Electronics (Kits, Makers, Robotics, Components)

This is a resistive analog joystick, very similar to those found on the PSP1000. These compact joysticks are different in that they have a very interesting 'slide' feeling. For wiring this part, if...

This is a resistive analog joystick, very similar to those found on the PSP1000. These compact joysticks are different in that they have a very interesting 'slide' feeling. For wiring this part, if you look at the device from the bottom the pin out goes 1) x-axis output 2) +5V 3) y-axis output 4) gnd Pin 4 is the pin closest to the 2 mounting tabs found on one side of the device. When connected to an Arduino, you can expect a range of about 128 to 775 on each axis. The rubber thumb pad is...

This is a ultra compact size Dual-H-Bridge dc motor driver (Based on HR8833), which could drive two way 1.5A DC brush motors up to 10V . It has the same footprint as your thumbnail suitable for...

This is a ultra compact size Dual-H-Bridge dc motor driver (Based on HR8833), which could drive two way 1.5A DC brush motors up to 10V . It has the same footprint as your thumbnail suitable for projects with limited spaces. Both sides of the module are desgined with standard XH2.54 pins, which allows you to plug it on a breadboard or prototype board. Caption|Specification| Logic Input Voltage (VCC): 3.3-5V Load Supply Voltage (VM): 3.3-10V Maximum Continuous Operating Current: 1500mA( Single)...

This AT407 basic tilt switch can easily be used to detect orientation. Inside the can is a ball that make contact with the pins when the case is upright. Tilt the case over and the balls don't...

This AT407 basic tilt switch can easily be used to detect orientation. Inside the can is a ball that make contact with the pins when the case is upright. Tilt the case over and the balls don't touch, thus not making a connection. There are numerous uses for these basic sensors, but keep in mind you might need to use some debouncing code, as the sensor isn't immune to small vibrations and such. Documents: Datasheet GitHub (Firmware) Videos ...

Tilt-a-Whirl Breakout - RPI-1031 Description: The RPI-1031 tilt sensor is capable of sensing a change in orientation in four different directions: forward, back, left or right. This breakout...

Tilt-a-Whirl Breakout - RPI-1031 Description: The RPI-1031 tilt sensor is capable of sensing a change in orientation in four different directions: forward, back, left or right. This breakout board makes it easier to incorporate the RPI-1031 in your next project by breaking the necessary pins out to standard 0.1" spaced headers. This board will work at either 3.3 or 5V. Documents: Schematic Eagle Files Datasheet (RPI-1031) Product Page(RPI-1031) Hookup Guide bildr Tutorial Product...

The EVK75123 is the evaluation kit for the MLX75023 and MLX75123 Time-of-Flight (TOF) chipset. This new chipset enables real-time 3D imaging at full QVGA resolution with unsurpassed sunlight...

The EVK75123 is the evaluation kit for the MLX75023 and MLX75123 Time-of-Flight (TOF) chipset. This new chipset enables real-time 3D imaging at full QVGA resolution with unsurpassed sunlight robustness. The evaluation kit is a complete camera built around this chipset and can be directly connected to a PC for visualization and recording of depth map data, while allowing direct access to many configuration settings. EVK75123 is a modular plug and play platform perfectly set up for customization...

The TIMI to MikroBUS™ adapter is designed to provide development boards/modules which have a mikroBUS™ Click socket, with a MatesBUS interface, to connect products such as the TIMI-96 directly. This...

The TIMI to MikroBUS™ adapter is designed to provide development boards/modules which have a mikroBUS™ Click socket, with a MatesBUS interface, to connect products such as the TIMI-96 directly. This adapter provides any board that supports the mikroBUS™ Click socket with a MatesBUS interface to connect products of any TIMI model directly to the Raspberry Pi bus. The MikroBUS™ Adapter features a 5-pin programming header to program the connected device directly through the Click Adapter, using...

TIMI-96 is a unique breadboard compatible display development module, aimed to speed up and reinvent the way electronic testing, development and projects are carried out, in either stand alone, host...

TIMI-96 is a unique breadboard compatible display development module, aimed to speed up and reinvent the way electronic testing, development and projects are carried out, in either stand alone, host interfaced, PC tethered, or educational settings. Wrapped in a sleek metal frame, TIMI can be viewed at any angle. Boasting a full RBG (65K vivid colors) display with 160×80 resolution. TIMI is a 0.96” TFT LCD display module that is driven directly by a PIXXI-28 graphics processor from 4D Labs. It...

TIMI-96 is a unique breadboard compatible display development module, aimed to speed up and reinvent the way electronic testing, development and projects are carried out, in either stand alone, host...

TIMI-96 is a unique breadboard compatible display development module, aimed to speed up and reinvent the way electronic testing, development and projects are carried out, in either stand alone, host interfaced, PC tethered, or educational settings. Wrapped in a sleek metal frame, TIMI can be viewed at any angle. Boasting a full RBG (65K vivid colors) display with 160×80 resolution. TIMI is a 0.96” TFT LCD display module that is driven directly by a PIXXI-28 graphics processor from 4D Labs. It...

TIMI-MB (mikroBUS™) is a unique breadboard compatible display development module designed to provide development boards/modules which have a mikroBUS™ Click socket a simple to interface display...

TIMI-MB (mikroBUS™) is a unique breadboard compatible display development module designed to provide development boards/modules which have a mikroBUS™ Click socket a simple to interface display solution. TIMI-MB is aimed to speed up and reinvent the way electronic testing, development and projects are carried out. Wrapped in a sleek metal frame, TIMI can be viewed at any angle. Boasting a full RBG (65K vivid colors) display with 160×80 resolution. TIMI-MB is a 0.96” TFT LCD display module that...

TIMI-MB (mikroBUS™) is a unique breadboard compatible display development module designed to provide development boards/modules which have a mikroBUS™ Click socket a simple to interface display...

TIMI-MB (mikroBUS™) is a unique breadboard compatible display development module designed to provide development boards/modules which have a mikroBUS™ Click socket a simple to interface display solution. TIMI-MB is aimed to speed up and reinvent the way electronic testing, development and projects are carried out. This Starter Kit version features a TIMI-MB and a Mates Programmer to get you started as easily as possible! Wrapped in a sleek metal frame, TIMI can be viewed at any angle. Boasting...

    This is a new version of infrared distance switch. It has small size and higher ranging, it is able to detect ranging from 3cm to 100cm. It is tiny, easy to use/assemble, and...

    This is a new version of infrared distance switch. It has small size and higher ranging, it is able to detect ranging from 3cm to 100cm. It is tiny, easy to use/assemble, and inexpensive. Useful for robotics, interactive media, industrial assembly line, etc. Specification Power supply: 3.8v-5.5v Current(5v): 6mA Range: 3-100cm adjustable Wiki & External links Wiki link ...

The ATtiny45 and 85 are a couple of really cool little MCUs but did you know you can program them in Arduino? That's right, now you can shrink your Arduino projects down to "tiny size" by moving...

The ATtiny45 and 85 are a couple of really cool little MCUs but did you know you can program them in Arduino? That's right, now you can shrink your Arduino projects down to "tiny size" by moving your code straight over to these small but capable ICs. The standard method for programming the ATtiny ICs involves a breadboard, lots of jumper wires and a hardware programmer, but David Mellis over at MIT Media Lab has simplified the process by laying out this handy USB programmer. The Tiny AVR...

This is a stepper motor driver introduced by DFRobot for those projects require powerful stepper motors, such as a pair of automatic curtains, an XY Plotter. This shield allows Arduino drive stepper...

This is a stepper motor driver introduced by DFRobot for those projects require powerful stepper motors, such as a pair of automatic curtains, an XY Plotter. This shield allows Arduino drive stepper motors (up to 2A per motor coil, 40V max). This stepper motor drive shied adoptes a TMC260 chip which is the first energy efficient high precision microstepping driver IC for bipolar stepper motors with integrated power MOSFETs. The unique high resolution sensorless load detection...

This is a heavy duty SPST toggle switch - your basic on/off toggle. Rated for 2A at 250V or 4A at 125V. Includes a face plate and two threaded nuts for mounting. Works great with our missile switch...

This is a heavy duty SPST toggle switch - your basic on/off toggle. Rated for 2A at 250V or 4A at 125V. Includes a face plate and two threaded nuts for mounting. Works great with our missile switch cover. Features: 0.5 x 0.55 x 1.45" Documents: Dimensional Drawing

This simple on-off switch is rated for 20A at 12V but who cares about all that, it looks way awesome. These toggle switches come with those missile switch covers that make your project look like...

This simple on-off switch is rated for 20A at 12V but who cares about all that, it looks way awesome. These toggle switches come with those missile switch covers that make your project look like something out of a spy movie. They're also a great safety feature to ensure that you don't accidentally fire the missiles (or whatever it is your switch does). As if you needed any more convincing, they're also illuminated with a small LED in the end of the switch. These can be panel mounted into a...

There's nothing worse than getting ready for a good hack and then realizing that you can't even get the box open because you don't have the right screwdriver. Sure, we all have a few Phillips-head...

There's nothing worse than getting ready for a good hack and then realizing that you can't even get the box open because you don't have the right screwdriver. Sure, we all have a few Phillips-head drivers and maybe a few slotted drivers but what about Torx, Hex Socket or Tri-Wing? This kit has them all. Along with a large variety of interchangeable bits and a hard ABS plastic handle, the kit also includes a steel extension bar and a flexible extension neck that really comes in handy when...

    Tower Pro SG90 is a high quality, low-cost servo for all your mechatronic needs. It comes with a 3-pin power and control cable, mounting hardware. Specification Operating...

    Tower Pro SG90 is a high quality, low-cost servo for all your mechatronic needs. It comes with a 3-pin power and control cable, mounting hardware. Specification Operating Voltage: 4.8 ~ 6.0V Operating Speed: 0.12sec/60 degree(4.8V)~0.1sec/60 degree(6.0V) Torque: 1.6kg/cm(4.8V) Dead Band Width: 5usec Temperature Range: -30?~+60? Cable Length: 25cm Brand name: Tower Pro location of each pin: red (+), brown (-), yellow (signal). ...

The TowerPro SG90C is a 360 degree micro servo. It uses a plastic gear drive and is light and compact. It can be used for various applications and DIY products, such as toy cars, boats, windmills...

The TowerPro SG90C is a 360 degree micro servo. It uses a plastic gear drive and is light and compact. It can be used for various applications and DIY products, such as toy cars, boats, windmills etc. A 360 degree servo’s operation is more similar to a DC motor than a standard servo as only rotation direction and speed can be controlled. There is also no hardware stop inside so that the shaft can rotate freely. Compared to an ordinary DC motor, a 360-degree servo motor does not require...

Transceiver nRF2401A Module Trace AntennaDescription: Miniature RF (MiRF) 2.4GHz transceiver modules with built in antenna designed around the Nordic Semiconductor nRF2401A with high sensitivity and...

Transceiver nRF2401A Module Trace AntennaDescription: Miniature RF (MiRF) 2.4GHz transceiver modules with built in antenna designed around the Nordic Semiconductor nRF2401A with high sensitivity and good range. These units are a SparkFun exclusive; small in stature, big on performance, all wrapped up in a user friendly package. Units come with an empty 0.1" spaced footprint ready for a straight header, right angle header (recommended), or your own wires/umbilical cable.The...

The Balun Ember Transformers from Wurth Elektronik allow you to convert an unbalanced signal in a transmission line to a balanced one, or vice versa. Each of these ICs possesses a frequency range of...

The Balun Ember Transformers from Wurth Elektronik allow you to convert an unbalanced signal in a transmission line to a balanced one, or vice versa. Each of these ICs possesses a frequency range of 2400MHz to 2500MHz with an impedance of 50 ohms unbalanced and 100 ohms balanced. These come as cut tape. Documents: Datasheet

This is the 2N5192G, an NPN silicon transistor. This little transistor can help in your project by being used to help drive large loads or amplifying or switching applications. The 2N5192G is...

This is the 2N5192G, an NPN silicon transistor. This little transistor can help in your project by being used to help drive large loads or amplifying or switching applications. The 2N5192G is specifically rated at 60V and 4A max. Documents: Datasheet

This is the BC337, an NPN silicon BJT (Bipolar Junction Transistor). This little transistor can help in your project by being used to help drive large loads or amplifying or switching applications....

This is the BC337, an NPN silicon BJT (Bipolar Junction Transistor). This little transistor can help in your project by being used to help drive large loads or amplifying or switching applications. The BC337 is specifically rated at 50V and 800mA max. Note: The BC337 is a drop-in replacement for the P2N2222A Transistor Documents: Datasheet

These are very common, high quality BJT NPN transistors made by ST Micro. Datasheet: 2N3904

These are very common, high quality BJT NPN transistors made by ST Micro. Datasheet: 2N3904

These are very common, high quality BJT, PNP transistors made by ST Micro. **Datasheet: **2N3906

These are very common, high quality BJT, PNP transistors made by ST Micro. **Datasheet: **2N3906

The Raspberry Pi is a low cost, credit-card sized computer that plugs into a computer monitor or TV, and uses a standard keyboard and mouse. It is a capable little device that enables people of all...

The Raspberry Pi is a low cost, credit-card sized computer that plugs into a computer monitor or TV, and uses a standard keyboard and mouse. It is a capable little device that enables people of all ages to explore computing, and to learn how to program in languages like Scratch and Python. It’s capable of doing everything you’d expect a desktop computer to do, from browsing the internet and playing high-definition video, to making spreadsheets, word-processing, and playing...

It is a cost-effective shell for your Micro: bit development board. The shell has a transparent acrylic body, which can allow you see the inside clearly. It can be assembled yourselves, and there is...

It is a cost-effective shell for your Micro: bit development board. The shell has a transparent acrylic body, which can allow you see the inside clearly. It can be assembled yourselves, and there is no lock, so it is easy to assemble. It is designed for Micro: bit development board, the high practical value and beautiful looking can be a great choice for you. Specifications Color: transparent Size: 33x86mm Material: acrylic Package list Transparent Acrylic Shell for Micro: bit x 1 ...

The Raspberry Pi is a low cost, credit-card sized computer that plugs into a computer monitor or TV, and uses a standard keyboard and mouse. It is a capable little device that enables people of all...

The Raspberry Pi is a low cost, credit-card sized computer that plugs into a computer monitor or TV, and uses a standard keyboard and mouse. It is a capable little device that enables people of all ages to explore computing, and to learn how to program in languages like Scratch and Python. It’s capable of doing everything you’d expect a desktop computer to do, from browsing the internet and playing high-definition video, to making spreadsheets, word-processing, and playing...

There are lots of trimpots out there. Some are very large, some so small they require a screwdriver. Here at SparkFun, we just needed a simple one that worked. This 10K trimmable potentiometer has a...

There are lots of trimpots out there. Some are very large, some so small they require a screwdriver. Here at SparkFun, we just needed a simple one that worked. This 10K trimmable potentiometer has a small knob built right in and it's breadboard friendly to boot! Perfect for your next LCD contrast adjuster, opamp setting, or volume level. This model # is TSR-3386U within the datasheet. Documents: Datasheet (Note pins are in a single row, as shown in the pictures) ...

Breakout board for the Analog Device ADXL345. The ADXL345 is a small, thin, low power, 3-axis accelerometer with high resolution (13-bit) measurement at up to &;plusmn;16 g. Digital output data is...

Breakout board for the Analog Device ADXL345. The ADXL345 is a small, thin, low power, 3-axis accelerometer with high resolution (13-bit) measurement at up to &;plusmn;16 g. Digital output data is formatted as 16-bit twos complement and is accessible through either a SPI (3- or 4-wire) or I2C digital interface. The ADXL345 is well suited to measures the static acceleration of gravity in tilt-sensing applications, as well as dynamic acceleration resulting from motion or shock. Its high...

This Triple Axis Accelerometer with Bosch BMA220 is an ultra small triaxial, low-g acceleration sensor breakboard with SPI and I2C interface, aiming for low power consumer market applications. It...

This Triple Axis Accelerometer with Bosch BMA220 is an ultra small triaxial, low-g acceleration sensor breakboard with SPI and I2C interface, aiming for low power consumer market applications. It allows measurement of accelerations in 3 perpendicular axes and thus senses tilt, motion, shock and vibration in cell phones, handhelds, computer peripherals, man-machine interfaces, virtual reality features and game controllers. With a size of only 2 mm x 2 mm, the Bosch BMA220 represents a new...

    This is a breakout board for Freescale's MMA7361L three-axis analog accelerometer. The sensor requires a very low amount of power and has a g-select input which switches the...

    This is a breakout board for Freescale's MMA7361L three-axis analog accelerometer. The sensor requires a very low amount of power and has a g-select input which switches the accelerometer between ?1.5g and ?6g measurement ranges. Other features include a sleep mode, signal conditioning, a 1-pole low pass filter, temperature compensation, self test, and 0g-detect which detects linear freefall. Zero-g offset and sensitivity are factory set and require no external devices....

3-Axis acceleration sensor is an electronic equipment which could measure the acceleration during the object motion. It could help you to analyse the target motion position or direction. The typical...

3-Axis acceleration sensor is an electronic equipment which could measure the acceleration during the object motion. It could help you to analyse the target motion position or direction. The typical interactive application could be the posture recognition and action recognition, such as WII game applications. These video game device are all using internal acceleration sensor, calculate the current motion direction by conversion algorithm. And most of the recent smart device are based the same...

Triple Axis Accelerometer MMA7260 The MMA7260Q is a very nice sensor with easy analog interface. The MMA7260QT is a 3.3V part and outputs an analog voltage for each of the three outputs. This...

Triple Axis Accelerometer MMA7260 The MMA7260Q is a very nice sensor with easy analog interface. The MMA7260QT is a 3.3V part and outputs an analog voltage for each of the three outputs. This voltage is in ratio to the measured acceleration and to the supply voltage (ratiometric). It has selectable sensitivity by dip switch.  You will need some extra hardware to convert this analog signal to a usable digital one.  The Arduino is really good option for it.  This break...

The MMA7361 from Freescale is a very nice IMU sensor with easy analog interface. The MMA7361 Arduino is a 3.3V part and outputs an analog voltage for each of the three outputs. This voltage is in...

The MMA7361 from Freescale is a very nice IMU sensor with easy analog interface. The MMA7361 Arduino is a 3.3V part and outputs an analog voltage for each of the three outputs. This voltage is in ratio to the measured acceleration and to the supply voltage (ratiometric). It has selectable sensitivity by dip switch. You will need some extra hardware to convert this analog signal to a usable digital one. The Arduino is really good option for it. This break board is especially designed for...

So much power and light from such a small package. This 3W per channel, Triple Output High Power RGB LED is sure to shed a lot of light on any project you add it to. This LED acts as any other LED...

So much power and light from such a small package. This 3W per channel, Triple Output High Power RGB LED is sure to shed a lot of light on any project you add it to. This LED acts as any other LED except they require much more power while delivering a light as intense of a thousand suns going super nova (this is an exaggeration but you know what we mean)! Please be aware that with all three LEDs (9W total output), you will need additional heat sinking. This LED sits upon an aluminum backed PCB...

This is the very popular RGB combo but in SMD form. These units have four pads with a common anode configuration. Use this one LED for three status indicators or pulse width modulate all three and...

This is the very popular RGB combo but in SMD form. These units have four pads with a common anode configuration. Use this one LED for three status indicators or pulse width modulate all three and get mixed colors! Simple breakout board available below. Iv (Typical): Red: 81mcd Green: 130mcd Blue: 54mcd Vf (Typical): Red: 2.0V Green: 3.5V Blue: 3.5V Wavelength (λD - nm): Red: 615nm Green: 530nm Blue: 470nm Documents: Datasheet LED Tutorial ...

TRRS connectors are the audio-style connectors that you see on some phones, MP3 players and development boards. TRRS stands for "Tip, Ring, Ring, Sleeve," which reflects the fact that, unlike a...

TRRS connectors are the audio-style connectors that you see on some phones, MP3 players and development boards. TRRS stands for "Tip, Ring, Ring, Sleeve," which reflects the fact that, unlike a standard stereo connector, this actually has three conductors and a ground. Some devices use the extra conductor for a microphone (like hands-free headsets) or to carry a video signal (like in some MP3/MP4 players). If you're hacking on something that has a 4-conductor audio jack, being able to plug...

Based on a new generation ARM Cortex M7, the Qwiic Tsunami Super WAV Trigger extends polyphony to 32 mono or 18 stereo simultaneous uncompressed 44.1kHz, 16-bit tracks. Each track can start, pause,...

Based on a new generation ARM Cortex M7, the Qwiic Tsunami Super WAV Trigger extends polyphony to 32 mono or 18 stereo simultaneous uncompressed 44.1kHz, 16-bit tracks. Each track can start, pause, resume, loop and stop independently, and can have its own volume setting, allowing you to create the perfect interactive mix of music, dialog and sound effects. The Qwiic Tsunami also supports true seamless looping over an arbitrary track length. Utilizing our handy Qwiic system, no soldering is...

Based on a new generation ARM Cortex M7, this version of the Qwiic Tsunami Super WAV Trigger extends polyphony to 25 mono or 13 stereo simultaneous uncompressed 44.1kHz, 16-bit tracks. Each track...

Based on a new generation ARM Cortex M7, this version of the Qwiic Tsunami Super WAV Trigger extends polyphony to 25 mono or 13 stereo simultaneous uncompressed 44.1kHz, 16-bit tracks. Each track can start, pause, resume, loop, and stop independently, and can have its own volume setting, allowing you to create the perfect interactive mix of music, dialog, and sound effects. The Qwiic Tsunami also supports true seamless looping over an arbitrary track length. Utilizing our handy Qwiic system,...

This is a TT Micro DC Geared Motor with Back Shaft working at 6V with 160rpm. The TT motor series the most popular DC motors for DIY enthusiasts. It is designed to easily incorporate the DFRobot...

This is a TT Micro DC Geared Motor with Back Shaft working at 6V with 160rpm. The TT motor series the most popular DC motors for DIY enthusiasts. It is designed to easily incorporate the DFRobot Encoder. These motors are inexpensive, small, easy to install, and ideally suited for use in a mobile robot. The DFRobot ROMEO microcontroller is able to complete the closed-loop PID making use of the Gravity:TT Motor Encoders Kit. We recommend this rubber wheel for this motor. |Specification|Electrical...

These 2" long aluminum tubes have an outer diameter of 1", an inner diameter of 0.82", and a wall thickness of 0.09". When used with the mating tube clamps, these can be used for versatile...

These 2" long aluminum tubes have an outer diameter of 1", an inner diameter of 0.82", and a wall thickness of 0.09". When used with the mating tube clamps, these can be used for versatile structural support. Additionally, wires and cables can easily be run through the center. Features: Length - 2.0" OD - 1" ID - 0.82" Width - 0.09"

These 4" long aluminum tubes have an outer diameter of 1", an inner diameter of 0.82", and a wall thickness of 0.09". When used with the mating tube clamps, these can be used for versatile...

These 4" long aluminum tubes have an outer diameter of 1", an inner diameter of 0.82", and a wall thickness of 0.09". When used with the mating tube clamps, these can be used for versatile structural support. Additionally, wires and cables can easily be run through the center. Features: Length - 4.0" OD - 1" ID - 0.82" Width - 0.09"

These 10" long aluminum tubes have an outer diameter of 3/8", an inner diameter of 0.30", and a wall thickness of 0.035". When used with the mating tube clamps, these can be used for versatile...

These 10" long aluminum tubes have an outer diameter of 3/8", an inner diameter of 0.30", and a wall thickness of 0.035". When used with the mating tube clamps, these can be used for versatile structural support. Additionally, wires and cables can easily be run through the center. Features: Length - 10.0" OD - 3/8" ID - 0.30" Width - 0.035"

These 10" long stainless steel tubes have an outer diameter of 1", an inner diameter of 0.88", and a wall thickness of 0.06". When used with the mating tube clamps, these can be used for versatile...

These 10" long stainless steel tubes have an outer diameter of 1", an inner diameter of 0.88", and a wall thickness of 0.06". When used with the mating tube clamps, these can be used for versatile structural support. Additionally, wires and cables can easily be run through the center. Features: Length - 10.0" OD - 1" ID - 0.88" Width - 0.06"

These 8" long stainless steel tubes have an outer diameter of 1", an inner diameter of 0.88", and a wall thickness of 0.06". When used with the mating tube clamps, these can be used for versatile...

These 8" long stainless steel tubes have an outer diameter of 1", an inner diameter of 0.88", and a wall thickness of 0.06". When used with the mating tube clamps, these can be used for versatile structural support. Additionally, wires and cables can easily be run through the center. Features: Length - 8" OD - 1" ID - 0.88" Width - 0.06"

These 10" long aluminum tubes have an outer diameter of 5/8", an inner diameter of 0.569", and a wall thickness of 0.028". When used with the mating tube clamps, these can be used for versatile...

These 10" long aluminum tubes have an outer diameter of 5/8", an inner diameter of 0.569", and a wall thickness of 0.028". When used with the mating tube clamps, these can be used for versatile structural support. Additionally, wires and cables can easily be run through the center. Features: Length - 10.0" OD - 5/8" ID - 0.569" Width - 0.028"

The Turtle 2WD DIY Robotics building kit is a entry level programmable robot kit based on Arduino.With just a few simple steps of assembling the hardware and tuning the software, and you'll learn...

The Turtle 2WD DIY Robotics building kit is a entry level programmable robot kit based on Arduino.With just a few simple steps of assembling the hardware and tuning the software, and you'll learn all about Arduino, robotics, sensors, bluetooth communication — as well as obstacle avoidance and remote controlling. You can also take it further with your own code to take advantage of the ultrasonic sensor, Romeo ( a Bluetooth 4.0 (BLE) Arduino Microcontroller ) , IR distance sensors and...

The 2WD Mobile Robot Platform for Arduino is a small, low-cost mobile platform for use with a standard Arduino microcontroller. The robot comes as a kit which includes two drive motors, wheels (and...

The 2WD Mobile Robot Platform for Arduino is a small, low-cost mobile platform for use with a standard Arduino microcontroller. The robot comes as a kit which includes two drive motors, wheels (and rear caster ball), frame and all mounting hardware. The main structure and mechanical parts for a robot.This DFRobot mobile robot platform is widely used as self-developed control chasis for Arduino platforms and other control boards. This kit features the following: two differential drives, near...

These are nice, cross-locking, curved tweezers, unlike traditional models the tips on these tweezers will remain closed until squeezed open. They have a nice, rounded tip which allows you to pick up...

These are nice, cross-locking, curved tweezers, unlike traditional models the tips on these tweezers will remain closed until squeezed open. They have a nice, rounded tip which allows you to pick up very small parts with precision. This is a great tool to have if you're working with surface mount components or anything with very small parts. The ESD-safe coating will also help prevent electro-static damage to sensitive electronic components. Documents: Product Video ...

You can tell by our large assortment of tweezers that we here at SparkFun are way into picking up tiny things. To make sure we're always up to date on the latest in 'tweezing' technology, we're...

You can tell by our large assortment of tweezers that we here at SparkFun are way into picking up tiny things. To make sure we're always up to date on the latest in 'tweezing' technology, we're always buying and testing new tweezers. Okay... tweezers aren't exactly the most exciting thing in the world, but they are super handy. These are nice, solid curved tweezers. They have a very fine tip which allows you to pick up very small parts with precision. This is a great tool to have if you're...

These are nice, cross-locking, straight tweezers, unlike traditional models the tips on these tweezers will remain closed until squeezed open. They have a very fine tip which allows you to pick up...

These are nice, cross-locking, straight tweezers, unlike traditional models the tips on these tweezers will remain closed until squeezed open. They have a very fine tip which allows you to pick up very small parts with precision. This is a great tool to have if you're working with surface mount components or anything with very small parts. The ESD-safe coating will also help prevent electro-static damage to sensitive electronic components. Documents: Product Video ...

You can tell by our large assortment of tweezers that we here at SparkFun are way into picking up tiny things. To make sure we're always up to date on the latest in 'tweezing' technology, we're...

You can tell by our large assortment of tweezers that we here at SparkFun are way into picking up tiny things. To make sure we're always up to date on the latest in 'tweezing' technology, we're always buying and testing new tweezers. Okay... tweezers aren't exactly the most exciting thing in the world, but they are super handy. These are nice, solid straight tweezers. They have a very fine tip which allows you to pick up very small parts with precision. This is a great tool to have if you're...

    This is a Type-B USB cable, which compatible with Arduino Uno. It's a 3m cable and long enough for normal use. ...

    This is a Type-B USB cable, which compatible with Arduino Uno. It's a 3m cable and long enough for normal use.

This is a time saving kit of jumper wires - cut, stripped,bent 90 degree on both ends for easy insertion and your prototyping pleasure. Make your prototyping neat and looks nicer, The box included...

This is a time saving kit of jumper wires - cut, stripped,bent 90 degree on both ends for easy insertion and your prototyping pleasure. Make your prototyping neat and looks nicer, The box included with this kit are 14 various lengths of 22AWG wire - 2, 5, 7, 10, 12, 15, 17, 20, 22, 25, 50, 75, 100, and 125mm - 10 pieces of each. Various colors of jumper wire, perfectly fit for breadboard and protoboard. 140pcs a box, get one and use in your future project again and again! |Specification| #22...

The u-blox ANN-MB5 multi-band (L1/L5/E5a/B2a/NavIC) active GNSS antenna is designed for the new generation of multi-frequency, multi-constellation standard precision GNSS technology, which can...

The u-blox ANN-MB5 multi-band (L1/L5/E5a/B2a/NavIC) active GNSS antenna is designed for the new generation of multi-frequency, multi-constellation standard precision GNSS technology, which can achieve the most accurate, reliable, and robust positioning even in challenging environments. ANN-MB5’s compact design, excellent price-to-performance ratio, and easy mounting features ensure a fast, easy, and reliable multi-band antenna solution for mass adoption. ANN-MB5 is a perfect match to the...

u-blox SARA-R5 series LTE-M/NB-IoT Modules are used to secure the cloud LTE Cat M1 and LTE Cat NB2 solutions based on UBX-R5 cellular chipset. These modules deliver high-performance satellite...

u-blox SARA-R5 series LTE-M/NB-IoT Modules are used to secure the cloud LTE Cat M1 and LTE Cat NB2 solutions based on UBX-R5 cellular chipset. These modules deliver high-performance satellite positioning with data connectivity in the very small and compact SARA form factor. The SARA LGA form factor (26mm x 16mm and 96-pin) allows easy integration into compact designs and seamless drop-in migration from other cellular module families. These LTE-M modules provide software-based multi-band...

More and more of our products use U.FL connectors, so we wrote a tutorial on "Three Quick Tips About Using U.FL. However, even when following all the best practices outlined in the tutorial, we...

More and more of our products use U.FL connectors, so we wrote a tutorial on "Three Quick Tips About Using U.FL. However, even when following all the best practices outlined in the tutorial, we managed to rip more than a few connectors apart and it's always a disaster! Are you having issues disconnecting your U.FL connectors from each other? Well now you can ease the disconnection process with this handy little extraction tool. We have started to use this in our internal testing and we think...

This cute little coax is a champ in our RF kit! It has a right angle female U.FL (aka I-PEX) connector on both ends. Now instead of jerry-rigging a few U.FL to SMA cables together we can go straight...

This cute little coax is a champ in our RF kit! It has a right angle female U.FL (aka I-PEX) connector on both ends. Now instead of jerry-rigging a few U.FL to SMA cables together we can go straight from one U.FL device to another. As an added bonus this coax is the nice stuff - approximately 1mm in diameter and extra flexible. The 50-ohm impedance of this cable makes it well suited for almost all SparkFun RF products including GPS, LoRa, and RFID. Features: 200 mm length 1.25 mm diameter U.FL...

Uh-oh Battery Level Indicator Kit Description: Under-powering a digital device can sometimes have pretty nasty consequences. Brown-out conditions can cause memory to get written or overwritten in...

Uh-oh Battery Level Indicator Kit Description: Under-powering a digital device can sometimes have pretty nasty consequences. Brown-out conditions can cause memory to get written or overwritten in odd ways, can cause unexpected behavior in connected systems and just generally screw up your day. One way to avoid this is to keep an eye on your battery voltage and turn off the system before it gets too low (or plug it in). We've whipped up a little board to help you out with this...

This is your solution when you absolutely, positively need to get the most out of an antenna for your next RFID project. This ultra high-frequency (UHF) RFID Antenna boasts a frequency range of...

This is your solution when you absolutely, positively need to get the most out of an antenna for your next RFID project. This ultra high-frequency (UHF) RFID Antenna boasts a frequency range of 860-960 MHz with a gain of 6dBi. This is the same external antenna we use for our Simultaneous RFID Reader due to its high-quality features. Each UHF RFID Antenna is terminated with a 30cm long TNC Female RP cable. If you need to extend the cable attached to the antenna, we offer additional cords to...

These paper-thin, adhesive EPCglobal Gen2 tags work with our Simultaneous RFID Reader and can be stuck to practically anything you can imagine. The tags can read and be written to --- and also have...

These paper-thin, adhesive EPCglobal Gen2 tags work with our Simultaneous RFID Reader and can be stuck to practically anything you can imagine. The tags can read and be written to --- and also have a kill feature. Each tag comes with a TID (Truly Unique ID) that can't be changed, but there's plenty of memory for you to write and read from. Compatible with all of our RAIN UHF RFID Reader and Writers. Features: 30mm x 16mm Works with our UHF RFID Readers and Writers Adhesive backing Documents:...

These paper-thin, adhesive EPCglobal Gen2 tags work with our Simultaneous RFID Reader and can be stuck to practically anything you can imagine. The tags can read and be written to --- and also have...

These paper-thin, adhesive EPCglobal Gen2 tags work with our Simultaneous RFID Reader and can be stuck to practically anything you can imagine. The tags can read and be written to --- and also have a kill feature. Each tag comes with a TID (Truly Unique ID) that can't be changed, but there's plenty of memory for you to write and read from. Compatible with all of our RAIN UHF RFID Reader and Writers. Features: 30mm x 16mm Works with our UHF RFID Readers and Writers Adhesive backing Documents:...

This is the HC-SR04-33 ultrasonic distance sensor. This economical sensor provides 2cm to 400cm of non-contact measurement functionality with a ranging accuracy that can reach up to 3mm. Each...

This is the HC-SR04-33 ultrasonic distance sensor. This economical sensor provides 2cm to 400cm of non-contact measurement functionality with a ranging accuracy that can reach up to 3mm. Each HC-SR04-33 module includes an ultrasonic transmitter, a receiver and a control circuit. There are only four pins that you need to worry about on the HC-SR04: VCC (Power), Trig (Trigger), Echo (Receive), and GND (Ground). You will find this sensor very easy to set up and use for your next range-finding...

This is the HC-SR04 ultrasonic distance sensor. This economical sensor provides 2cm to 400cm of non-contact measurement functionality with a ranging accuracy that can reach up to 3mm. Each HC-SR04...

This is the HC-SR04 ultrasonic distance sensor. This economical sensor provides 2cm to 400cm of non-contact measurement functionality with a ranging accuracy that can reach up to 3mm. Each HC-SR04 module includes an ultrasonic transmitter, a receiver and a control circuit. There are only four pins that you need to worry about on the HC-SR04: VCC (Power), Trig (Trigger), Echo (Receive), and GND (Ground). You will find this sensor very easy to set up and use for your next range-finding project!...