Electronics (Kits, Makers, Robotics, Components)

This encoders kit are designed for TT motors. It provides the rotation degree of the wheels. Encoder uses non-contact method to convert the angular displacement signals. Best fit with Micro DC...

This encoders kit are designed for TT motors. It provides the rotation degree of the wheels. Encoder uses non-contact method to convert the angular displacement signals. Best fit with Micro DC Geared Motor.It includes encoders, plastic tube, paper-mediated gasket etc. It uses Gravity interace which is a plug&play design to get connected with Arduino IO Expansion Shield or Raspberry IO Expansion Shield. |Specification| Voltage:+5V Current:&;lt;20mA Resolution:20 PPR Weight:20g|Documents|...

This box of grease is very small, light and easy to carry. It can be uesd in many places. It is suitable for the condition of light load or high speed plastic gear, plastic parts, nylon retainer...

This box of grease is very small, light and easy to carry. It can be uesd in many places. It is suitable for the condition of light load or high speed plastic gear, plastic parts, nylon retainer bearing lubrication, protection and noise reduction. You will need it for your robot and 3D Printer. |Specification| Net Weight : 5g|ShippingList| Grease(5g) x1

Do you need that extra push over the cliff? The Small sized GTE (Goes To Eleven) Knob can fit onto potentiometers with a 6mm wide shaft thanks to a brass insert with a set screw. We know that most...

Do you need that extra push over the cliff? The Small sized GTE (Goes To Eleven) Knob can fit onto potentiometers with a 6mm wide shaft thanks to a brass insert with a set screw. We know that most of you are playing at ten, but with the GTE Knob you can go... one louder. Note: It goes to eleven. Features: 23.6 x 14.2mm Documents: Dimensional Drawing Videos ...

Faster, cheaper, smaller, better, right? The SN754410 Quad Half H-Bridge is just that. Capable of driving high voltage motors using TTL 5V logic levels, the SN754410 can drive 4.5V up to 36V at 1A...

Faster, cheaper, smaller, better, right? The SN754410 Quad Half H-Bridge is just that. Capable of driving high voltage motors using TTL 5V logic levels, the SN754410 can drive 4.5V up to 36V at 1A continuous output current! Please see datasheet for more information. This is a pin to pin compatible replacement for the L293D. **Datasheets: **SN754410

This is the HackRF One, a Software Defined Radio (SDR) peripheral capable of transmission or reception of radio signals from 1MHz to 6GHz. Designed to enable test and development of modern and next...

This is the HackRF One, a Software Defined Radio (SDR) peripheral capable of transmission or reception of radio signals from 1MHz to 6GHz. Designed to enable test and development of modern and next generation radio technologies, HackRF One is an open source hardware platform that can be used as a USB peripheral or programmed for stand-alone operation. If you are wondering what a SDR actually is, it's OK we can help. A Software Defined Radio is essentially a radio communication device that...

    This Hall Sensor Module used Hall Sensor - A3144E. The Hall Sensor measures the Hall Effect, which is a production of a voltage difference across an electrical conductor,...

    This Hall Sensor Module used Hall Sensor - A3144E. The Hall Sensor measures the Hall Effect, which is a production of a voltage difference across an electrical conductor, transverse to an electric current in the conductor as well as a magnetic field perpendicular to the current. The output of the Hall sensor switches low and turns on when a magnetic field perpendicular to the Hall sensor exceeds the BOP threshold, and it switches high and turn on when the magnetic field...

The AH1815 is an integrated Hall-Effect non-latched sensor. That’s nice but what does it do? Holding a magnet near the sensor will cause the output pin to toggle. This makes for a robust presence...

The AH1815 is an integrated Hall-Effect non-latched sensor. That’s nice but what does it do? Holding a magnet near the sensor will cause the output pin to toggle. This makes for a robust presence sensor. A reed sensor also works nicely, but can be limited by the glass encapsulation and size. A Hall-Effect sensor is much smaller, but can handle less current than a reed switch. The AH1815 is a low-sensitivity, micro-power Omnipolar Hall effect switch IC, designed for portable and battery powered...

The US1881 is an integrated Hall-Effect latched sensor. That's nice but what does it do? Holding a magnet near the sensor will cause the output pin to toggle. This makes for a robust presence...

The US1881 is an integrated Hall-Effect latched sensor. That's nice but what does it do? Holding a magnet near the sensor will cause the output pin to toggle. This makes for a robust presence sensor. A reed sensor also works nicely, but can be limited by the glass encapsulation and size. A Hall-Effect sensor is much smaller, but can handle less current than a reed switch. The device includes an on-chip Hall voltage generator for magnetic sensing, a comparator that amplifies the Hall voltage,...

This will be a treat for your ears! The Hamburger Mini Speaker is a 3W economical speaker option for any project needing stand-alone sound. The Hamburger features a built-in lithium polymer battery...

This will be a treat for your ears! The Hamburger Mini Speaker is a 3W economical speaker option for any project needing stand-alone sound. The Hamburger features a built-in lithium polymer battery for portable application, a 3.5mm stereo jack (sorry, iPhone 7 users) and two volume options (quiet and loud) to control how loud your sound needs to be. This speaker really can't be compared to a good pair of JBLs, but for the price point the Hamburger won't break the bank for your next audiophile...

A basic hand held enclosure. Ergonomically designed for hand held comfort. This enclosure is molded in general purpose ABS plastic with soft plastic overmold for comfortable grip. Features: Size /...

A basic hand held enclosure. Ergonomically designed for hand held comfort. This enclosure is molded in general purpose ABS plastic with soft plastic overmold for comfortable grip. Features: Size / Dimensions: 4.615" L x 3.109" W (117.22mm x 78.97mm) Height: 0.945" (24.00mm) Area (L x W): 14.4in² (93cm²) Material: ABS Color: Black Thickness: 0.108" (2.74mm) Material Flammability Rating: UL94 HB Documents: Datasheet ...

HC-07 Serial Bluetooth Module Sometimes you need a cheap and reliable source for communication for your project. With bluetooth you get a virtual wire from your device to your project without the...

HC-07 Serial Bluetooth Module Sometimes you need a cheap and reliable source for communication for your project. With bluetooth you get a virtual wire from your device to your project without the fuss - it just works. Error correction, signal noise and retransmission are all taken care of. Just pair the devices together or to your phone, PC, laptop or controller and you're ready to go. Details: Wireless serial Bluetooth port with jumper wires to make hooking it up even easier. Core...

HC-SR04 Ultrasonic Module Super easy, great price ultrasonic range detection for your project.  Ultrasonic ranging module HC - SR04 provides 2cm - 400cm non-contact measurement...

HC-SR04 Ultrasonic Module Super easy, great price ultrasonic range detection for your project.  Ultrasonic ranging module HC - SR04 provides 2cm - 400cm non-contact measurement function, the ranging accuracy can reach to 3mm. The modules includes ultrasonic transmitters, receiver and control circuit. Specifications: Working Voltage DC 5 V  Working Current 15mA  Max Range 4m  Min Range 2cm  MeasuringAngle 15 degree  Trigger Input Signal 10uS...

HCR (Home Care Robot) with Omni wheels is a full metal open source mobile robot research platform designed for robotics research and service robot application development.Same as previous...

HCR (Home Care Robot) with Omni wheels is a full metal open source mobile robot research platform designed for robotics research and service robot application development.Same as previous generations, the structure of the HCR is divided into 3 layers, each with slots for installing distance sensors, servos or cameras. There is also plenty of space for other expansions modules. More than that, equipped with 3 high torque Omni wheels with encoders, it is capable of all-direction pinpoint...

The HCR Mobile Robot Kit is a two wheel drive mobile robot platform with three levels (if you want, you can use only the parts you need, or make a two level robot). The kit contains two motors, two...

The HCR Mobile Robot Kit is a two wheel drive mobile robot platform with three levels (if you want, you can use only the parts you need, or make a two level robot). The kit contains two motors, two wheels, an omni-directional wheel, and hardware accessories such as metal plates. Its support structure includes servos and sensors, with special interfaces for a mini - ITX motherboard.As the second generation of DFRobot's HCR (Home Care Robot) platform, we have equipped it with new motors and...

The HCR Mobile Robot Kit is a two wheel drive mobile robot platform with three levels (if you want, you can use only the parts you need, or make a two level robot). The mobile robot kit contains two...

The HCR Mobile Robot Kit is a two wheel drive mobile robot platform with three levels (if you want, you can use only the parts you need, or make a two level robot). The mobile robot kit contains two motors, two wheels, an omni-directional wheel, and hardware accessories such as metal plates. Its support structure includes servos and sensors, with special interfaces for a mini - ITX motherboard.As the second generation of DFRobot's HCR (Home Care Robot) platform, we have equipped it with new...

This HDMI connector is specially designed for CrowPi with Raspberry Pi 4B. If you want to upgrade your Crowpi to Raspberry Pi 4B, It is necessary to as a connector. ...

This HDMI connector is specially designed for CrowPi with Raspberry Pi 4B. If you want to upgrade your Crowpi to Raspberry Pi 4B, It is necessary to as a connector.

These are standard 0.1" spaced header pins that can be through-hole mounted. This header connects perfectly with most 10-pin male headers. This is a 10-Pin female header. Documents: Datasheet ...

These are standard 0.1" spaced header pins that can be through-hole mounted. This header connects perfectly with most 10-pin male headers. This is a 10-Pin female header. Documents: Datasheet

These are standard 0.1" spaced header pins that can be surface mounted for applications where through-hole pins won't work. The surface mount side of the legs are staggered for stress relief. This...

These are standard 0.1" spaced header pins that can be surface mounted for applications where through-hole pins won't work. The surface mount side of the legs are staggered for stress relief. This is a 10-Pin male header. Documents: Datasheet

This is a simple 12-pin male PTH straight header. Each pin can even be broken apart if you don't need all 12 pins included with this header. The pins on this header have been spaced at the 0.1"...

This is a simple 12-pin male PTH straight header. Each pin can even be broken apart if you don't need all 12 pins included with this header. The pins on this header have been spaced at the 0.1" standard.

These are standard 0.1" spaced header pins that can be through-hole mounted. This header connects perfectly with most 2-pin male headers. This is a 2-Pin female header. Documents: Drawing ...

These are standard 0.1" spaced header pins that can be through-hole mounted. This header connects perfectly with most 2-pin male headers. This is a 2-Pin female header. Documents: Drawing

This is a 2x23 pin male PTH header. This piece is in the common configuration for Beaglebone Black headers that can be broken apart to form smaller header formations. Each pin has a spacing of 0.1"...

This is a 2x23 pin male PTH header. This piece is in the common configuration for Beaglebone Black headers that can be broken apart to form smaller header formations. Each pin has a spacing of 0.1" in between each other. Documents: Datasheet

This is a simple 2x3 female PTH header. This header is in the common configuration for an ISP connector. Each pin has a spacing of 0.1" in between each other. Documents: Datasheet ...

This is a simple 2x3 female PTH header. This header is in the common configuration for an ISP connector. Each pin has a spacing of 0.1" in between each other. Documents: Datasheet

This is a simple 2x3 male PTH header. This header is in the common configuration for an ISP connector. Each pin has a spacing of 0.1" in between each other. Documents: Datasheet ...

This is a simple 2x3 male PTH header. This header is in the common configuration for an ISP connector. Each pin has a spacing of 0.1" in between each other. Documents: Datasheet

This is a super small, 2x5 pin female PTH header. This header is in the common configuration for JTAG applications. Each pin has a spacing of 1.27mm in between each other. Documents: Datasheet ...

This is a super small, 2x5 pin female PTH header. This header is in the common configuration for JTAG applications. Each pin has a spacing of 1.27mm in between each other. Documents: Datasheet

This is a super small, 2x5 pin male PTH header. This header is in the common configuration for JTAG applications. Each pin has a spacing of 1.27mm in between each other and can be cut down to...

This is a super small, 2x5 pin male PTH header. This header is in the common configuration for JTAG applications. Each pin has a spacing of 1.27mm in between each other and can be cut down to smaller increments if the need arises. Features: Pin style: square Number of pins: 10 (2x5) Pin spacing: 1.27mm (0.05") Documents: Datasheet ...

This is a 2x5 pin 1.27mm header. Documents: Mechanical Drawing

This is a 2x5 pin 1.27mm header. Documents: Mechanical Drawing

This is a simple 2x6 female PTH header. Each pin has a spacing of 0.1" in between each other. Documents: Datasheet ...

This is a simple 2x6 female PTH header. Each pin has a spacing of 0.1" in between each other. Documents: Datasheet

This is a simple 2x8 male PTH header. This header is that you will find commonly used to interface with a basic 8x2 character LCDs. Each pin has a spacing of 0.1" in between each other. Documents:...

This is a simple 2x8 male PTH header. This header is that you will find commonly used to interface with a basic 8x2 character LCDs. Each pin has a spacing of 0.1" in between each other. Documents: Datasheet

This is a simple 3-pin male PTH right angle header. Each pin can even be broken apart if you only need one or two pins instead of all three. The pins on this header have been spaced at the 0.1"...

This is a simple 3-pin male PTH right angle header. Each pin can even be broken apart if you only need one or two pins instead of all three. The pins on this header have been spaced at the 0.1" standard.

This is a SMD 4-pin right angle male header. We use this header on our Graphic LCD Serial Backpack. Pins have 0.1" spacing between rows and between pins. Documents: Dimensional Drawing ...

This is a SMD 4-pin right angle male header. We use this header on our Graphic LCD Serial Backpack. Pins have 0.1" spacing between rows and between pins. Documents: Dimensional Drawing

These are standard 0.1" spaced header pins that can be through-hole mounted. This header connects perfectly with most 5-pin male headers. This is a 5-Pin female header. Documents: Drawing ...

These are standard 0.1" spaced header pins that can be through-hole mounted. This header connects perfectly with most 5-pin male headers. This is a 5-Pin female header. Documents: Drawing

These are standard 0.1" spaced header pins that can be through-hole mounted. This header connects perfectly with most 6-pin male headers. This is a 6-Pin female header. Documents: Datasheet ...

These are standard 0.1" spaced header pins that can be through-hole mounted. This header connects perfectly with most 6-pin male headers. This is a 6-Pin female header. Documents: Datasheet

These are standard 0.1" spaced header pins that can be surface mounted for applications where through-hole pins won't work. The surface mount side of the legs are staggered for stress relief. This...

These are standard 0.1" spaced header pins that can be surface mounted for applications where through-hole pins won't work. The surface mount side of the legs are staggered for stress relief. This is a 6-Pin female header. Documents: Datasheet

This is a SMD 6 pin right angle female header. We realized that we have had the male version of this header available for awhile now, but never the female. Now you have the ability to get both! Pins...

This is a SMD 6 pin right angle female header. We realized that we have had the male version of this header available for awhile now, but never the female. Now you have the ability to get both! Pins have 0.1" spacing between rows and between pins. Documents: Dimensional Drawing

These are standard 0.1" spaced header pins that can be surface mounted for applications where through-hole pins won't work. The surface mount side of the legs are staggered for stress relief. This...

These are standard 0.1" spaced header pins that can be surface mounted for applications where through-hole pins won't work. The surface mount side of the legs are staggered for stress relief. This is a 6-Pin male header. Documents: Datasheet

This is a SMD 6 pin right angle male header. We use this header on our LilyPad Main Board. Pins have 0.1" spacing between rows and between pins. Documents: Dimensional Drawing ...

This is a SMD 6 pin right angle male header. We use this header on our LilyPad Main Board. Pins have 0.1" spacing between rows and between pins. Documents: Dimensional Drawing

These are standard 0.1" spaced header pins that can be through-hole mounted. This header connects perfectly with most 8-pin male headers. This is a 8-Pin female header. Documents: Datasheet ...

These are standard 0.1" spaced header pins that can be through-hole mounted. This header connects perfectly with most 8-pin male headers. This is a 8-Pin female header. Documents: Datasheet

These are standard 0.1" spaced header pins that can be surface mounted for applications where through-hole pins won't work. The surface mount side of the legs are staggered for stress relief. This...

These are standard 0.1" spaced header pins that can be surface mounted for applications where through-hole pins won't work. The surface mount side of the legs are staggered for stress relief. This is an 8-Pin female header. Documents: Datasheet

These are standard 0.1" spaced header pins that can be surface mounted for applications where through-hole pins won't work. The surface mount side of the legs are staggered for stress relief. This...

These are standard 0.1" spaced header pins that can be surface mounted for applications where through-hole pins won't work. The surface mount side of the legs are staggered for stress relief. This is an 8-Pin male header. Documents: Datasheet

Be still my beating heart! With the heART Surface Mount Soldering Kit you will be able to learn the basics of SMD soldering by being able to assemble a beating heart pendant! Each heART kit takes...

Be still my beating heart! With the heART Surface Mount Soldering Kit you will be able to learn the basics of SMD soldering by being able to assemble a beating heart pendant! Each heART kit takes about 20-40min to assemble depending on your soldering skill level with basic soldering materials (not included). This little kit provides a great learning tool to help you practice and improve your overall soldering skills without proving to be an impossible challenge! Every heART pendant kit...

We love heat shrink! We use it for all sorts of handy projects. Use it to reinforce connections, protect devices, and electrically isolate exposed solder joints. We worked with a manufacturer to...

We love heat shrink! We use it for all sorts of handy projects. Use it to reinforce connections, protect devices, and electrically isolate exposed solder joints. We worked with a manufacturer to create a kit that we would use: lots of colors, lots of sizes, nothing too long. We specially requested some of the sizes with heat sensitive glue which significantly increases stress relief and water proofing. This kit includes 95 pieces of heat shrink, all of varying colors and sizes, and comes in a...

These DC powered heating pads are perfect for near-body heating applications. They get warm to the touch but not too hot as long as you provide the appropriate voltage. Simply apply 5VDC to the wire...

These DC powered heating pads are perfect for near-body heating applications. They get warm to the touch but not too hot as long as you provide the appropriate voltage. Simply apply 5VDC to the wire leads and within minutes, the pad will begin to warm up. These heating pads are constructed using a mesh of Polyester filament and Micro Metal Conductive Fiber folded into a protective Polyimide Film. The fact that these are low power, flexible and draw little power makes them ideal for things like...

These DC powered heating pads are perfect for near-body heating applications. They get warm to the touch but not too hot as long as you provide the appropriate voltage. Simply apply 5VDC to the wire...

These DC powered heating pads are perfect for near-body heating applications. They get warm to the touch but not too hot as long as you provide the appropriate voltage. Simply apply 5VDC to the wire leads and within minutes, the pad will begin to warm up. These heating pads are constructed using a mesh of Polyester filament and Micro Metal Conductive Fiber folded into a protective Polyimide Film. The fact that these are low power, flexible and draw little power makes them ideal for things like...

A 13.20 x 12.10 mm self-adhesive pure copper heatsink designed to dissipate heat away from your boards and ICs. Features: Material: Copper Length: 13.20 mm Width: 12.10 mm Self-Adhesive ...

A 13.20 x 12.10 mm self-adhesive pure copper heatsink designed to dissipate heat away from your boards and ICs. Features: Material: Copper Length: 13.20 mm Width: 12.10 mm Self-Adhesive

This is a 5g syringe of white heatsink compound (aka thermal grease, thermal paste, thermal goo). Use this whenever you're connecting a component to a heatsink, it'll really help to dissipate even...

This is a 5g syringe of white heatsink compound (aka thermal grease, thermal paste, thermal goo). Use this whenever you're connecting a component to a heatsink, it'll really help to dissipate even more potentially damaging heat. This compound is composed of 50% silicone, 20% carbon, and 30% metal oxide. It has a thermal conductivity of 1.172 W/(mK), which should be plenty for voltage regulators, MOSFETs, motor drivers, audio amplifiers, etc. Features: Color: White Thermal Conductivity: 1.172...

Small heat sink for TO-220 components. Ideal for keeping your 5V and 3.3V regulators running cool. Black anodized bolt on type with 2.5W dissipation.

Small heat sink for TO-220 components. Ideal for keeping your 5V and 3.3V regulators running cool. Black anodized bolt on type with 2.5W dissipation.

μHex is the first low-power controller which is compatible with Arduino. It is very suitable for the battery power supply environment. A 210mAh CR2032 cell battery could make it work 60 days...

μHex is the first low-power controller which is compatible with Arduino. It is very suitable for the battery power supply environment. A 210mAh CR2032 cell battery could make it work 60 days long.As it is using Atmega 328 Microcontroller, it has good general and powerful performance. It packs 14 GPIO and 7 power ports (4 of them could be controlled) which could suit most of your project requirements.Designed by maker Leo Yan.Note: Bootloader is write protected, please do not attempt to...

These aluminum hex standoffs are 0.750in. (19.05mm) 3/4in. long and tapped for a 4-40 screw. These are great for mounting your board in an enclosure, or just getting it up off the table. Sold...

These aluminum hex standoffs are 0.750in. (19.05mm) 3/4in. long and tapped for a 4-40 screw. These are great for mounting your board in an enclosure, or just getting it up off the table. Sold individually. Features: Screw, Thread Size: #4-40 Diameter - Outside: 0.250" (6.35mm) 1/4" Hex Between Board Height: 0.750" (19.05mm) 3/4" Length - Overall: 0.938" (23.83mm) 15/16" Material: Aluminum Plating: Iridite ...

These aluminum hex standoffs are 2.375in. (60.33mm) long and tapped for a 4-40 screw. These are great for mounting your board in an enclosure, or just getting it up off the table. Sold individually....

These aluminum hex standoffs are 2.375in. (60.33mm) long and tapped for a 4-40 screw. These are great for mounting your board in an enclosure, or just getting it up off the table. Sold individually. Features: Screw, Thread Size: #4-40 Diameter - Outside: 0.250" (6.35mm) 1/4" Hex Between Board Height: 2.375" (60.33mm) 2 3/8" Length - Overall: 2.375" (60.33mm) 2 3/8"

The Hexa Base Rotate Kit is perfect for rotating a large mass. It can easily support 10lbs of weight.It's injection molded from ultra strong ABS plastic.This HEXA Base Rotate Kit is compatible with...

The Hexa Base Rotate Kit is perfect for rotating a large mass. It can easily support 10lbs of weight.It's injection molded from ultra strong ABS plastic.This HEXA Base Rotate Kit is compatible with a majority of servo products sold on market. It also works perfectly with FIT0004 Pan and Tilt Kit (Black Anodized) and FIT0038 Aluminum Multi-Purpose Servo Bracket for the robotic arm.With its unique hexagonal design, users can pile mutliple turntables in a row or make a real "Hive".The kit comes...

With this high-strength, acrylic gasket, you will be able to attach the 0.3W panels (0.3 Watt, 2 Volt and 0.3 Watt, 6 Volt) to an enclosure or almost any other flat surface. The gasket creates a...

With this high-strength, acrylic gasket, you will be able to attach the 0.3W panels (0.3 Watt, 2 Volt and 0.3 Watt, 6 Volt) to an enclosure or almost any other flat surface. The gasket creates a waterproof and secure connection between the panel and a wide variety of materials including plastic and aluminum. For best results, clean both surfaces with isopropyl alcohol and apply with approximately 14PSI. Features: 3M VHB Creates Waterproof and Secure Seal (when properly applied) Dimensions: 47...

With this high-strength, acrylic gasket, you will be able to attach the 1.2W panels (P124) to an enclosure or almost any other flat surface. The gasket creates a waterproof and secure connection...

With this high-strength, acrylic gasket, you will be able to attach the 1.2W panels (P124) to an enclosure or almost any other flat surface. The gasket creates a waterproof and secure connection between the panel and a wide variety of materials including plastic and aluminum. For best results, clean both surfaces with isopropyl alcohol and apply with approximately 14PSI. Features: 3M VHB Creates Waterproof and Secure Seal (when properly applied) Dimensions: 66 x 113 x 1.1mm Compatible with...

This High Speed HDMI Cable provides a one-cable solution for many of your home entertainment needs. As a versatile HDMI cable, it provides high-definition quality for not only home entertainment...

This High Speed HDMI Cable provides a one-cable solution for many of your home entertainment needs. As a versatile HDMI cable, it provides high-definition quality for not only home entertainment networking, but also mini PCs such as Raspberry Pi, Cubieboard, PCduino, etc. The gold plated surface also ensures long term endurability. You can use this cable to connect your devices with your Apple TV ,Mac mini, cable box, satellite dish, Blu-ray Disc player, Laptop, PC, and enjoy quality audio and...

This High Speed HDMI Cable provides a one-cable solution for your home entertainment needs. As a versatile HDMI cable, it provides high-definition quality for not only LattePanda, but also home...

This High Speed HDMI Cable provides a one-cable solution for your home entertainment needs. As a versatile HDMI cable, it provides high-definition quality for not only LattePanda, but also home entertainment networking or mini PCs such as Raspberry Pi, Cubieboard, PCduino, etc. The gold plated surface ensures excellent signal and durability. You can use this cable to connect your devices with your Apple TV, Mac mini, cable box, satellite dish, Blu-ray Disc player, Laptop, PC, and enjoy quality...

This diode-transistor photocouplers consist of an LED, optically coupled to a high speed photodetector to transmit electrical signals between circuits while still isolating your system from higher...

This diode-transistor photocouplers consist of an LED, optically coupled to a high speed photodetector to transmit electrical signals between circuits while still isolating your system from higher voltages. The 6N137 optoisolator is presented in an 8-pin DIP package. The output features is an open collector and coupler parameters are guaranteed over the temperature range from -40℃~5℃. The internal shield provides a guaranteed Common Mode Transient Immunity (typical) 10KV/μs. Features: High...

This is a 33 meter roll of polyimide tape. This tape is a fantastic insulator, like electrical tape, but it can withstand temperatures as high as 258°C (496°F). It also provides good resistance to...

This is a 33 meter roll of polyimide tape. This tape is a fantastic insulator, like electrical tape, but it can withstand temperatures as high as 258°C (496°F). It also provides good resistance to corrosion and the silicone adhesive holds tight throughout the tape's rated temperature range. This is a good choice for insulating components inside of an enclosure that might be subjected to extreme conditions. Documents: Datasheet ...

The HM01B0 from Himax Imaging is an ultra low power CMOS Image Sensor that enables the integration of an “Always On” camera for computer vision applications such as gestures, intelligent ambient...

The HM01B0 from Himax Imaging is an ultra low power CMOS Image Sensor that enables the integration of an “Always On” camera for computer vision applications such as gestures, intelligent ambient light and proximity sensing, tracking and object identification. The sensor allows the sensor to consume very low power of SparkFun Edge Development Board and comes with a ribbon cable that mates to the camera connector populated on the Edge board. The HM01B0 contains 320 x 320 pixel resolution and...

The Himax WE-I Plus EVB Endpoint AI Development Board is the perfect solution for just that; a computer/machine vision or AI endpoint. In collaboration with Google TensorFlow Lite for...

The Himax WE-I Plus EVB Endpoint AI Development Board is the perfect solution for just that; a computer/machine vision or AI endpoint. In collaboration with Google TensorFlow Lite for Microcontrollers framework and Synopsys embARC MLI library, the Himax WE-I Plus EVB provides a complete development environment to deploy all TensorFlow Lite for Microcontrollers examples; “Person detection”, “Micro speech”, and “Magic wand”, for “Vision”, “Voice” and “Vibration” applications. The WE-I Plus EVB...

The Hinj development board uses an Intel MAX 10 FPGA along with multiple connectivity options to create an all-in-one IoT/Smart Automation development solution. With Modular compatibility for...

The Hinj development board uses an Intel MAX 10 FPGA along with multiple connectivity options to create an all-in-one IoT/Smart Automation development solution. With Modular compatibility for Arduino, Digilent Pmod, and Digi XBee it is easy to migrate previous designs or projects to the FPGA. On-board WiFi and Ethernet makes connecting your project simple as well. Includes: Hinj Development Board USB Cable Power Adapter Features: Intel MAX 10 FPGA (50K LE) Embedded 8-bit Microcontroller AVR...

The HS-311 is the perfect servo for inexpensive applications. Do not let the price fool you though, this servo features many of the same aspects of more expensive servos. One peice circuit board and...

The HS-311 is the perfect servo for inexpensive applications. Do not let the price fool you though, this servo features many of the same aspects of more expensive servos. One peice circuit board and tight mesh gears ensures great durability. Comes with a number of various servo horns and arms with mounting hardware.This servo can operate 180° when given a pulse signal ranging from 600usec to 2400usec.|Specification| Speed: 0.19 sec/60° at 4.8V Speed: 0.15 sec/60° at 6.0V Torque:...

These are a pair of right angle, hobby gearmotors from DAGU. These gearmotors are the same ones utilized in the Magician Chassis and RedBot Kit and offer a cheap and easy to use setup to get your...

These are a pair of right angle, hobby gearmotors from DAGU. These gearmotors are the same ones utilized in the Magician Chassis and RedBot Kit and offer a cheap and easy to use setup to get your wheels turning. Due to these gear motors being at a right angle, you will also be able to track and control the rotation of your wheels! Each gearmotor requires a voltage of 3-6V with a no load current of 200mA while possessing a stall current of 3A@6V (1.5A@3V), a gearbox ratio of 48:1, and a wheel...

These are a pair of hobby gearmotors from DAGU. These gearmotors are the same ones recommended for use in the Shadow Chassis and offer a cheap and easy-to-use setup to get your wheels turning. Each...

These are a pair of hobby gearmotors from DAGU. These gearmotors are the same ones recommended for use in the Shadow Chassis and offer a cheap and easy-to-use setup to get your wheels turning. Each Hobby Gearmotor also possess a 9mm long output on a straight axis. These gearmotors require a voltage of 4.5V with a no load current of 190mA while possessing a gearbox ratio of 48:1 and a wheel speed of 140 RPM unloaded. Every motor order is sold in packs of two. Note: The RPM listed in the...

This is a hobby gearmotor from DAGU. These gearmotors are the same ones recommended for use in the Shadow Chassis and offer a cheap and easy-to-use setup to get your wheels turning. Each Hobby...

This is a hobby gearmotor from DAGU. These gearmotors are the same ones recommended for use in the Shadow Chassis and offer a cheap and easy-to-use setup to get your wheels turning. Each Hobby Gearmotor also possess a 9mm long output on a straight axis. These gearmotors require a voltage of 4.5V with a no load current of 190mA while possessing a gearbox ratio of 48:1 and a wheel speed of 140 RPM unloaded. Features: Suggested Voltage: 4.5VDC No Load Speed: 140RPM No Load Current: 190mA Max....

It's like an Xacto knife, only better. We use these extensively when working with PCBs. These small knives work well for cutting traces, scraping ground pours, and guiding hair-like wires into their...

It's like an Xacto knife, only better. We use these extensively when working with PCBs. These small knives work well for cutting traces, scraping ground pours, and guiding hair-like wires into their proper place. Excel knife comes with aluminum handle, one ultra-sharp blade, and safety cap.