Products 1-48 of 172
Show
Atto84 with Arduino Bootloader
OOD!
Price: $13.71
View
Availability: Back Order
Sparkfun Item #: SPX-14804 -

Arduino and Arduino compatible dev boards are an awesome tool for developing an idea quickly but, being development boards, they're often a little more bulky and full featured than you really need. Having a USB interface and a bootloader is so nice, though, so we put together the bare minimum Arduino compatible breakout for integration into your small projects. We call it the Atto84. The Atto84 is essentially a breakout board for the absolutely minute WQFN ATtiny84, but we've done some work to...

Big Easy Driver
Price: $36.02
View
Availability: Stocked
Sparkfun Item #: ROB-12859 -

The Big Easy Driver, designed by Brian Schmalz, is a stepper motor driver board for bi-polar stepper motors up to a max 2A/phase. It is based on the Allegro A4988 stepper driver chip. It's the next version of the popular Easy Driver board. Each Big Easy Driver can drive up to a max of 2A per phase of a bi-polar stepper motor. It is a chopper microstepping driver which defaults to 16 step microstepping mode. It can take a maximum motor drive voltage of around 30V, and includes on-board 5V/3.3V...

Bus Pirate - v3.6a
OOD!
Price: $53.09
View
Availability: Back Order
Sparkfun Item #: TOL-12942 -

The Bus Pirate v3.6a, created by Ian Lesnet, is a troubleshooting tool that communicates between a PC and any embedded device over 1-wire, 2-wire, 3-wire, UART, I2C, SPI, and HD44780 LCD protocols - all at voltages from 0-5.5VDC. This product eliminates a ton of early prototyping effort when working with new or unknown chips. Working with the Bus Pirate is simple and effective - type commands into a terminal on your computer, those commands are interpreted by the Bus Pirate and sent via the...

Button Pad 2x2 - Breakout PCB
OOD!
Price: $8.77
View
Availability: Back Order
Sparkfun Item #: COM-09277 -

This a simple breakout board for the button pads. Each LED and button is brought out to the side connectors. The connectors are soldered to the back side of the PCB. We recommend trimming the connector leads on the button side as short as possible to reduce the deflection of the pad. Now with footprints for diodes! Use the super cheap 1N4148 through-hole diodes. These can be used to isolate the switches to make for a bit easier decoding. Documents: Schematic Eagle Files ...

Button Pad 4x4 - Breakout PCB
Price: $17.96
View
Availability: Stocked
Sparkfun Item #: COM-08033 -

This a simple breakout board for the button pads. Each LED and button is brought out to the side connectors. The connectors are soldered to the back side of the PCB. We recommend trimming the connector leads on the button side as short as possible to reduce the deflection of the pad. Now with footprints for diodes! Use the super cheap 1N4148 through-hole diodes. These can be used to isolate the switches to make for a bit easier decoding. Documents: Schematic Eagle Files Hookup Guide Datasheet...

Button Pad 4x4 - LED Compatible
OOD!
Price: $9.31
View
Availability: Back Order
Sparkfun Item #: COM-07835 -

This is a translucent silicon rubber button pad with 16 buttons originally inspired by the folks at monome.org. Each button has a hole underneath that accepts either a 3mm or 5mm standard LED. The idea is that you can create a button interface of your choice with the ability to display simple colors under each button. Mainly, we wanted to use our tri-color LEDs to create a full RGB color for each button. 16 button pad can be split up into four, 4 button pads. Each button has a conductive...

Cherry MX Switch Breakout
Price: $3.52
View
Availability: Stocked
Sparkfun Item #: BOB-13773 -

Cherry MX Keyswitches are top-of-the-line mechanical keyboard switches. They’re satisfyingly “clicky”, reliable up to tens-of-millions of key presses, and a standard in gaming and programming keyboards across the globe. With the SparkFun Cherry MX Switch Breakout we have made the switches more easily adaptable to breadboard or perfboard-based projects. The Cherry MX Switch Breakout is a perfect prototyping tool for projects ranging from a single-key user-input to fully-custom 101-key...

EasyDriver - Stepper Motor Driver
Price: $26.99
View
Availability: Stocked
Sparkfun Item #: ROB-12779 -

The EasyDriver is a simple to use stepper motor driver, compatible with anything that can output a digital 0 to 5V pulse (or 0 to 3.3V pulse if you solder SJ2 closed on the EasyDriver). The EasyDriver requires a 6V to 30V supply to power the motor and can power any voltage of stepper motor. The EasyDriver has an on board voltage regulator for the digital interface that can be set to 5V or 3.3V. Connect a 4-wire stepper motor and a microcontroller and you've got precision motor control!...

FemtoBuck LED Driver
Price: $14.09
View
Availability: Out of Stock
Sparkfun Item #: COM-13716 -

This is the FemtoBuck, a small-size single-output constant current LED driver. Each FemtoBuck has the capability to dim a single high-power channel of LEDs from 0-350mA at up to 36V while the dimming control can be either accessed via PWM or analog signal from 0-2.5V. This board is based off of the PicoBuck LED Driver, developed in collaboration with Ethan Zonca, except instead of blending three different LEDs on three different channels the FemtoBuck controls just one. For the FemtoBuck,...

LED Tactile Button Breakout
OOD!
Price: $2.66
View
Availability: Back Order
Sparkfun Item #: BOB-10467 -

This simple breakout board makes it easy to use our LED tactile switches in a breadboard, or your next project. Note: Populate the board according to the polarity of the LED on the switch. The markings for the switch are irrelevant and can be reversed. Documents: Schematic Eagle Files GitHub ...

MP3 Trigger
Price: $90.19
View
Availability: Stocked
Sparkfun Item #: WIG-13720 -

Make some noise with your next project! The MP3 Trigger board is built to make MP3 sound integration easier than ever. The board has 18 external trigger pins that will directly trigger pre-selected MP3 tracks, and a full-duplex serial control port that provides full transport control, remote triggering for up to 256 tracks, and fast real-time volume control. MP3s are stored on FAT16 formatted SDSC or FAT32 formatted SDHC micro-SD flash memory cards. In addition, optimized code can achieve...

PicoBuck LED Driver
OOD!
Price: $28.27
View
Availability: Back Order
Sparkfun Item #: COM-13705 -

The PicoBuck LED Driver is an economical and easy to use driver that will allow you to control and blend three different LEDs on three different channels. By default, each channel is driven at 330mA; that current can be reduced by either presenting an analog voltage or a PWM signal to the board. Version 12 of the board adds a solderable jumper that can be closed to increase the maximum current to 660mA. The new voltage regulator also increased the voltage rating on the various components on...

Qwiic Iridium 9603N
OOD!
Price: $553.80
View
Availability: Back Order
Sparkfun Item #: SPX-16394 -

With a clear view of the sky, the Qwiic Iridium 9603 allows you to send and receive short messages. It works anywhere in the world, far beyond the reach of WiFi and GSM networks. Maybe you want to transmit weather information from a weather station on top of a mountain? Or use it to send data from a travelling balloon sat? Perhaps you need to communicate in an emergency, when other networks might not be available? At the heart of our product is an Iridium 9603 modem. The Qwiic module hosts the...

Qwiic LED Stick
OOD!
Price: $22.93
View
Availability: Back Order
Sparkfun Item #: SPX-14783 -

The Qwiic LED Stick features ten addressable APA102 LEDs, making it easy to add full color LED control using I2C. Write to individual LEDs to display a count in binary, or write to the whole strip for cool lighting effects. You can even add more LEDs to the end if you need to1. We’ve written an Arduino library that takes care of the I2C and communication to the LEDs so all you have to do is decide what color each LED should be. The LED Stick has a default I2C address of 0x23 but can be changed...

RGB Sensor (Qwiic) - BH1749NUC
OOD!
Price: $22.93
View
Availability: Back Order
Sparkfun Item #: SPX-14733 -

Need to autonomously monitor for that specific color value? Want to hone in on that magenta ball? Or follow that aquamarine line? The BH1749NUC-based Qwiic RGB Sensor is here for all of your red, green, blue, and infrared color-sensing needs. The BH1749NUC features an I2C interface and a programmable interrupt output. It senses red, green, blue, and infrared in its field-of-view, then reports each channel as a 16-bit value. Additionally, it features programmable IR and RGB gains and a variable...

SD Sniffer
OOD!
Price: $19.41
View
Availability: Back Order
Sparkfun Item #: TOL-11468 -

This board is a unique board recommended by a SparkFun customer. When playing with SD, you sometimes need to view what the SPI traffic is doing, whether for hacking or debugging. The SD Sniffer allows you to hook up an external device, such as a logic analyzer or microcontroller, to view what signals are being passed back and forth. Insert one side into a regular SD socket and a SD card into the SD holder, simple as that. **Note: **This product is a collaboration and a portion of each sale...

SparkFun 16 Output I/O Expander Breakout - SX1509
OOD!
Price: $11.30
View
Availability: Back Order
Sparkfun Item #: BOB-13601 -

Are you low on I/O? No problem! The SX1509 Breakout is a 16-channel GPIO expander with an I2C interface – that means with just two wires, your microcontroller can interface with 16 fully configurable digital input/output pins. But the SX1509 can do so much more than just simple digital pin control. It can produce PWM signals, so you can dim LEDs. It can be set to blink or even breathe pins at varying rates. This breakout is similar to a multiplexer or "mux," in that it allows you to get more...

SparkFun Adjustable LiPo Charger
Price: $21.18
View
Availability: Out of Stock
Sparkfun Item #: PRT-14380 -

The SparkFun Adjustable LiPo Charger is a single-cell lithium polymer (LiPo) and lithium ion battery charger. Because it’s adjustable, this charger will be able to safely charge most of our single-cell batteries with ease. With its onboard charge rate selector, you will be able to set the maximum amount of current to charge your battery from 15mA to 500mA. Once the board is configured for the battery, you can connect power from either a microUSB cable or the pins below the USB connector...

SparkFun Analog/Digital MUX Breakout - CD74HC4067
OOD!
Price: $10.63
View
Availability: Back Order
Sparkfun Item #: BOB-09056 -

This is a breakout board for the very handy 16-Channel Analog/Digital Multiplexer/Demultiplexer CD74HC4067. This chip is like a rotary switch - it internally routes the common pin (COM in the schematic, SIG on the board) to one of 16 channel pins (CHANxx). It works with both digital and analog signals (the voltage can't be higher than VCC), and the connections function in either direction. To control it, connect 4 digital outputs to the chip's address select pins (S0-S3), and send it the...

SparkFun ATX Power Connector Breakout Board
OOD!
Price: $3.46
View
Availability: Back Order
Sparkfun Item #: BOB-15035 -

Do you need to power a project with 12V and 5V from one power supply? The ATX power connector breakout board breaks out the standard 4-pin computer peripheral port when mated with an ATX connector for your 12V and 5V devices! Once you have chosen a power supply (whether it be an ATX power supply or the 12V/5V wall adapter), you're ready to give your project some life! This board will need additional parts including a 12V/5V power supply, an ATX breakout, and screw terminals to power your...

SparkFun AutoDriver - Stepper Motor Driver (v13)
OOD!
Price: $69.04
View
Availability: Back Order
Sparkfun Item #: BOB-13752 -

The SparkFun AutoDriver board is based on the STMicro L6470 dSPIN stepper motor driver. This powerful chip allows you to control a stepper motor with a voltage from 8 to 45V at 3Arms over an SPI connection. The AutoDriver board has been designed to be easily integrated into a project, even with multiple boards. Just connect your motors and your SPI-capable microcontroller and get steppin'! STMicro's L6470 is a 3A, 8--45V bipolar stepper motor driver. It has built-in overcurrent detection,...

SparkFun Battery Babysitter - LiPo Battery Manager
Price: $35.36
View
Availability: Out of Stock
Sparkfun Item #: PRT-13777 -

The SparkFun Battery Babysitter is an all-in-one single-cell Lithium Polymer (LiPo) battery manager. It’s half battery charger, half battery monitor, and all you’ll ever need to keep your battery-powered project running safely and extensively. The Battery Babysitter features a pair of Texas Instruments LiPo-management ICs: a BQ24075 battery charger and a BQ27441-G1A fuel gauge. The charger supports adjustable charge rates of up to 1.5A, as well as USB-compliant 100mA and 500mA options. It also...

SparkFun Big Red Box Proto Board
OOD!
Price: $14.09
View
Availability: Back Order
Sparkfun Item #: DEV-13317 -

The SparkFun Big Red Box Proto Board is a large, custom made PCB that has been specifically designed to be used with and installed into our Big Red Box. This board features a large prototyping area with exactly 1,488 solder points (yes, we counted). With this proto board you will be able to create or incorporate unique projects into a reliably weatherproof enclosure. Each SparkFun Big Red Box Proto Board is equipped with ten mounting holes to secure it inside the enclosure. The proto board can...

SparkFun Breadboard Power Supply Stick - 3.3V/1.8V
Price: $30.04
View
Availability: Out of Stock
Sparkfun Item #: PRT-13157 -

This is a very simple board that takes a 4-9V input voltage and outputs a selectable 1.8V or 3.3V regulated voltage. All headers are 0.1" pitch for simple insertion into a breadboard. Input power can be supplied to either the DC barrel jack or the two pin header labeled + and -. Output power is supplied to the pins labeled GND and VCC. Board has both an On/Off switch and a voltage select switch (3.3V/1.8V). The two sets of four GND and VCC pins are spaced such that when connected to our Basic...

SparkFun Breadboard Power Supply Stick - 5V/3.3V
OOD!
Price: $21.18
View
Availability: Back Order
Sparkfun Item #: PRT-13032 -

This is a very simple board that takes a 6-12V input voltage and outputs a selectable 5V or 3.3V regulated voltage. All headers are 0.1" pitch for simple insertion into a breadboard. Input power can be supplied to either the DC barrel jack or the two pin header labeled + and -. Output power is supplied to the pins labeled GND and VCC. Board has both an On/Off switch and a voltage select switch (3.3V/5V). The two sets of four GND and VCC holes are spaced such that when connected to our Basic...

SparkFun Buck-Boost Converter
OOD!
Price: $19.01
View
Availability: Back Order
Sparkfun Item #: COM-15208 -

The SparkFun Buck-Boost Converter is a handy power accessory board that allows you to fine tune the amount of power your project receives. This converter can take an input voltage of anywhere from 3-16V which can then be regulated to an output voltage between 2.5-9V. With the switch on the bottom of the board, you can set the common output voltages of 3.3V and 5V, but we've also added a custom setting that allows you to solder a resistor based on your custom voltage needs. The GPIO pins have...

SparkFun Clock Generator Breakout - 5P49V60 (Qwiic)
OOD!
Price: $53.09
View
Availability: Back Order
Sparkfun Item #: BOB-15734 -

The SparkFun Qwiic Clock Generator Breakout offers a wide range of customizable frequencies in a wide range of different signal types using a single reference clock. Four (single output) clock outputs can generate frequencies from 1MHz-200MHz and eight (differential output) clock outputs can generate frequencies from 1MHz-350MHz. The frequency's many properties can be manipulated in code via I2C using the SparkFun Arduino Library. There are two Qwiic connectors populated on the board to easily...

SparkFun Configurable OpAmp Board - TSH82
OOD!
Price: $8.77
View
Availability: Back Order
Sparkfun Item #: BOB-14874 -

The SparkFun TSH82 Configurable OpAmp Board was designed to give you the best combination of performance and flexibility that we could achieve by giving you two gain stages, each one independently accessible on the header pins. Each stage is natively configured as an inverting amplifier that can also be strung together to expand the capabilities of the OpAmp. With the use of the jumpers on the back of the board, you can configure each stage for non-inverting operation, differential input, and...

SparkFun controller:bit - micro:bit Carrier Board (Qwiic)
OOD!
Price: $19.41
View
Availability: Back Order
Sparkfun Item #: DEV-16129 -

The SparkFun controller:bit is a fun-filled "carrier" board for the micro:bit that, when combined with the micro:bit, provides you with a fully functional controller system. Designed in a similar form factor to the classic Nintendo controller, the controller:bit is equipped with a four-direction "D-pad" on the left side of the board and two action buttons on the right side of the board. The two push buttons on the micro:bit in the center function as start and select to complete the NES...

SparkFun Cryptographic Co-Processor Breakout - ATECC508A (Qwiic)
Price: $9.97
View
Availability: Out of Stock
Sparkfun Item #: DEV-15573 -

The SparkFun ATECC508A Cryptographic Co-processor Breakout allows you to easily add strong authentication security to your IoT node, edge device, or embedded system. It includes two Qwiic ports for plug and play functionality. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard. The ATECC508A chip is capable of many cryptographic processes, including, but...

SparkFun Cryptographic Co-Processor Breakout - ATECC608A (Qwiic)
OOD!
Price: $9.97
View
Availability: Back Order
Sparkfun Item #: SPX-15838 -

The SparkX ATECC608A Cryptographic Co-processor Breakout allows you to add strong security to your IoT node, edge device, or embedded system. This includes asymmetric authentication, symmetric AES-128 encryption/decryption, and much more. Note, the ATECC608A has limited Arduino support and the complete datasheet is under NDA with Microchip. This breakout board includes two Qwiic ports for plug and play functionality. Utilizing our handy Qwiic system, no soldering is required to connect it to...

SparkFun DC/DC Converter Breakout
Price: $53.09
View
Availability: Out of Stock
Sparkfun Item #: BOB-09370 -

This is a breakout board for our non-isolated, 6A DC-to-DC Converter Module. The module can convert any DC voltage between 4.5-14VDC to a selectable voltage between 0.59 and 5.5VDC. To set the output voltage to the desired level, a resistor must be added between the Trim and GND pins. For example, to set the module to output 5V use a 1.34kΩ resistor, or to get 3.3V use a 2.182kΩ. See table 1 in the module's datasheet for more resistor values. The ON/OFF pin on the board can be pulled high to...

SparkFun DeadOn RTC Breakout - DS3234
Price: $37.82
View
Availability: Stocked
Sparkfun Item #: BOB-10160 -

Here is a real time clock based on the DS3234 Real Time Clock IC. The DS3234 is a low-cost, extremely accurate SPI bus real-time clock with an integrated temperature-compensated crystal oscillator and crystal. The RTC maintains seconds, minutes, hours, day, date, month, and year information. The date at the end of the month is automatically adjusted for months with fewer than 31 days, including corrections of leap year. The clock operates in either the 24-hour or 12-hour format with AM/PM...

SparkFun Differential I2C Breakout - PCA9615 (Qwiic)
Price: $19.41
View
Availability: Out of Stock
Sparkfun Item #: BOB-14589 -

The SparkFun Differential I2C Breakout is the fastest and easiest way to extend the range of your I2C communication bus. The breakout uses NXP’s PCA9615 IC, which converts the two default I2C signals into four differential signals, two for SCL and two for SDA. The differential signals are sent over an Ethernet cable, which attaches to the breakout through the on-board RJ-45 connectors The differential signaling allows the I2C signals to reach distances of up to 100ft. while still maintaining...

SparkFun Energy Harvester Breakout - LTC3588
OOD!
Price: $53.09
View
Availability: Back Order
Sparkfun Item #: BOB-09946 -

This breakout board uses the LTC3588 Piezoelectric Energy Harvester from Linear Technologies. This board can be used not only for harvesting piezoelectric energy, but solar energy as well. There is a bridge rectified input for piezo elements (PZ1 and PZ2) and a direct input (VIN) for DC sources. Both are clamped to 20V. In addition, the board can simply be used as a standalone nanopower buck regulator. An ultralow quiescent current undervoltage lockout (UVLO) mode with a wide hysteresis window...

SparkFun FM Tuner Basic Breakout - Si4703
OOD!
Price: $19.41
View
Availability: Back Order
Sparkfun Item #: BOB-11083 -

This breakout for the Silicon Laboratories Si4703 FM tuner chip is a little more stripped down than our FM Tuner Evaluation Board. If your project already has an amp and just needs a full-featured FM tuner, this is the board for you. Beyond being a simple FM radio, the Si4703 is also capable of detecting and processing both Radio Data Service (RDS) and Radio Broadcast Data Service (RBDS) information. The Si4703 even does a very good job of filtering and carrier detection. It also enables data...

SparkFun FM Tuner Evaluation Board - Si4703
OOD!
Price: $38.91
View
Availability: Back Order
Sparkfun Item #: WRL-12938 -

This is an evaluation board for the Silicon Laboratories Si4703 FM tuner chip. Beyond enabling you to tune in to FM radio stations, the Si4703 is also capable of detecting and processing both Radio Data Service (RDS) and Radio Broadcast Data Service (RBDS) information. The Si4703 even does a very good job of filtering and carrier detection. It also enables data such as the station ID and song name to be displayed to the user. Using this board, you will be able to pick up multiple stations just...

SparkFun Full-Bridge Motor Driver Breakout - L298N
OOD!
Price: $5.32
View
Availability: Back Order
Sparkfun Item #: BOB-09540 -

This is a breakout board for the L298N full-bridge dual motor driver; which comes in a staggered, Multiwatt package. All pins of the L298N are broken out to a 15-pin 0.1" pitch header. Two mounting holes are also provided. Features: Board: 1.6x0.85 inches Documents: Schematic Eagle Files Datasheet (L298N) GitHub (Design Files) ...

SparkFun Fuse Breakout Board
OOD!
Price: $3.46
View
Availability: Back Order
Sparkfun Item #: BOB-15697 -

This is a breakout board for the glass ferrule type fuse that fits great with our 5mm fuse clips. Fuses are pretty simple, if current exceeds the rating of the fuse, the small filament inside the fuse heats up and breaks (like a light bulb burning out). The circuit is then broken and hopefully your circuit is saved from molten destruction. For smaller loads, you may want to checkout a PTC (aka resettable fuse). Depending on the PTC's spec, they can handle less current (500mA) but can be set...

SparkFun gator:bit
OOD!
Price: $39.17
View
Availability: Back Order
Sparkfun Item #: DEV-14484 -

The SparkFun gator:bit is an all-in-one “carrier” board for your micro:bit that provides you with a fully functional development and prototyping platform. Almost every pin on the micro:bit is broken out to pads that alligator (or crocodile, if you prefer) clips so you can get the most out of it! Whether it is data visualization using the five on-board addressable LEDs, capacitive touch sensing on pins 0, 1, & 2, or creating musical works of art using the built-in speaker we’ve got it covered...

SparkFun gator:bit v2.0 - micro:bit Carrier Board
OOD!
Price: $36.87
View
Availability: Back Order
Sparkfun Item #: DEV-15162 -

The SparkFun gator:bit v2.0 is an all-in-one “carrier” board for your micro:bit that provides you with a fully functional development and prototyping platform. Almost every pin on the micro:bit is broken out to pads that alligator (or crocodile, if you prefer) clips connect to so you can get the most out of it! Whether it is data visualization using the five on-board addressable LEDs or creating musical works of art using the built-in speaker, we’ve got it covered with the with the SparkFun...

SparkFun gator:RTC - micro:bit Accessory Board
OOD!
Price: $26.50
View
Availability: Back Order
Sparkfun Item #: COM-15486 -

The gator:RTC is a supplemental data logging tool to be used in conjunction with the gator:log, part of SparkFun's gator:bit series of gator-clippable accessories designed for easy interface with the micro:bit or other microcontrollers. This tool allows a student to focus more on the experiment than watching a thermometer or stopwatch. At its core is a RV-3028 real time clock (RTC) module from Micro Crystal, using a convenient I²C bus interface. The module enables you to track the year, month,...

SparkFun Haptic Motor Driver - DRV2605L
Price: $14.09
View
Availability: Out of Stock
Sparkfun Item #: ROB-14538 -

Ready to add some good vibes to your project? Look no further than the SparkFun Haptic Motor Driver. This board breaks out Texas Instruments' DRV2605L Haptic Motor Driver, which adds meaningful feedback from your devices using the breakout and an Arduino-compatible device. The DRV2605L is capable of driving two different types of motors, ERM and LRA. It is important to know, however, that the default firmware for the DRV2605L is set for use with ERM-type motors. We have created an Arduino...

SparkFun I2C DAC Breakout - MCP4725
OOD!
Price: $8.77
View
Availability: Back Order
Sparkfun Item #: BOB-12918 -

You've always wanted to output analog voltages from a microcontroller, the MCP4725 is the DAC that will let you do it! The MCP4725 is an I2C controlled Digital-to-Analog converter (DAC). A DAC allows you to send analog signal, such as a sine wave, from a digital source, such as the I2C interface on the Arduino microcontroller. Digital to analog converters are great for sound generation, musical instruments, and many other creative projects! This version of the MCP4725 Breakout fixes a few...

SparkFun I2S Audio Breakout - MAX98357A
OOD!
Price: $9.75
View
Availability: Back Order
Sparkfun Item #: DEV-14809 -

The SparkFun I2S Audio Breakout board uses the MAX98357A digital to analog converter (DAC), which converts I2S (not be confused with I2C) audio to an analog signal to drive speakers. The I2S Audio Breakout converts the digital audio signals using the I2S standard to an analog signal and amplifies the signal using a class D amplifier which can deliver up to 3.2W of power into a 4Ω load. The board can be configured to output only the left channel audio, right channel, or both. The SparkFun I2S...

SparkFun Large Digit Driver
OOD!
Price: $14.09
View
Availability: Back Order
Sparkfun Item #: WIG-13279 -

The SparkFun Large Digit Driver is a chainable controller backpack that can be soldered directly to the back of our large 6.5" 7-segment displays. Large numerical displays are a great addition to any project where you want to be able to see information at a distance. Scorekeepers and lap timers would be a great application for large 7-segment LED displays. The SparkFun Large Digit Driver can easily be attached to the back of the 7-segment display by soldering all 10 castellations pins at the...

SparkFun LED Driver Breakout - LP55231
OOD!
Price: $15.86
View
Availability: Back Order
Sparkfun Item #: BOB-13884 -

The SparkFun LP55231 LED Driver Breakout is a self-contained solution for developing and deploying the nine-channel I2C LED controller. Remarkably simple, the breakout is equipped primarily with just the LP55231 LED controller IC, plus three RGB LEDs. It also features pads and jumpers for replacing the onboard LEDs with external ones, and configuring the I2C bus, which allows you to daisy-chain up to four LP55231s. This breakout drives the LEDs using Pulse Width Modulation (PWM), so it is...

SparkFun LED Driver Breakout - TLC5940 (16 Channel)
Price: $26.99
View
Availability: Back Order
Sparkfun Item #: BOB-10616 -

The TLC5940 is a 16 channel PWM unit with 12 bit duty cycle control (0-4095), 6 bit current limit control (0-63), and a daisy chainable serial interface. This breakout board is a good way to take full advantage of this useful IC. All 16 PWM channels are broken out to standard 0.1" headers, which run alongside convenient voltage and ground rails. Also, because the TLC5940 can be daisy-chained, the breakout is designed to support that feature. On the left-hand side of the board all serial inputs...