Electronics (Kits, Makers, Robotics, Components)

Huge 10mm through-hole LEDs. Mood-light an entire wall! Features: 3.0-3.4VDC Forward Voltage 80mA Forward Current 30 degree viewing angle 16,000-20,000 MCD output Documents: Datasheet LED Tutorial ...

Huge 10mm through-hole LEDs. Mood-light an entire wall! Features: 3.0-3.4VDC Forward Voltage 80mA Forward Current 30 degree viewing angle 16,000-20,000 MCD output Documents: Datasheet LED Tutorial

Yes you read that correctly - 10Farad capacitor. This small cap can be charged up and then slowly dissipated running an entire system for hours. Combine two in series for 5F/5V. Do not over voltage...

Yes you read that correctly - 10Farad capacitor. This small cap can be charged up and then slowly dissipated running an entire system for hours. Combine two in series for 5F/5V. Do not over voltage or reverse polarize these capacitors. Features: 13mm x 33.5mm Documents: Datasheet

"Guess what?! Super-Awesome Sylvia, star of Super-Awesome Sylvia’s Super-Awesome Maker Show has a new book for young makers! It’s called, “Sylvia’s Super-Awesome Project...

"Guess what?! Super-Awesome Sylvia, star of Super-Awesome Sylvia’s Super-Awesome Maker Show has a new book for young makers! It’s called, “Sylvia’s Super-Awesome Project Book: Super Simple Arduino!” The book is a fun and colorful introduction to Arduino microcontrollers and programming, written and illustrated by kid engineer Super-Awesome Sylvia. It has 3 great projects to get started on an Arduino adventure, plus lots of ideas and resources for even more...

The BMD-34 series are advanced, highly flexible, ultralow-power multiprotocol modules that enable concurrent Bluetooth® 5, Thread and Zigbee (IEEE 802.15.4) connectivity for portable, extremely low...

The BMD-34 series are advanced, highly flexible, ultralow-power multiprotocol modules that enable concurrent Bluetooth® 5, Thread and Zigbee (IEEE 802.15.4) connectivity for portable, extremely low power embedded systems, offering the greatest radio range and coverage. With an Arm® Cortex®‑M4 with FPU, integrated 2.4 GHz transceiver, an extended range of interfaces and embedded hardware cryptographic engine, the BMD-34 modules provide a complete RF solution allowing faster time to market with...

Surface mount DPDT switch for those tight portable designs. Capable of switching up to 1.2VA (360mA at 3.3V and 240mA at 5V). Documents: Datasheet ...

Surface mount DPDT switch for those tight portable designs. Capable of switching up to 1.2VA (360mA at 3.3V and 240mA at 5V). Documents: Datasheet

Surface mount 3-way switch. These switches are commonly found on handheld devices like MP3 players. This switch allows the user to navigate using up and down selections then select by pressing the...

Surface mount 3-way switch. These switches are commonly found on handheld devices like MP3 players. This switch allows the user to navigate using up and down selections then select by pressing the plastic piece inwards. Capable of swtiching up to 1.2VA (360mA at 3.3V and 240mA at 5V). Documents: Datasheet (Thanks, Roboteernat!) ...

Surface Mount Navigation Switch BreakoutDescription: This is a fully assembled simple breakout board for the surface mount 3-way switch. These switches are commonly found on handheld devices like...

Surface Mount Navigation Switch BreakoutDescription: This is a fully assembled simple breakout board for the surface mount 3-way switch. These switches are commonly found on handheld devices like MP3 players. This switch allows the user to navigate using up and down selections then select by pressing the plastic piece inwards. Capable of swtiching up to 1.2VA (360mA at 3.3V and 240mA at 5V).Documents: OS-1305.pdf ...

A simple SMD slide switch. Perfect for when you need access to a setting or a power switch from the edge of a PCB buried deep within a project. Features: 4V - 300mA 70mOhm resistance 10,000 cycle...

A simple SMD slide switch. Perfect for when you need access to a setting or a power switch from the edge of a PCB buried deep within a project. Features: 4V - 300mA 70mOhm resistance 10,000 cycle life Documents: Datasheet

Surface transducers give you the awesome power to turn almost any surface into a speaker. They're essentially just a speaker except instead of a cone, the coil is attached to a pad that conducts the...

Surface transducers give you the awesome power to turn almost any surface into a speaker. They're essentially just a speaker except instead of a cone, the coil is attached to a pad that conducts the vibration into whatever you press it against. Hook it up to an audio source and press it against the nearest table, wall or cardboard box. You can even put it against your head and play music directly into your skull (the ultimate surround sound). This transducer comes with an adhesive magnet that...

This is a 150mm (~6") long, 10-conductor cable that's especially ideal for many JTAG applications. Both ends are terminated with 2x5 pin female connectors with 1.27mm (0.05") spacing. Documents:...

This is a 150mm (~6") long, 10-conductor cable that's especially ideal for many JTAG applications. Both ends are terminated with 2x5 pin female connectors with 1.27mm (0.05") spacing. Documents: Datasheet

The BAV99 is a 350mW high-speed switching diode array with series-pair diode configuration. It achieves high-current conductivity, up to 200mA, in a very small 7mm2 footprint. Features: Diode...

The BAV99 is a 350mW high-speed switching diode array with series-pair diode configuration. It achieves high-current conductivity, up to 200mA, in a very small 7mm2 footprint. Features: Diode Configuration: 1 Pair Series Connection Voltage - DC Reverse (Vr) (Max): 70 V Current - Average Rectified (Io) (per Diode): 200mA Voltage - Forward (Vf) (Max) @ If: 1.25 V @ 150 mA Speed: Small Signal = Reverse Recovery Time (trr): 6 ns Current - Reverse Leakage @ Vr: 2.5 µA @ 70 V Operating Temperature -...

"This is Sylvia’s Super Awesome Kit, a companion kit for Sylvia’s Super-Awesome Project Book: Super Simple Arduino! With this kit you will be able to follow along with the book and...

"This is Sylvia’s Super Awesome Kit, a companion kit for Sylvia’s Super-Awesome Project Book: Super Simple Arduino! With this kit you will be able to follow along with the book and create three great projects to get started on an Arduino adventure! A lot of work has gone into the Super-Awesome Project Book, and we wanted to make it as easy as possible to get the three projects in this book started. The book, written by Super-Awesome Sylvia, star of Super-Awesome Sylvia’s...

The SyRen motor driver is one of the most versatile, efficient and easy to use motor drivers on the market. It is suitable for medium powered robots - up to 30lbs in combat or 100lbs for general...

The SyRen motor driver is one of the most versatile, efficient and easy to use motor drivers on the market. It is suitable for medium powered robots - up to 30lbs in combat or 100lbs for general purpose robotics. Out of the box, the SyRen 10 can supply a single DC brushed motor with up to 10A continuously. Peak currents of 15A are achievable for a few seconds. Overcurrent and thermal protection means you'll never have to worry about killing the driver with accidental stalls or by hooking up...

The SyRen motor driver is one of the most versatile, efficient and easy to use motor drivers on the market. It is suitable for medium powered robots - up to 50lbs in combat or 180lbs for general...

The SyRen motor driver is one of the most versatile, efficient and easy to use motor drivers on the market. It is suitable for medium powered robots - up to 50lbs in combat or 180lbs for general purpose robotics. Out of the box, the SyRen 25 can supply a single DC brushed motor with up to 25A continuously. Peak currents of 45A are achievable for a few seconds. Overcurrent and thermal protection means you'll never have to worry about killing the driver with accidental stalls or by hooking up...

The SyRen motor driver is one of the most versatile, efficient and easy to use motor drivers on the market. Out of the box, the SyRen 50 can supply a single DC brushed motor with up to 50A...

The SyRen motor driver is one of the most versatile, efficient and easy to use motor drivers on the market. Out of the box, the SyRen 50 can supply a single DC brushed motor with up to 50A continuously. Peak currents of 100A are achievable for a few seconds. Overcurrent and thermal protection means you'll never have to worry about killing the driver with accidental stalls or by hooking up too big a motor. With just one SyRen driver you can control a motor with: analog voltage, radio control,...

This is an SMD 12mm square SPST button. What we really like is the large button head and good tactile feel (it ‘clicks’ really well). This button is great for user input or a good reset button on a...

This is an SMD 12mm square SPST button. What we really like is the large button head and good tactile feel (it ‘clicks’ really well). This button is great for user input or a good reset button on a PCB, heck, we use this guy on our PicoBoard! As this is an SMD component make sure you are well versed in soldering before attempting to incorporate this button into your project. Documents: Datasheet ...

This is an SMD 6mm square SPST button. What we really like is the little button head and good tactile feel (it ‘clicks’ really well). This button is great for user input or a good reset button on a...

This is an SMD 6mm square SPST button. What we really like is the little button head and good tactile feel (it ‘clicks’ really well). This button is great for user input or a good reset button on a PCB. As this is an SMD component make sure you are well versed in soldering before attempting to incorporate this button into your project. Documents: [Dimensional Drawing](https://cdn.sparkfun.com/datasheets/Components/Switches/COM-12922_datasheet SW-033.jpg) ...

These tactile buttons are great for all sorts of projects. This assortment comes with 2 of each of 6 different colors for a total of 12 buttons. The colored caps are removable and the buttons fit...

These tactile buttons are great for all sorts of projects. This assortment comes with 2 of each of 6 different colors for a total of 12 buttons. The colored caps are removable and the buttons fit into breadboards. See the drawing below for exact dimensions. Documents: Drawing

This 2x20 pin female header is meant to allow you to extend the reach of any board with the standard 2x20 GPIO pin footprint like the Raspberry Pi, Google Coral, and NVIDIA Jetson. You can also...

This 2x20 pin female header is meant to allow you to extend the reach of any board with the standard 2x20 GPIO pin footprint like the Raspberry Pi, Google Coral, and NVIDIA Jetson. You can also solder it to Pi HATs that do not have headers on the board. This is assuming that the board is only populated on the top of the board or the height of the components do not get in the way if it is a two layer board. Features: Dimensions: 51.35mm L x 18.95mm T x 4.93mm W. Black section is 8.48mm T ...

Taoglas AA.200 MagmaX2 Multiband GNSS Magnetic Mount Antenna is for use across most major constellations including GPS (L1/L2/L5), GLONASS (G1/G2/G5), Galileo(E1/E5a/E5b) and BeiDou(B1/B2). AA.200...

Taoglas AA.200 MagmaX2 Multiband GNSS Magnetic Mount Antenna is for use across most major constellations including GPS (L1/L2/L5), GLONASS (G1/G2/G5), Galileo(E1/E5a/E5b) and BeiDou(B1/B2). AA.200 antenna is an active multiband GNSS magnetic mount antenna that exhibits excellent gain and good radiation pattern stability. The combination of these elements help ensure the best possible positional accuracy for systems where RTK is enabled and disabled. Taoglas AA.200 MagmaX2 Multiband GNSS...

What is a stepper motor? Stepper motor is a brushless DC electric motor that divides a full rotation into a number of equal steps The motor's position can then be commanded to move and hold at one...

What is a stepper motor? Stepper motor is a brushless DC electric motor that divides a full rotation into a number of equal steps The motor's position can then be commanded to move and hold at one of these steps. How to control a stepper motor?The fast way to control a stepper motor is just using a stepper motor driver (controller). And TB6600 arduino is just what you need.TB6600 arduino is an easy-to-use professional stepper motor driver, which could control a two-phase stepping motor. It is...

Spin two DC motors, step one bi-polar or uni-polar stepper, or fire off two solenoids with 1.2A per channel using the TB6612. We really like these dual H-bridges, so if you want to control motors...

Spin two DC motors, step one bi-polar or uni-polar stepper, or fire off two solenoids with 1.2A per channel using the TB6612. We really like these dual H-bridges, so if you want to control motors without a shield or HAT these are easy to include on any solderless breadboard or perma-proto. We solder on TB6612 onto a breakout board for you here, with a polarity protection FET on the motor voltage input and a pullup on the "standby" enable pin. Each breakout chip contains two full H-bridges...

This is an Arduino RGB Color Sensor breakout uses TAOS TCS3200 RGB sensor chip and 4 white LEDs. The TCS3200 arduino color sensor can detect and measure a nearly limitless range of visible colors....

This is an Arduino RGB Color Sensor breakout uses TAOS TCS3200 RGB sensor chip and 4 white LEDs. The TCS3200 arduino color sensor can detect and measure a nearly limitless range of visible colors. Applications include test strip reading, sorting by color, ambient light sensing and calibration, and color matching, to name just a few. The TCS3200 has an array of photodetectors, each with either a red, green, or blue filter, or no filter (clear). The filters of each color are distributed evenly...

After tens of millions of years of evolution, chameleons have formed a biological instinct where they can change the color of their skin to match their environment. This technique has enabled them...

After tens of millions of years of evolution, chameleons have formed a biological instinct where they can change the color of their skin to match their environment. This technique has enabled them to avoid detection from predators.We have taken inspiration from nature to develop the TCS34725 I2C Color Sensor. Using optical techniques, this sensor detects colors in its surrounding environment and provides a digital return of red, green, blue (RGB) values. This enables you to then recreate the...

This is the Teensy 4 Audio Shield (Rev D) that can be added to a Teensy 4.0 for your next audio project. The shield provides you with an easy-to-use tool to add high quality 16 bit, 44.1 kHz sample...

This is the Teensy 4 Audio Shield (Rev D) that can be added to a Teensy 4.0 for your next audio project. The shield provides you with an easy-to-use tool to add high quality 16 bit, 44.1 kHz sample rate audio to your Teensy. With the audio library provided in the Documents tab, you will be able to use both the input and output simultaneously in order to make a variety of great audio projects, incorporate synth waveforms, effects, and mix multiple sound streams and CD quality audio to your...

This is the Teensy 4 Audio Shield (Rev D2) that can be added to a Teensy 4.0 for your next audio project. The shield provides you with an easy-to-use tool to add high quality 16 bit, 44.1 kHz sample...

This is the Teensy 4 Audio Shield (Rev D2) that can be added to a Teensy 4.0 for your next audio project. The shield provides you with an easy-to-use tool to add high quality 16 bit, 44.1 kHz sample rate audio to your Teensy. With the audio library provided in the Documents tab, you will be able to use both the input and output simultaneously in order to make a variety of great audio projects, incorporate synth waveforms, effects, and mix multiple sound streams and CD quality audio to your...

Teensy 4.0 features an ARM Cortex-M7 processor at 600MHz, with a NXP iMXRT1062 chip, the fastest microcontroller available today. Teensy 4.0 is the same size and shape as Teensy 3.2, and retains...

Teensy 4.0 features an ARM Cortex-M7 processor at 600MHz, with a NXP iMXRT1062 chip, the fastest microcontroller available today. Teensy 4.0 is the same size and shape as Teensy 3.2, and retains compatibility with most of the pin functions on Teensy 3.2. When running at 600 MHz, Teensy 4.0 consumes approximately 100mA current. Teensy 4.0 provides support for dynamic clock scaling. Unlike traditional microcontrollers, where changing the clock speed causes wrong baud rates and other issues,...

Teensy 4.0 features an ARM Cortex-M7 processor at 600MHz, with a NXP iMXRT1062 chip, the fastest microcontroller available today. Teensy 4.0 is the same size and shape as Teensy 3.2, and retains...

Teensy 4.0 features an ARM Cortex-M7 processor at 600MHz, with a NXP iMXRT1062 chip, the fastest microcontroller available today. Teensy 4.0 is the same size and shape as Teensy 3.2, and retains compatibility with most of the pin functions on Teensy 3.2. The best part of this version of Teensy 4.0 is that it includes headers already attached. No soldering is required allowing you to get started as quickly as possible! When running at 600 MHz, Teensy 4.0 consumes approximately 100mA current....

The Teensy 4.1 is the newest iteration of the astoundingly popular development platform that features an ARM Cortex-M7 processor at 600MHz, with a NXP iMXRT1062 chip, four times larger flash memory...

The Teensy 4.1 is the newest iteration of the astoundingly popular development platform that features an ARM Cortex-M7 processor at 600MHz, with a NXP iMXRT1062 chip, four times larger flash memory than the 4.0, and two new locations to optionally add more memory. The Teensy 4.1 is the same size and shape as the Teensy 3.6 (2.4in by 0.7in), and provides greater I/O capability, including an ethernet PHY, SD card socket, and USB host port. When running at 600 MHz, the Teensy 4.1 consumes...

The Teensy 4.1 is the newest iteration of the astoundingly popular development platform that features an ARM Cortex-M7 processor at 600MHz, with a NXP iMXRT1062 chip, four times larger flash memory...

The Teensy 4.1 is the newest iteration of the astoundingly popular development platform that features an ARM Cortex-M7 processor at 600MHz, with a NXP iMXRT1062 chip, four times larger flash memory than the 4.0, and two new locations to optionally add more memory. The Teensy 4.1 is the same size and shape as the Teensy 3.6 (2.4in by 0.7in), and provides greater I/O capability, including an ethernet PHY, SD card socket, and USB host port. The best part of this version of Teensy 4.1 is that it...

The Teensy 4.1 is the newest iteration of the astoundingly popular development platform that features an ARM Cortex-M7 processor at 600MHz, with a NXP iMXRT1062 chip, four times larger flash memory...

The Teensy 4.1 is the newest iteration of the astoundingly popular development platform that features an ARM Cortex-M7 processor at 600MHz, with a NXP iMXRT1062 chip, four times larger flash memory than the 4.0, and two new locations to optionally add more memory. The Teensy 4.1 is the same size and shape as the Teensy 3.6 (2.4in by 0.7in), and provides greater I/O capability, including an SD card socket, and USB host port. Please keep in mind that this Teensy 4.1 does not have Ethernet...

The Teensy 4.1 is the newest iteration of the astoundingly popular development platform that features an ARM Cortex-M7 processor at 600MHz, with a NXP iMXRT1062 chip, four times larger flash memory...

The Teensy 4.1 is the newest iteration of the astoundingly popular development platform that features an ARM Cortex-M7 processor at 600MHz, with a NXP iMXRT1062 chip, four times larger flash memory than the 4.0, and two new locations to optionally add more memory. The Teensy 4.1 is the same size and shape as the Teensy 3.6 (2.4in by 0.7in), and provides greater I/O capability, including an SD card socket, and USB host port. The best part of this version of Teensy 4.1 is that it includes...

The Teensy is an amazing and compact development platform in a breadboard friendly form factor, but what if you could incorporate it into the Arduino architecture? The Teensy Arduino Shield Adapter...

The Teensy is an amazing and compact development platform in a breadboard friendly form factor, but what if you could incorporate it into the Arduino architecture? The Teensy Arduino Shield Adapter allows you to attach your Teensy and utilize your favorite Arduino shields without the requirement of a breadboard or any complicated wiring. Needless to say, the Teensy Arduino Shield Adapter is a useful tool for upgrading all of your existing Arduino projects to a more powerful controller! As we...

These headers are made to work with the Teensy 4.0, Teensy 3.2, and Teensy LC development boards. Each kit of headers makes your Teensy breadboard compatible and will allow for stacking a Teensy and...

These headers are made to work with the Teensy 4.0, Teensy 3.2, and Teensy LC development boards. Each kit of headers makes your Teensy breadboard compatible and will allow for stacking a Teensy and Teensy-compatible shield board. This kit includes five headers (two 13-pin, one 7-pin, one 3-pin, and one 2x7 right-angle SMT), enough to connect your chosen Teensy in any configuration you need! Note: This Header Kit can also be used for the Teensy 3.0 and 3.1, as the pin layout has not changed...

This low-cost (LC) Teensy Prop Shield is meant for making light and sound effects on small, handheld props and wearable costumes. This shield features a 2W audio amp, high-speed 5V buffers for...

This low-cost (LC) Teensy Prop Shield is meant for making light and sound effects on small, handheld props and wearable costumes. This shield features a 2W audio amp, high-speed 5V buffers for driving APA102 LEDs, and an 8MB flash memory. This economical board is approximately the size of a Teensy, just slightly longer to allow space for mounting holes and connections for power, speaker and LEDs. This lower-cost Prop Shield is identical to the standard Prop Shield, except the motion sensors...

These headers are made to work with the Teensy 4.1, Teensy 3.6, and Teensy 3.5 development boards. Each set of headers allows for your Teensy to be easily incorporated into a breadboard circuit or...

These headers are made to work with the Teensy 4.1, Teensy 3.6, and Teensy 3.5 development boards. Each set of headers allows for your Teensy to be easily incorporated into a breadboard circuit or attach a shield on top of the board. This kit includes three headers (two 24-pin, and one 5-pin), enough to connect your chosen Teensy in any configuration you need! Includes: 2x 24-pin Stackable Header 1x 5-pin Stackable Header Documents: Dimensional Drawings ...

For beginners to Arduino it can be daunting and risky to wire LCD driver circuits - one wrong connection and your component can be damaged. This LCD expansion board removes all the complications and...

For beginners to Arduino it can be daunting and risky to wire LCD driver circuits - one wrong connection and your component can be damaged. This LCD expansion board removes all the complications and risks.The TELEMATICS 3.5" TFT Touch LCD Shield is an Arduino compatible display designed by DFRobot, with a resolution of 320x480, three serial ports and one IIC interface. It is perfectly compatible with Arduino DUE, Mega1280/2560, and Bluno Mega1280/2560. There is an on-board voltage switch which...

This ANT700 is a telescopic antenna designed for operation from 300 MHz to 1.1 GHz with a total length that is configurable from 9.5 cm to 24.5 cm. Each ANT700 is constructed of stainless steel and...

This ANT700 is a telescopic antenna designed for operation from 300 MHz to 1.1 GHz with a total length that is configurable from 9.5 cm to 24.5 cm. Each ANT700 is constructed of stainless steel and features an SMA male connector, rotating shaft, and adjustable elbow. The ANT700 is a 50 Ohm antenna designed to match HackRF One. It is the perfect first antenna for general purpose use with HackRF One, but we won't stop you from using it with different projects! Documents: Product Page ...

This ANT500 is a telescopic antenna designed for operation from 75 MHz to 1 GHz with a total length that is configurable from 20 cm to 88 cm long. Each ANT500 is constructed of stainless steel and...

This ANT500 is a telescopic antenna designed for operation from 75 MHz to 1 GHz with a total length that is configurable from 20 cm to 88 cm long. Each ANT500 is constructed of stainless steel and features an SMA male connector, rotating shaft, and adjustable elbow. The ANT500 is a 50 ohm antenna designed to match HackRF One. It is the perfect first antenna for general purpose use with HackRF One but we won't stop you from using it with different projects! Documents: Product Page Product Video ...

    This is a temprature controlled relay, you can set the relay on/off when the temprature is higher/lower than the temprature you set.The peak voltage capability is up to 250V...

    This is a temprature controlled relay, you can set the relay on/off when the temprature is higher/lower than the temprature you set.The peak voltage capability is up to 250V at 10A when AC and 30V at 10A when DC. With this module, it will be much more easyto implement applications that needs auto power up/down with the temprature varies.     Adjust the on-board potentiometer to adjust the sensitivity. The relay and the signal indicate LED would...

This sealed digital temperature probe lets you precisely measure temperatures in wet environments with a simple 1-Wire interface. The DS18B20 provides 9 to 12-bit (configurable) temperature readings...

This sealed digital temperature probe lets you precisely measure temperatures in wet environments with a simple 1-Wire interface. The DS18B20 provides 9 to 12-bit (configurable) temperature readings over a 1-Wire interface, so that only one wire (and ground) needs to be connected from a central microprocessor. Power for reading, writing, and performing temperature conversions can be derived from the data line itself with no need for an external power source. Because each DS18B20 contains a...

This is the same temperature sensor that is included in our SparkFun Inventor's Kit. The TMP36 is a low voltage, precision centigrade temperature sensor. It provides a voltage output that is...

This is the same temperature sensor that is included in our SparkFun Inventor's Kit. The TMP36 is a low voltage, precision centigrade temperature sensor. It provides a voltage output that is linearly proportional to the Celsius temperature. It also doesn't require any external calibration to provide typical accuracies of ±1°C at +25°C and ±2°C over the −40°C to +125°C temperature range. We like it because it's so easy to use: Just give the device a ground and 2.7 to 5.5 VDC and read the...

This sealed digital temperature probe lets you precisely measure temperatures in wet environments with a simple 1-Wire interface. The DS18B20 provides 9 to 12-bit (configurable) temperature readings...

This sealed digital temperature probe lets you precisely measure temperatures in wet environments with a simple 1-Wire interface. The DS18B20 provides 9 to 12-bit (configurable) temperature readings over a 1-Wire interface, so that only one wire (and ground) needs to be connected from a central microprocessor. Note: The pinout for this sensor is as follows: RED=Vcc BLACK=GND WHITE=SIG Features: 3.0-5.5V input voltage Waterproof -55°C to+125°C temperature range ±0.5°C accuracy from -10°C to...

The 4-Bay T4s Intelligent Universal Charger from Tenergy is an automatic smart charger compatible with almost all types of rechargeable batteries, thereby eliminating the need to own multiple...

The 4-Bay T4s Intelligent Universal Charger from Tenergy is an automatic smart charger compatible with almost all types of rechargeable batteries, thereby eliminating the need to own multiple chargers. Capable of automatically identifying and charging Lithium Ion (Li-ion), LiFePO4, NiMH and NiCD rechargeable batteries, the T4s applies the appropriate charging mode, whether it be a constant charge current (CC), constant charge voltage (CV) or trickle charge. The T4s is able to independently...

This 6 position screw terminal block provides a simple way to connect wires to a single connection point. These blocks allow wires to be screwed together and self-isolated without needing to twist,...

This 6 position screw terminal block provides a simple way to connect wires to a single connection point. These blocks allow wires to be screwed together and self-isolated without needing to twist, solder or any other splicing, by this method wiring can adjusted at anytime just as easy as it was the first time. Each 6 position block offers a screw pitch of 10mm with a max current of 15A and a max voltage tolerance of 600V before risking meltdown or implosion. Documents: Dimensional Drawing...

The TFMini Plus is a ToF (Time of Flight) LiDAR sensor capable of measuring the distance to an object as close as 10 centimeters (+/- 5cm up to 6m) and as far as 12 meters (+/-1% starting at 6m)! As...

The TFMini Plus is a ToF (Time of Flight) LiDAR sensor capable of measuring the distance to an object as close as 10 centimeters (+/- 5cm up to 6m) and as far as 12 meters (+/-1% starting at 6m)! As with all LiDAR sensors, your effective detection distance will vary depending on lighting conditions and the reflectivity of your target object, but what makes this sensor special is its size. Measuring only 35x18.5x21mm, the TFMini Plus allows you to integrate LiDAR into applications traditionally...

The TFMini-S Micro LiDAR Module is a ToF (Time of Flight) LiDAR sensor capable of measuring the distance to an object as close as 10 centimeters (+/- 6cm up to 6m) and as far as 12 meters (+/-1%...

The TFMini-S Micro LiDAR Module is a ToF (Time of Flight) LiDAR sensor capable of measuring the distance to an object as close as 10 centimeters (+/- 6cm up to 6m) and as far as 12 meters (+/-1% starting at 6m)! As with all LiDAR sensors, your effective detection distance will vary depending on lighting conditions and the reflectivity of your target object, but what makes this sensor special is its size. Measuring only 42x15x16mm, the TFMini-S allows you to integrate LiDAR into applications...

The Arduino microcontroller makes it easy to learn about electronics, but it can be hard to know where to start. The 10 projects in "The SparkFun Arduino Inventor's Guide" will teach you to build,...

The Arduino microcontroller makes it easy to learn about electronics, but it can be hard to know where to start. The 10 projects in "The SparkFun Arduino Inventor's Guide" will teach you to build, code and invent with the super-smart Arduino and a handful of parts. First, you’ll master the basics with a primer that explains how a circuit works, how to read a wiring schematic, and how to build and test projects with a solderless breadboard. Then you’ll learn how to make your hardware move,...

Processing is a free, beginner-friendly programming language designed to help non-programmers create interactive art with code. In Processing, you can make a masterpiece with just a simple program,...

Processing is a free, beginner-friendly programming language designed to help non-programmers create interactive art with code. In Processing, you can make a masterpiece with just a simple program, and at the click of a button, the software displays your handiwork on-screen for instant feedback. The SparkFun Guide to Processing teaches you to craft your own digital artwork and even combine it with hardware—no prior programming experience required. Over the course of the book, you’ll learn the...

Thermally Conductive Adhesive Transfer Tapes are designed to provide a preferential heat-transfer path between heat-generating components and heat sinks or other cooling devices (e.g., fans, heat...

Thermally Conductive Adhesive Transfer Tapes are designed to provide a preferential heat-transfer path between heat-generating components and heat sinks or other cooling devices (e.g., fans, heat spreaders or heat pipes). This is a 4x4" square, 0.2mm thickness piece of thermal tape. Features: 4x4" square 0.2mm thickness

10K thermistor with a negative temperature coefficient. Good choice for temp-sensing applications when you need a reliable NTC thermistor. Vishay part #: NTCLE100E3103JB0 Note: You get only one...

10K thermistor with a negative temperature coefficient. Good choice for temp-sensing applications when you need a reliable NTC thermistor. Vishay part #: NTCLE100E3103JB0 Note: You get only one thermistor. **Document: ** Datasheet Bildr Tutorial

This Thermocouple Connector is perfect for bridging the gap between Type-K thermocouples with standard connectors with a PCB. This little connector is actually the exact part we recommend using with...

This Thermocouple Connector is perfect for bridging the gap between Type-K thermocouples with standard connectors with a PCB. This little connector is actually the exact part we recommend using with our SparkFun Thermocouple Breakout! Each connector can easily attach to a printed circuit board with its included mounting clip. If you plan on using this connector with a custom PCB make sure to check out the Datasheet in the Documents section below for mounting dimensions. Documents:...

This Thermocouple Connector is perfect for bridging the gap between Type-K thermocouples with standard connectors with a PCB. Each connector can easily attach to a printed circuit board with its...

This Thermocouple Connector is perfect for bridging the gap between Type-K thermocouples with standard connectors with a PCB. Each connector can easily attach to a printed circuit board with its included mounting clip. Once we are out of stock, we will not carry it again. Get them while you can! Documents: Datasheet ...

36" high temperature Type-K Thermocouple with glass braid insulation. Features: Type-K Thermocouple (Ni-Cr) 30 gauge stripped and prepped wires Thermocouple range : -270 to +1372C (-454 to...

36" high temperature Type-K Thermocouple with glass braid insulation. Features: Type-K Thermocouple (Ni-Cr) 30 gauge stripped and prepped wires Thermocouple range : -270 to +1372C (-454 to +2501F) Glass braid insulation range : -73 to +482C(-100 to +900F) Yellow + / Red - Works great with our Thermocouple Amplifier AD595 IC!

This is a stainless steel, Type-K Thermocouple probe. A thermocouple works by taking two wires made of dissimilar metals, connecting them at the two ends, and making a temperature gradient between...

This is a stainless steel, Type-K Thermocouple probe. A thermocouple works by taking two wires made of dissimilar metals, connecting them at the two ends, and making a temperature gradient between one end and the other (a 'hot' end and a 'cold' one). Once this is achieved, a voltage potential is formed and current flows. One junction is held in the environment where the temperature of interest exists, this is known as the hot junction. The other junction, referred to as the cold junction, can...

    The fiber optic Temperature Probe TP-01 is a high precision temperature probe for use in a wide temperature range. It is for the temprature measuring of air/solid, but not...

    The fiber optic Temperature Probe TP-01 is a high precision temperature probe for use in a wide temperature range. It is for the temprature measuring of air/solid, but not for liquid. It is a point-like probe housed in a stainless steel tube and with a connector at one end. you can also find the Thermocouple_K_Female Connetor to integrate this sensor to your PCBA Features Length:100cm Measuring Range:-50 - +400 response time: 5s ...

Thermoelectric coolers (TEC or Peltier) create a temperature differential on each side. One side gets hot and the other side gets cool. Therefore, they can be used to either warm something up or...

Thermoelectric coolers (TEC or Peltier) create a temperature differential on each side. One side gets hot and the other side gets cool. Therefore, they can be used to either warm something up or cool something down, depending on which side you use. You can also take advantage of a temperature differential to generate electricity. The thermal tape listed below works very well to attach heat sinks to the hot side. This Peltier works very well as long as you remove the heat from the hot side....

If you want to get some sound out of your project but have a tight space budget, this is a good way to do it. This 0.5W, 8Ohm speaker is only 40mm in diameter and just over 4mm thick, the same kind...

If you want to get some sound out of your project but have a tight space budget, this is a good way to do it. This 0.5W, 8Ohm speaker is only 40mm in diameter and just over 4mm thick, the same kind you might find in one of those "talking greeting cards". Documents: Datasheet Dimensional Drawing ...

If you want to get some sound out of your project but have a tight space budget, this is a good way to do it. This 2.5W, 4 Ohm speaker is only 28mm in diameter and just over 4mm thick. The cable is...

If you want to get some sound out of your project but have a tight space budget, this is a good way to do it. This 2.5W, 4 Ohm speaker is only 28mm in diameter and just over 4mm thick. The cable is roughly 180mm long and terminates in a 2-wire JST connector.

This is a solderer's best helper, the third hand. Comes with a heavy base, two alligator clips, a soldering iron holder, and a good magnifying glass. Note that we don't normally need a third hand....

This is a solderer's best helper, the third hand. Comes with a heavy base, two alligator clips, a soldering iron holder, and a good magnifying glass. Note that we don't normally need a third hand. It's nice, but soldering flat on a table works just fine. Then again, the desk is starting to look like a mine field of burn marks and melted pot holes. What we've found with many of these cheaper third hand is the lack of stability. The small base on this unit does not make the problem any better....

A 3-phase DC brushless DC motor has the unique capability of being both a high efficiency, high torque, very smooth motor, as well as the starting point for haptic feedback when combined with the...

A 3-phase DC brushless DC motor has the unique capability of being both a high efficiency, high torque, very smooth motor, as well as the starting point for haptic feedback when combined with the appropriate sensor and motor control. For an excellent demonstration of what's possible with 3-phase DC motors, checkout Scott Bezek's SmartKnob. Connector: Molex 51021-0300 Mating connector: 053048-0310 (PTH R/A), or 053047-0310 (PTH), or 053261-0371 (SMD) Documents: EM3215 3-Phase Brushless DC Motor...

This is a small 15mm round speaker that operates around the audible 2kHz range. You can use these speakers to create simple music or user interfaces. This through-hole speaker is great for projects...

This is a small 15mm round speaker that operates around the audible 2kHz range. You can use these speakers to create simple music or user interfaces. This through-hole speaker is great for projects where you don't have room for a full-blown speaker. This 15mm diameter speaker is encased in plastic and will handle up to 0.5W of power. Features: Diameter 15 mm Depth 7.5 mm Input Power: Min. 0.3W, Max. 0.5W Impedance at 3 kHz, 1 V: Min. 6.8Ω, Typ. 8Ω, Max. 9.2Ω Resonant Frequency at 1V: Min....

This is a joystick very similar to the 'analog' joysticks on PS2 (PlayStation 2) controllers. Directional movements are simply two potentiometers - one for each axis. Pots are ~10k each. This...

This is a joystick very similar to the 'analog' joysticks on PS2 (PlayStation 2) controllers. Directional movements are simply two potentiometers - one for each axis. Pots are ~10k each. This joystick also has a select button that is actuated when the joystick is pressed down. Note: Breakout board available below. Documents: Tutorial Eagle Library Videos ...

This is a 16mm deluxe thumb joystick and is very similar to the 'analog' joysticks found inside PlayStation controllers. Directional movements are provided simply by two potentiometers - one for...

This is a 16mm deluxe thumb joystick and is very similar to the 'analog' joysticks found inside PlayStation controllers. Directional movements are provided simply by two potentiometers - one for each axis. These 10k potentiometers will read the position changes for the joystick's full range of physical motion. This joystick also has a select button that is actuated when the joystick is pressed down. The mechanical parts found in this joystick are mostly metal and are considered far sturdier...