into Arduino-compatible microcontrollers! In the past, this required a breadboard and a whole mess of jumper wires but we've just...

These are various leaded cables for attaching to multimeters, power supplies, oscilloscopes, function generators, etc. Cables come in red/black pairs. Features: 36" Long ...

These are various leaded cables for attaching to multimeters, power supplies, oscilloscopes, function generators, etc. Cables come in red/black pairs. Features: 36" Long

The MPL115A1 is a digital barometer that uses MEMs technology to give accurate pressure measurements between 50kPa and 115kPa. We stock the SPI interface version of the sensor. Average current...

The MPL115A1 is a digital barometer that uses MEMs technology to give accurate pressure measurements between 50kPa and 115kPa. We stock the SPI interface version of the sensor. Average current consumption is 10µA at one measurement per second. The sensor outputs both temperature and pressure readings on the SPI bus. See page 3 of the datasheet for information on how to take readings from the pressure sensor. Breakout board coming soon! Features: Wide supply voltage range -40°C to 105°C maximum...

We use barrel jacks a lot around here and sometimes we need to pop a switch into the mix. That usually means hacking up a perfectly good barrel jack extension cable, but the whole point of using the...

We use barrel jacks a lot around here and sometimes we need to pop a switch into the mix. That usually means hacking up a perfectly good barrel jack extension cable, but the whole point of using the barrel jacks was so that we wouldn't have to hack things apart... Well, we found a solution: The Barrel Jack Power Switch. Okay, it's nothing fancy but it *is *really useful. Plug your power supply into one end and the other into your project and, just like that, you've got a power switch! The...

This is a basic 16 character by 2 line display with a snazzy black background with white characters. Utilizes the extremely common HD44780 parallel interface chipset (datasheet). Interface code is...

This is a basic 16 character by 2 line display with a snazzy black background with white characters. Utilizes the extremely common HD44780 parallel interface chipset (datasheet). Interface code is freely available. You will need ~11 general I/O pins to interface to this LCD screen. Includes white LED backlight. Get Started with the Basic Character LCD Guide Features: 3.15" x 1.425" Documents: Hookup Guide Datasheet mbed Example AVR Example Character Generator ...

"This is a basic 20 character by 4 line display. Utilizes the extremely common HD44780 parallel interface chipset (datasheet). Interface code is freely available. You will need ~11 general I/O pins...

"This is a basic 20 character by 4 line display. Utilizes the extremely common HD44780 parallel interface chipset (datasheet). Interface code is freely available. You will need ~11 general I/O pins to interface to this LCD screen. Includes LED backlight. Documents: Datasheet mbed Example AVR Example Character Generator Dimensions: 3.86 x 2.36 x 0.55"" ...

The Big Easy Driver, designed by Brian Schmalz, is a stepper motor driver board for bi-polar stepper motors up to a max 2A/phase. It is based on the Allegro A4988 stepper driver chip. It's the next...

The Big Easy Driver, designed by Brian Schmalz, is a stepper motor driver board for bi-polar stepper motors up to a max 2A/phase. It is based on the Allegro A4988 stepper driver chip. It's the next version of the popular Easy Driver board. Each Big Easy Driver can drive up to a max of 2A per phase of a bi-polar stepper motor. It is a chopper microstepping driver which defaults to 16 step microstepping mode. It can take a maximum motor drive voltage of around 30V, and includes on-board 5V/3.3V...

This is a black insulated binding post. These binding posts do accept banana plugs, and are a great way to connect single-wire leads. The colored cap screws up and down, and is designed to clamp on...

This is a black insulated binding post. These binding posts do accept banana plugs, and are a great way to connect single-wire leads. The colored cap screws up and down, and is designed to clamp on the connecting wire. These binding posts are sold individually. We also carry a similar red binding post.

This is a red insulated binding post. These binding posts do accept banana plugs, and are a great way to connect single-wire leads. The colored cap screws up and down, and is designed to clamp on...

This is a red insulated binding post. These binding posts do accept banana plugs, and are a great way to connect single-wire leads. The colored cap screws up and down, and is designed to clamp on the connecting wire. These binding posts are sold individually. We also carry a similar black binding post.

The Binho Nova Multi-Protocol USB Host Adapter allows one to interface their computer directly to hardware circuits. This device is powered by the USB connection to the host PC and is also able to...

The Binho Nova Multi-Protocol USB Host Adapter allows one to interface their computer directly to hardware circuits. This device is powered by the USB connection to the host PC and is also able to provide downstream power to test circuits. The Binho Nova Multi-Protocol USB Host Adapter features 5 signal pins, one x 3v3 pin, one x VUSB pin, and three x GND pins on its 10pin wire harness. The wire harness terminates with a female 1.27mm 2x5 IDC connector. In IO Mode, the five signal pins can be...

Knobs are a great way to finish off your project and make it easier to adjust the level of your death ray. This knob mates to a 0.25" shaft with a set screw. Features: 15mm high 19mm diameter ...

Knobs are a great way to finish off your project and make it easier to adjust the level of your death ray. This knob mates to a 0.25" shaft with a set screw. Features: 15mm high 19mm diameter

Knobs are a great way to finish off your project and make it easier to adjust the level of your death ray. This knob mates to a 6mm (+/- 0.3mm) shaft. The knob slides onto the potentiometer and...

Knobs are a great way to finish off your project and make it easier to adjust the level of your death ray. This knob mates to a 6mm (+/- 0.3mm) shaft. The knob slides onto the potentiometer and holds tightly with a strong friction fit. The main body of these knobs is metal with a plastic insert. The outside is knurled for precise adjustment. Features: 14mm high 24mm diameter Documents: Dimensional Drawing ...

Bluetooth & LiPo Add-On for Makey Makey Description: The MaKey MaKey is really cool, but wouldn't it be cooler if it wasn't tethered to your computer? There's only one way to find out: Go...

Bluetooth & LiPo Add-On for Makey Makey Description: The MaKey MaKey is really cool, but wouldn't it be cooler if it wasn't tethered to your computer? There's only one way to find out: Go wireless. Our Bluetooth & LiPo Add-On for MaKey MaKey frees your MaKey invention from the bonds of USB wired connection. Data is passed over a Bluetooth HID connection to your Bluetooth enabled computer which will recognize it as a Bluetooth wireless keyboard. Power is handled through a 2-pin JST...

Bluetooth Mate Description: The Bluetooth Mate is very similar to our BlueSMiRF modem, but it is designed specifically to be used with our Arduino Pros and LilyPad Arduinos. These modems work as a...

Bluetooth Mate Description: The Bluetooth Mate is very similar to our BlueSMiRF modem, but it is designed specifically to be used with our Arduino Pros and LilyPad Arduinos. These modems work as a serial (RX/TX) pipe, and are a great wireless replacement for serial cables. Any serial stream from 9600 to 115200bps can be passed seamlessly from your computer to your target. We've tested these units successfully over open air at 350ft (106m)! Bluetooth Mate has the same pin out as the FTDI Basic,...

Bluetooth Module Breakout - Roving Networks (RN-41) Description: This is a simple breakout for the Roving Networks Bluetooth module. All pertinent pins are broken out and labeled. This new version's...

Bluetooth Module Breakout - Roving Networks (RN-41) Description: This is a simple breakout for the Roving Networks Bluetooth module. All pertinent pins are broken out and labeled. This new version's headers are unpopulated. Check below for appropriate headers. The module from Roving Networks is powerful, small, and very easy to use. This Bluetooth module is designed to replace serial cables. The Bluetooth stack is completely encapsulated. The end user just sees serial characters being...

This is a handy little Bluetooth USB mini-adapter. This adapter supports Bluetooth v2.0 class 1 and has a maximum distance of up to 100m. The adapter also includes an indicator LED. Great for...

This is a handy little Bluetooth USB mini-adapter. This adapter supports Bluetooth v2.0 class 1 and has a maximum distance of up to 100m. The adapter also includes an indicator LED. Great for laptops and if you're on the go! This device does not include any drivers or software, however, you shouldn't need any as it supports the native Windows Bluetooth stack (Windows XP, Vista, 7). Plug it in and Windows should handle the rest. Of course, we couldn't resist taking it apart. Please note: Many...

The BNC probe kit includes a 20MHz professional probe with hook and tip as well as a couple converters to connect the probe to either a BNC jack, RCA jack, or a PCB mount. Each Probe is 4ft (1.2m)...

The BNC probe kit includes a 20MHz professional probe with hook and tip as well as a couple converters to connect the probe to either a BNC jack, RCA jack, or a PCB mount. Each Probe is 4ft (1.2m) in length and is perfect for most midrange applications. This kit was designed for use with our Digital Oscilloscope Kit, but can be used in a variety of other way or with other parts. Includes: 20MHz professional probe with tip, hook connector and ground alligator clip BNC-to-RCA(male)...

This blue Mini Breadboard is a great way to prototype your small projects! With 170 tie points there's just enough room to build and test simple circuits; They're also great for breaking out DIP...

This blue Mini Breadboard is a great way to prototype your small projects! With 170 tie points there's just enough room to build and test simple circuits; They're also great for breaking out DIP package ICs to jumper wires! If you run out of room, no worries, these mini breadboards can be snapped together to form larger stretches of board. It has a peel and stick adhesive backing as well as two mounting holes for M2 screws so you can anchor it down. Note: These will not connect securely with...

This green Mini Breadboard is a great way to prototype your small projects! With 170 tie points there's just enough room to build and test simple circuits; They're also great for breaking out DIP...

This green Mini Breadboard is a great way to prototype your small projects! With 170 tie points there's just enough room to build and test simple circuits; They're also great for breaking out DIP package ICs to jumper wires! If you run out of room, no worries, these mini breadboards can be snapped together to form larger stretches of board. It has a peel and stick adhesive backing as well as two mounting holes for M2 screws so you can anchor it down. Note: These will not connect securely with...

This red Mini Breadboard is a great way to prototype your small projects! With 170 tie points there's just enough room to build and test simple circuits; They're also great for breaking out DIP...

This red Mini Breadboard is a great way to prototype your small projects! With 170 tie points there's just enough room to build and test simple circuits; They're also great for breaking out DIP package ICs to jumper wires! If you run out of room, no worries, these mini breadboards can be snapped together to form larger stretches of board. It has a peel and stick adhesive backing as well as two mounting holes for M2 screws so you can anchor it down. Note: These will not connect securely with...

This white Mini Breadboard is a great way to prototype your small projects! With 170 tie points there's just enough room to build and test simple circuits; They're also great for breaking out DIP...

This white Mini Breadboard is a great way to prototype your small projects! With 170 tie points there's just enough room to build and test simple circuits; They're also great for breaking out DIP package ICs to jumper wires! If you run out of room, no worries, these mini breadboards can be snapped together to form larger stretches of board. It has a peel and stick adhesive backing as well as two mounting holes for M2 screws so you can anchor it down. Note: These will not connect securely with...

Description: Ever wonder what goes on inside these things? Well this clear bread board might enlighten. Beyond the clear plastic, this is really just a regular, solderless breadboard. It has 2 power...

Description: Ever wonder what goes on inside these things? Well this clear bread board might enlighten. Beyond the clear plastic, this is really just a regular, solderless breadboard. It has 2 power buses, 30 columns, and 10 rows - a total of 400 tie in points. All pins are spaced by a standard 0.1". The two sets of five rows are separated by about 0.3", perfect for straddling a DIP package over. The board accepts wire sizes in the range of 29-20AWG. This board also has a self-adhesive on the...

These are a longer version of our standard break away headers. They are 20mm long which allows you use them socket to socket. The plastic separator can be slid up or down to accommodate your...

These are a longer version of our standard break away headers. They are 20mm long which allows you use them socket to socket. The plastic separator can be slid up or down to accommodate your needs. You will get a row of 40 pins. They can be broken or snipped to length. Features: Pin Style: Square Pins Number of Pins: 40 Pin Spacing: 0.1" (2.54 mm) Pin Length: 20 mm Documents: Dimensional Drawing ...

This is a simple breakout board for the popular XBee product from Digi. This board breaks out all 20 pins of the XBee to a 0.1" standard spacing dual row header. The spacing between 0.1" headers is...

This is a simple breakout board for the popular XBee product from Digi. This board breaks out all 20 pins of the XBee to a 0.1" standard spacing dual row header. The spacing between 0.1" headers is 0.5" making it breadboard DIP friendly. We highly recommend using the female sockets to avoid having to solder the XBee permanently to the breakout board. This is the PCB only. Please order the accompanying 2mm sockets (you'll need 2!) and 0.1" headers below. Documents: Schematic Eagle Files 5V...

This is an interface cable for the Bus Pirate, designed to connect to its 2x5 I/O header. The cable's connector is composed of two rows of five 0.1" spaced pins; it's also polarized, as is the...

This is an interface cable for the Bus Pirate, designed to connect to its 2x5 I/O header. The cable's connector is composed of two rows of five 0.1" spaced pins; it's also polarized, as is the mating connector on-board the Bus Pirate, so you can only connect the cable in one direction. The leads of the cable are terminated with female ends to mate with test hooks. The pin-out of the connector is documented here. ...

This a simple breakout board for the button pads. Each LED and button is brought out to the side connectors. The connectors are soldered to the back side of the PCB. We recommend trimming the...

This a simple breakout board for the button pads. Each LED and button is brought out to the side connectors. The connectors are soldered to the back side of the PCB. We recommend trimming the connector leads on the button side as short as possible to reduce the deflection of the pad. Now with footprints for diodes! Use the super cheap 1N4148 through-hole diodes. These can be used to isolate the switches to make for a bit easier decoding. Documents: Schematic Eagle Files Hookup Guide Datasheet...

Resonators function like crystals, but are a lower cost solution that does not require external caps. These resonators are +/-0.5% or better from -20C-+80C. These resonators have built-in load...

Resonators function like crystals, but are a lower cost solution that does not require external caps. These resonators are +/-0.5% or better from -20C-+80C. These resonators have built-in load capacitors so no external caps are needed. Documents: Datasheet

These clamping hubs are a great and cost-effective choice when attaching hub mount gears or wheels to shafts or tubes and can be a better option than set screw hubs if you don't want to risk...

These clamping hubs are a great and cost-effective choice when attaching hub mount gears or wheels to shafts or tubes and can be a better option than set screw hubs if you don't want to risk damaging whatever you need clamped. These clamping hubs have a 5mm bore, four 6-32 tapped holes, one 6-32 machine screw for tightening, and utilizes the 0.77" hub pattern. Actobotics is a robotics building system based around extruded aluminum channels, gears, precision shafts, and ball bearings. Thanks to...

"This is a high-quality color CMOS camera module. Power the CM-32 module, hook up any display, monitor, or LCD screen with an RCA input and get vivid color video at 728x488 resolution. Module is...

"This is a high-quality color CMOS camera module. Power the CM-32 module, hook up any display, monitor, or LCD screen with an RCA input and get vivid color video at 728x488 resolution. Module is easily mountable and has a wide operating voltage (6V to 20V). Comes with high quality optics, all the on board circuitry to output RCA signal, and cable harness. Features: 728 x 488 Resolution 6V to 20V input 50mA (at 12V) Documents: Datasheet " ...

This is a coin cell holder for the common CR2032 type battery. The holder has a neat pop-in, pop-out feature that makes changing the battery easy. The feet of the holder have a small hole that allow...

This is a coin cell holder for the common CR2032 type battery. The holder has a neat pop-in, pop-out feature that makes changing the battery easy. The feet of the holder have a small hole that allow it to be sewn without modification. Documents: Datasheet

Now for all of your coin cell battery surface mount needs, the 20mm SMD Coin Cell Holder. This holder fits our 20mm Lithium Ion coin cell battery and holds the battery in place with friction. The...

Now for all of your coin cell battery surface mount needs, the 20mm SMD Coin Cell Holder. This holder fits our 20mm Lithium Ion coin cell battery and holds the battery in place with friction. The metal housing connects to the positive (+) side of the battery and the PCB pad underneath is connected to the negative (-) side. Documents: Datasheet ...

Color 24-Bit LCD 4-3in PSP Touch Screen Description: This is a 4-wire resistive analog touch screen. Intended to mate with the 24-Bit PSP display, this unit comes with a handy adhesive backing to...

Color 24-Bit LCD 4-3in PSP Touch Screen Description: This is a 4-wire resistive analog touch screen. Intended to mate with the 24-Bit PSP display, this unit comes with a handy adhesive backing to stick to the PSP display. 4-wire ribbon with 1mm pitch. This touch screen is not intended to be hacked into an off-the-shelf Play Station Portable. It is solely meant to be a nice add-on to our 24-Bit color display. Hantouch part # : HT043A-NCOFD52 Check out SparkFuns touchscreen tutorial! Please be...

Color 24-Bit LCD 4-3in PSP Touch Screen Connector BreakoutDescription: This is the SMD connector for the PSP touch screen. 4-pin right angle good, friction fit connector with 1 mm pitch.This...

Color 24-Bit LCD 4-3in PSP Touch Screen Connector BreakoutDescription: This is the SMD connector for the PSP touch screen. 4-pin right angle good, friction fit connector with 1 mm pitch.This connector is compatible with the PSP Touch Screen NOT the Sharp Color 24-Bit LCD.Documents: Connector Datasheet Schematic ...

This is a 35mm concave momentary push button similar to the ones you find on arcade games. Simple screw in design. Perfect for mashing. This button has a great tactile, 'clicky' feel. Features:...

This is a 35mm concave momentary push button similar to the ones you find on arcade games. Simple screw in design. Perfect for mashing. This button has a great tactile, 'clicky' feel. Features: Concave plunger design Durable nylon material Microswitch: max 3A @ 120 VAC Microswitch reliability tested to 10,000,000 cycles Includes 3 terminal microswitch Net weight: 25g* Cap diameter: 35mm Overall height: 65mm Mounting hole: 1 1/8th inch paddle bit (1.125" / 28mm) ...

Copper tape has countless applications in electronics from creating low-profile traces for electrical components to RF-shielding and antenna-making. Copper tape is even used to join things together...

Copper tape has countless applications in electronics from creating low-profile traces for electrical components to RF-shielding and antenna-making. Copper tape is even used to join things together using solder, like the stained glass on Tiffany lamps. This copper tape is adhesive-backed, 5mm wide and comes in rolls of 50 feet. Thickness: 3 mil

"Standard frequency crystals - use these crystals to provide a clock input to your microprocessor. Rated at 20pF capacitance and +/- 50ppm stability. Low profile HC49/US Package." ...

"Standard frequency crystals - use these crystals to provide a clock input to your microprocessor. Rated at 20pF capacitance and +/- 50ppm stability. Low profile HC49/US Package."

This adapter allows you to connect a barrel jack connector to bare wires. One end has screw terminals and the other has a 5.5x2.1mm, center-positive male barrel jack. If you need to connect bare...

This adapter allows you to connect a barrel jack connector to bare wires. One end has screw terminals and the other has a 5.5x2.1mm, center-positive male barrel jack. If you need to connect bare wires to a barrel jack on an Arduino or a development board, this might be the simple solution. Please be aware that the max current for this adapter is 10A.

Do you have an R/C vehicle battery pack that desperately needs a Deans connector? With our new M/F Deans connector pair, you'll have just what you need to safely and securely connect your battery or...

Do you have an R/C vehicle battery pack that desperately needs a Deans connector? With our new M/F Deans connector pair, you'll have just what you need to safely and securely connect your battery or anything else that requires a mini T Plug. Each pack comes with one male and one female Deans connector and each can support a current of, up to, 30A. Documents: Dimensional Drawing ...

Mini Diagonal Cutters. These are great little cutters! A must have for clipping leads and extra solder tails. 4" long.

Mini Diagonal Cutters. These are great little cutters! A must have for clipping leads and extra solder tails. 4" long.

The digital multimeter (DMM) is an essential tool in every electronic enthusiasts arsenal. The SparkFun Digital Multimeter, however, is not your average multimeter, it features a loud continuity...

The digital multimeter (DMM) is an essential tool in every electronic enthusiasts arsenal. The SparkFun Digital Multimeter, however, is not your average multimeter, it features a loud continuity sound, current/voltage sense, and quality probes. You can use the multimeter to measure DC and AC voltage, DC current, resistance, continuity, and test diodes. With this version we've done away with the bright flashy colors that can get us into trouble and gone with a nice, neutral gray. This...

DIP Sockets Solder Tail - 24-Pin 0.6 Description: Dip sockets for all your prototyping needs. If you've ever had to de-solder a dip part from a circuit board, you know how valuable these are! Number...

DIP Sockets Solder Tail - 24-Pin 0.6 Description: Dip sockets for all your prototyping needs. If you've ever had to de-solder a dip part from a circuit board, you know how valuable these are! Number of pins include: 8, 14, 16, 18, 24, 28, and 40. This is a 600mil wide 24-pin socket.

The EasyDriver is a simple to use stepper motor driver, compatible with anything that can output a digital 0 to 5V pulse (or 0 to 3.3V pulse if you solder SJ2 closed on the EasyDriver). The...

The EasyDriver is a simple to use stepper motor driver, compatible with anything that can output a digital 0 to 5V pulse (or 0 to 3.3V pulse if you solder SJ2 closed on the EasyDriver). The EasyDriver requires a 6V to 30V supply to power the motor and can power any voltage of stepper motor. The EasyDriver has an on board voltage regulator for the digital interface that can be set to 5V or 3.3V. Connect a 4-wire stepper motor and a microcontroller and you've got precision motor control!...

Small electret microphone. Useful in acoustic and audio applications. Documents: Datasheet Example Audio LED control project by Adam Greig ...

Small electret microphone. Useful in acoustic and audio applications. Documents: Datasheet Example Audio LED control project by Adam Greig

Electric Imp Shield Description: If you aren't familiar with the Electric Imp, it essentially provides an easy, integrated way to connect almost any hardware device both to other devices and to...

Electric Imp Shield Description: If you aren't familiar with the Electric Imp, it essentially provides an easy, integrated way to connect almost any hardware device both to other devices and to internet services. It's more than just a WiFi card, or even a WiFi module with processing built in - it's an integrated platform that deals with the drudgery of connectivity, allowing you to concentrate on the application instead of the mechanics. Of course, if you're developing for it you'll need a way...

FEZ Panda Description: FEZ Panda is a tiny open-source board running Microsoft .NET Micro Framework. This means, you can write code with much more efficiency using C# programming language under free...

FEZ Panda Description: FEZ Panda is a tiny open-source board running Microsoft .NET Micro Framework. This means, you can write code with much more efficiency using C# programming language under free Microsoft Visual C# express. FEZ Panda also includes JTAG access for those who wish to use their own firmware instead of NETMF. Using an Arduino-form-factor, you can use just about any Arduino shield. In addition, many libraries are already included like FAT file system, networking, threading, USB...

This very long force sensitive resistor - over 2 feet - has a sensing area of 0.25x24". This FSR from Interlink Electronics will vary its resistance depending on how much pressure is being applied...

This very long force sensitive resistor - over 2 feet - has a sensing area of 0.25x24". This FSR from Interlink Electronics will vary its resistance depending on how much pressure is being applied to the sensing area. The harder the force, the lower the resistance. When no pressure is being applied to the FSR its resistance will be larger than 1MΩ. This FSR can sense applied force anywhere in the range of 100g-10kg. Two pins extend from the bottom of the sensor with 0.1" pitch making it bread...

Do you still looking for the relay module for the Micro: bit? Here we had combined the relay with the Micro: bit and you can use Micro: bit to control 4 relays at the same time. Features Apply to...

Do you still looking for the relay module for the Micro: bit? Here we had combined the relay with the Micro: bit and you can use Micro: bit to control 4 relays at the same time. Features Apply to Micro: bit. Four channel relay. Specifications Input voltage: 5v Load voltage and current: 3A 120VAC/ 24VDC Working mode: NC/ NO Package list Four Channel Relay for Micro: bit x 1 Wiki & External links User manual (wiki link) ...

Embedded antenna for small, mobile applications. Basic unpackaged antenna with LNA. 5inch cable terminated with standard male SMA connector. Match it with any SMA interface cable to create a truly...

Embedded antenna for small, mobile applications. Basic unpackaged antenna with LNA. 5inch cable terminated with standard male SMA connector. Match it with any SMA interface cable to create a truly small GPS prototype! This unit works very well out of the box, but the fully packaged antennas have better strain relief where the SMA cable meets the antenna housing. If you plan on using this antenna in a vibration intensive application, we recommend you reinforce the connection with epoxy or Shoe...

Faster, cheaper, smaller, better, right? The SN754410 Quad Half H-Bridge is just that. Capable of driving high voltage motors using TTL 5V logic levels, the SN754410 can drive 4.5V up to 36V at 1A...

Faster, cheaper, smaller, better, right? The SN754410 Quad Half H-Bridge is just that. Capable of driving high voltage motors using TTL 5V logic levels, the SN754410 can drive 4.5V up to 36V at 1A continuous output current! Please see datasheet for more information. This is a pin to pin compatible replacement for the L293D. **Datasheets: **SN754410

Be still my beating heart! With the heART Surface Mount Soldering Kit you will be able to learn the basics of SMD soldering by being able to assemble a beating heart pendant! Each heART kit takes...

Be still my beating heart! With the heART Surface Mount Soldering Kit you will be able to learn the basics of SMD soldering by being able to assemble a beating heart pendant! Each heART kit takes about 20-40min to assemble depending on your soldering skill level with basic soldering materials (not included). This little kit provides a great learning tool to help you practice and improve your overall soldering skills without proving to be an impossible challenge! Every heART pendant kit...

These are a pair of right angle, hobby gearmotors from DAGU. These gearmotors are the same ones utilized in the Magician Chassis and RedBot Kit and offer a cheap and easy to use setup to get your...

These are a pair of right angle, hobby gearmotors from DAGU. These gearmotors are the same ones utilized in the Magician Chassis and RedBot Kit and offer a cheap and easy to use setup to get your wheels turning. Due to these gear motors being at a right angle, you will also be able to track and control the rotation of your wheels! Each gearmotor requires a voltage of 3-6V with a no load current of 200mA while possessing a stall current of 3A@6V (1.5A@3V), a gearbox ratio of 48:1, and a wheel...

These are a pair of hobby gearmotors from DAGU. These gearmotors are the same ones recommended for use in the Shadow Chassis and offer a cheap and easy-to-use setup to get your wheels turning. Each...

These are a pair of hobby gearmotors from DAGU. These gearmotors are the same ones recommended for use in the Shadow Chassis and offer a cheap and easy-to-use setup to get your wheels turning. Each Hobby Gearmotor also possess a 9mm long output on a straight axis. These gearmotors require a voltage of 4.5V with a no load current of 190mA while possessing a gearbox ratio of 48:1 and a wheel speed of 140 RPM unloaded. Every motor order is sold in packs of two. Note: The RPM listed in the...

This is our new Hobby Motor now with a 6mm, 10 tooth, gear to make your basic projects a little simpler to manage. It works well for basic things like making a fan or spinning something pretty fast...

This is our new Hobby Motor now with a 6mm, 10 tooth, gear to make your basic projects a little simpler to manage. It works well for basic things like making a fan or spinning something pretty fast without much resistance. The motor has a normal operating voltage range of 1.0 to 3.0VDC but can handle a max load of up to 12VDC and a no load speed of 6600±10% RPM (@1.0V DC, 110mA). More information is available in the spec sheet linked below. Note: Though the Datasheet for this Hobby Motor...

Humidity and Temperature Sensor - SHT15 BreakoutThis is a simple breakout board for the SHT15 humidity sensor from Sensirion. The SHT15 digital humidity and temperature sensor is fully calibrated...

Humidity and Temperature Sensor - SHT15 BreakoutThis is a simple breakout board for the SHT15 humidity sensor from Sensirion. The SHT15 digital humidity and temperature sensor is fully calibrated and offers high precision and excellent long-term stability at low cost. The digital CMOSens Technology integrates two sensors and readout circuitry on one single chip. These sensors are really impressive! Very sensitive and straight forward to use. Board comes assembled and tested with the SHT15....

Infrared proximity sensor made by Sharp. Part # GP2Y0A21YK has an analog output that varies from 3.1V at 10cm to 0.4V at 80cm. The sensor has a Japanese Solderless Terminal (JST) Connector. We...

Infrared proximity sensor made by Sharp. Part # GP2Y0A21YK has an analog output that varies from 3.1V at 10cm to 0.4V at 80cm. The sensor has a Japanese Solderless Terminal (JST) Connector. We recommend purchasing the related pigtail below or soldering wires directly to the back of the module. Documents: Datasheet Example Code Videos ...

Infrared proximity sensor made by Sharp. Part # GP2Y0A02YK0F has an analog output that varies from 2.8V at 15cm to 0.4V at 150cm with a supply voltage between 4.5 and 5.5VDC. The sensor has a...

Infrared proximity sensor made by Sharp. Part # GP2Y0A02YK0F has an analog output that varies from 2.8V at 15cm to 0.4V at 150cm with a supply voltage between 4.5 and 5.5VDC. The sensor has a Japanese Solderless Terminal (JST) Connector. We recommend purchasing the related pigtail below or soldering wires directly to the back of the module. This sensor is great for sensing objects up to 5 feet away! Documents: Datasheet ...

SMA to MMCX Connector. Adapts MMCX jack to a standard SMA bulkhead. This cable interfaces to the GM862 Cellular modules and the PG31 GPS module. **Length: **6" (6.7" including the MMCX and SMA...

SMA to MMCX Connector. Adapts MMCX jack to a standard SMA bulkhead. This cable interfaces to the GM862 Cellular modules and the PG31 GPS module. **Length: **6" (6.7" including the MMCX and SMA connectors)

This is a 2-pin JST RCY connector typically used for low-voltage applications running 3A or less. They are commonly found in RC vehicles. These come in a bag of 1 male plug, 1 female plug, plus pins...

This is a 2-pin JST RCY connector typically used for low-voltage applications running 3A or less. They are commonly found in RC vehicles. These come in a bag of 1 male plug, 1 female plug, plus pins to connect them both. The pins crimp to your cable and are inserted into the housing. 1 male socket 1 female socket 4 pins Documents: Datasheet ...

This is a simple jumper adapter cable that comes pre-terminated with a female JST connector on one end and a breadboard hookup pigtail on the other. This cable makes it easy to connect components...

This is a simple jumper adapter cable that comes pre-terminated with a female JST connector on one end and a breadboard hookup pigtail on the other. This cable makes it easy to connect components with a JST connector to a breadboard or an Arduino-based device's pins. Wire length is 140mm (about 5.5 inches) long. The adapter's wires have been color coded to Red, Black, and Yellow. Additionally, the female JST connector featuring a basic 2mm pitch while the male hookup pins can easily insert...

This is a simple three wire cable. Great for jumping from board to board or just about anything else. There is a 3-pin JST RE connector on both ends. These are simple jumper wires used on standard...

This is a simple three wire cable. Great for jumping from board to board or just about anything else. There is a 3-pin JST RE connector on both ends. These are simple jumper wires used on standard 0.1" breakaway headers. Features: 12" length Documents: Drawing ...

This is a simple three wire cable. Great for jumping from board to board or just about anything else. There is a 3-pin JST RE connector on both ends. These are simple jumper wires used on standard...

This is a simple three wire cable. Great for jumping from board to board or just about anything else. There is a 3-pin JST RE connector on both ends. These are simple jumper wires used on standard 0.1" breakaway headers. Features: 4" length Documents: Drawing ...

This is a simple four wire cable. Great for jumping from board to board or just about anything else. There is a 4-pin JST RE connector on both ends. These are simple jumper wires used on standard...

This is a simple four wire cable. Great for jumping from board to board or just about anything else. There is a 4-pin JST RE connector on both ends. These are simple jumper wires used on standard 0.1" breakaway headers. Features: 12" length Documents: Drawing ...

This is a simple six wire cable. Great for jumping from board to board or just about anything else. There is a 6-pin JST RE connector on both ends. These are simple jumper wires used on standard...

This is a simple six wire cable. Great for jumping from board to board or just about anything else. There is a 6-pin JST RE connector on both ends. These are simple jumper wires used on standard 0.1" breakaway headers. Features: 4" length Documents: Drawing ...

This is a simple six wire cable. Great for jumping from board to board or just about anything else. There is a 6-pin JST RE connector on both ends. These are simple jumper wires used on standard...

This is a simple six wire cable. Great for jumping from board to board or just about anything else. There is a 6-pin JST RE connector on both ends. These are simple jumper wires used on standard 0.1" breakaway headers. Features: 6" length Documents: Drawing ...

This is a SparkFun exclusive! These are 12" long jumper wires terminated as female to female. Use these to jumper from any male header on any board. Multiple jumpers can be connected next to one...

This is a SparkFun exclusive! These are 12" long jumper wires terminated as female to female. Use these to jumper from any male header on any board. Multiple jumpers can be connected next to one another on a 0.1" header. Comes in one package of ten jumpers (colors shown). We use these wires for everything! They work great with breadboards, Arduinos, and really any 0.1" pitch prototyping board.

This is a SparkFun exclusive! These are 155mm long jumpers with female connectors on both ends. Use these to jumper from any male header on any board, to any other male header. Combine these with...

This is a SparkFun exclusive! These are 155mm long jumpers with female connectors on both ends. Use these to jumper from any male header on any board, to any other male header. Combine these with our male to male jumpers to create a male to female jumper. Multiple jumpers can be installed next to one another on a 0.1" header. Comes as 1 package of ten jumpers (colors shown). Features: 155mm +/-5mm long ...

This Piezo Alarm is a great option for when you need an audible alarm (or are just looking for a way to prank your friends). This alarm has 16 different output options that can be changed with the...

This Piezo Alarm is a great option for when you need an audible alarm (or are just looking for a way to prank your friends). This alarm has 16 different output options that can be changed with the DIP switches on the unit. Select Continuous, Chime, Intermittent, Warble, or Pulsating and amaze your friends. Features: Operating Voltage: 5-16Vdc Operating Frequency: 3KHz Warble Frequency: 2.8KHz to 3.2KHz Diameter: 35.8mm, Height 35.7mm 103 dB(A) at 16V at 61cm 90 dB(A) at 5V at 61cm Documents:...

This shield is specially designed for Micro: bit, LCD1602 and Micro: bit using 4-wire connection, it is the same size as LCD1602 display and has 4 crowtail interface, IIC, UART, analog port and...

This shield is specially designed for Micro: bit, LCD1602 and Micro: bit using 4-wire connection, it is the same size as LCD1602 display and has 4 crowtail interface, IIC, UART, analog port and digital port. LCD1602 display contrast also can be adjusted. Features Apply to Micro: bit. The contrast also can be adjusted. 4-wire communication. Specifications Crowtail interface : IIC, UART, analog port and digital port Output voltage:5v Size: 37mm x 80mm Package list LCD1602 Display for Micro: bit...

LEDs - those blinky things. A must have for power indication, pin status, opto-electronic sensors, and fun blinky displays. This is a very standard red LED. The lens is 3mm in diameter, and is...

LEDs - those blinky things. A must have for power indication, pin status, opto-electronic sensors, and fun blinky displays. This is a very standard red LED. The lens is 3mm in diameter, and is diffused. Features: 1.8-2.2VDC forward drop Max current: 20mA Suggested using current: 16-18mA Luminous Intensity: 150-200mcd Documents: Datasheet LED Tutorial ...

These are very bright LEDs. The LEDs are so bright that it hurts to look directly at them. Please take a look at the pictures to get an idea of the intensity. All lenses are clear. Features:...

These are very bright LEDs. The LEDs are so bright that it hurts to look directly at them. Please take a look at the pictures to get an idea of the intensity. All lenses are clear. Features: Standard size - T1 3/4 5mm 4,000mcd brightness 3.4V forward drop Max current 20mA Documents: Datasheet LED Tutorial ...

These are very bright LEDs. The LEDs are so bright that it hurts to look directly at them. Please take a look at the pictures to get an idea of the intensity. All lenses are clear. Features:...

These are very bright LEDs. The LEDs are so bright that it hurts to look directly at them. Please take a look at the pictures to get an idea of the intensity. All lenses are clear. Features: Standard Size - T1 3/4 5mm Forward Voltage: Min: 3.2V Max: 3.4V Max current 20mA Documents: Datasheet LED Tutorial ...

This is a simple 5mm LED with an interesting array of applications. This UV LED can be used for counterfeit detection (bills, credit cards, documents, etc), sterilization, pesticide, black lights,...

This is a simple 5mm LED with an interesting array of applications. This UV LED can be used for counterfeit detection (bills, credit cards, documents, etc), sterilization, pesticide, black lights, sun burns, the list goes on. Please wear eye protection when using these LEDs. Features: T1 3/4 5mm clear lens 395-400nm 100-180mcd 3-3.6V forward drop Documents: Datasheet LED Tutorial All About LEDs ...

LED Light Bar-GreenDescription: The LED Light Bar is a pre-packaged strip of 3 high-output LEDs powered by 12VDC. We don't have specifics on the output luminocity, but take a look at the example GPS...

LED Light Bar-GreenDescription: The LED Light Bar is a pre-packaged strip of 3 high-output LEDs powered by 12VDC. We don't have specifics on the output luminocity, but take a look at the example GPS Wall Clock project to get an idea. Each unit comes with a fully assembled and tested PCB with current limiting resistors, a wall-mount holder (backed with double-stick tape), and a connection cable. Each LED Light Bar absorbs approximately 30mA @ 12V.Dimensions: 3.08x 0.59" (78x15mm) Mounting hole...

LED Light Bar-RedDescription: The LED Light Baris a pre-packaged strip of 3 high-output LEDs powered by 12VDC. Wedon't have specifics on the output luminocity, but take a look at theexample GPS Wall...

LED Light Bar-RedDescription: The LED Light Baris a pre-packaged strip of 3 high-output LEDs powered by 12VDC. Wedon't have specifics on the output luminocity, but take a look at theexample GPS Wall Clock project to get an idea. Each unit comes with afully assembled and tested PCB with current limiting resistors, a wall-mount holder, and a polarized connectioncable//. Each LED Light Bar absorbs approximately 30mA @ 12V.Dimensions: 3.08x 0.59" (78x15mm)Mounting hole OD is 0.176" (4.5mm)More...

"LED Matrix with dual-color LEDs. This small matrix has both bright-red and bright-green LEDs built into one common cathode housing. Unit comes with a black finish and a opaque LED lenses. The...

"LED Matrix with dual-color LEDs. This small matrix has both bright-red and bright-green LEDs built into one common cathode housing. Unit comes with a black finish and a opaque LED lenses. The picture does not quite do the matrix justice. The Red and Green LEDs are quite clear, and turning both on creates a nice yellow color. Dimensions: 0.275x1.25x1.25" Documents: Datasheet " ...

LED Matrix - Serial Interface - Red/Green/Blue Description: This is a large sized RGB LED Matrix with a backpack that has been designed to take SPI serial input and display any graphics you pass it....

LED Matrix - Serial Interface - Red/Green/Blue Description: This is a large sized RGB LED Matrix with a backpack that has been designed to take SPI serial input and display any graphics you pass it. All the refreshing and communication control is taken care of by the backpack. It's even reprogrammable! 7 software selectable colors are available! Unit comes with a Red/Green/Blue LED Matrix assembled with a RGB Matrix Backpack Controller. Check out the LED Coffee Table tutorial! Documents:...

This is a simple LED-illuminated tactile button with a clear cap. It's just like a basic tactile button, but it lights up blue! So now you can get visual feedback, or light up your project. These...

This is a simple LED-illuminated tactile button with a clear cap. It's just like a basic tactile button, but it lights up blue! So now you can get visual feedback, or light up your project. These have a 12mm body and are rated for 50mA. They don't easily fit into a breadboard, but check below for a breakout board. We also have these in a a variety of colors, check below to see the others. Documents: Datasheet Drawing ...

This is a simple LED-illuminated tactile button with a green cap. It's just like a basic tactile button, but it lights up green! So now you can get visual feedback, or light up your project. These...

This is a simple LED-illuminated tactile button with a green cap. It's just like a basic tactile button, but it lights up green! So now you can get visual feedback, or light up your project. These have a 12mm body and are rated for 50mA. They don't easily fit into a breadboard, but check below for a breakout board. We also have these in a a variety of colors, check below to see the others. Documents: Datasheet Drawing ...

This is a simple LED-illuminated tactile button with a red cap. It's just like a basic tactile button, but it lights up red! So now you can get visual feedback, or light up your project. These have...

This is a simple LED-illuminated tactile button with a red cap. It's just like a basic tactile button, but it lights up red! So now you can get visual feedback, or light up your project. These have a 12mm body and are rated for 50mA. They don't easily fit into a breadboard, but check below for a breakout board. We also have these in a a variety of colors, check below to see the others. Documents: Datasheet Drawing ...

This is a three axis accelerometer for the LilyPad system. Based on the ADXL335 MEMS accelerometer from Analog Devices, the LilyPad Accelerometer can detect joint movement as well as inclination and...

This is a three axis accelerometer for the LilyPad system. Based on the ADXL335 MEMS accelerometer from Analog Devices, the LilyPad Accelerometer can detect joint movement as well as inclination and vibration. The ADXL335 outputs a 0V to 3V analog signal on each of the X, Y, and Z axis. You will need to convert this analog voltage to a gravity amount and use trigonometry to calculate a true 'angle'. If you are not looking for tilt, it is very easy to use this sensor for basic motion...

The LilyPad Arduino 328 Main Board is an Arduino-programmed microcontroller designed to be easily integrated into e-textiles and wearable projects. It offers the same functionality you find in other...

The LilyPad Arduino 328 Main Board is an Arduino-programmed microcontroller designed to be easily integrated into e-textiles and wearable projects. It offers the same functionality you find in other Arduino boards, in a lightweight, round package designed to minimize snagging and profile, with wide tabs that can be sewn down and connected with conductive thread. The LilyPad Arduino consists of an ATmega328 with the Arduino bootloader and a minimum number of external components to keep it as...

We designed this board to give the user a low profile button without any sharp edges. Button closes when you push it and opens when you release (momentary push button). LilyPad is a wearable...

We designed this board to give the user a low profile button without any sharp edges. Button closes when you push it and opens when you release (momentary push button). LilyPad is a wearable e-textile technology developed by Leah Buechley and cooperatively designed by Leah and SparkFun. Each LilyPad was creatively designed to have large connecting pads to allow them to be sewn into clothing. Various input, output, power, and sensor boards are available. They're even washable! Note: A portion...

This is a small buzzer for the LilyPad system. Use 2 I/O pins on the LilyPad main board and create different noises based on the different frequency of I/O toggling. Loud enough to hear inside a...

This is a small buzzer for the LilyPad system. Use 2 I/O pins on the LilyPad main board and create different noises based on the different frequency of I/O toggling. Loud enough to hear inside a pocket but not obtrusively loud. ** Please note:** This is an inductive buzzer meaning that is will act as a short to ground if you are not actively driving it. We recommend you put both I/O pins to low (0V) when the buzzer is not used. Also, it's come to our attention that washing these buzzers will...