Overview It is the black metal panel that is installed on the back of the P1S printer (Please use the original screws from the printer for black metal rear pannel installation, as there are no...

Overview It is the black metal panel that is installed on the back of the P1S printer (Please use the original screws from the printer for black metal rear pannel installation, as there are no screws included in the package of this spare part). Installation Learn more about the replacement of the Rear Metal Panel for P1 Series on Bambu Lab Wiki. In the Box - Rear Metal Panel*1 ...

This Relay Shield v2.0 from Evil Mad Scientist is a simple Arduino add-on that gives your Arduino the ability to control a single electromechanical relay for switching loads of up to 24VDC or 40VAC....

This Relay Shield v2.0 from Evil Mad Scientist is a simple Arduino add-on that gives your Arduino the ability to control a single electromechanical relay for switching loads of up to 24VDC or 40VAC. Each Relay Shield comes equipped with a single pole - double throw (SPDT) sealed relay which can handle a current load of up to 5A. This means that when current is applied to the coil it throws a simple changeover switch, terminating the connection from the NC (Normally Closed) contact to ground...

These are high quality Single Pole - Double Throw (SPDT) sealed relays. Use them to switch high voltage, and/or high current devices. This relay's coil is rated up to 12V, with a minimum switching...

These are high quality Single Pole - Double Throw (SPDT) sealed relays. Use them to switch high voltage, and/or high current devices. This relay's coil is rated up to 12V, with a minimum switching voltage of 5V. The contacts are rated up to 5A (@250VAC, 30VDC). Note: In the Datasheet below there is a pin layout listed as "Bottom View." Be aware, this pin layout is actually the top-down view NOT bottom-up. Features: 5V DC SPDT Relay Rated up to 5A Fully Sealed Documents: Datasheet ...

These are massive single pole - double throw (SPDT) sealed relays. This means that when current is applied to the coil it throws a simple changeover switch, terminating the connection from the NC...

These are massive single pole - double throw (SPDT) sealed relays. This means that when current is applied to the coil it throws a simple changeover switch, terminating the connection from the NC contact to ground and closing the NO contact. Use them to switch high voltage/high current devices. Features: SPDT Relay Contacts Rated up to 220VAC @ 20A Coil Voltage: 5V Fully Sealed Documents: Datasheet (JQX-15F/005) Relay Tutorial ...

1/6th Watt, +/- 5% tolerance PTH resistors. Commonly used in breadboards and perf boards, these 1.0M resistors make excellent pull-ups, pull-downs, and current limiters. Note: Although these come in...

1/6th Watt, +/- 5% tolerance PTH resistors. Commonly used in breadboards and perf boards, these 1.0M resistors make excellent pull-ups, pull-downs, and current limiters. Note: Although these come in bags marked with a quantity of 25, they don't always contain 25. So we'd rather call it 20 and hope that you get extras. Documents: Breadboard Lecture Sensor Interfacing Voltage Dividers ...

These are your standard issue USB 2.0 type A to micro USB 5-pin... but wait, what's this? These cables have minor, yet genius modifications that allow both ends to be plugged into their ports...

These are your standard issue USB 2.0 type A to micro USB 5-pin... but wait, what's this? These cables have minor, yet genius modifications that allow both ends to be plugged into their ports regardless of their orientation. No longer will you fight the USB "super position" where both orientations of your plug seem incorrect. A simple solution to a problem that nearly everyone has faced. This is one of the features we love so much about USB-C, but now it works with all your Micro-B devices as...

These wireless receivers work with our 434MHz transmitters. They can easily fit into a breadboard and work well with microcontrollers to create a very simple wireless data link. Since these are only...

These wireless receivers work with our 434MHz transmitters. They can easily fit into a breadboard and work well with microcontrollers to create a very simple wireless data link. Since these are only receivers, they will only work communicating data one-way, you would need two pairs (of different frequencies) to act as a transmitter/receiver pair. Note: These modules are indiscriminate and will receive a fair amount of noise. Both the transmitter and receiver work at common frequencies and...

These wireless transmitters work with our 434MHz receivers. They can easily fit into a breadboard and work well with microcontrollers to create a very simple wireless data link. Since these are only...

These wireless transmitters work with our 434MHz receivers. They can easily fit into a breadboard and work well with microcontrollers to create a very simple wireless data link. Since these are only transmitters, they will only work communicating data one-way, you would need two pairs (of different frequencies) to act as a transmitter/receiver pair. Note: These modules are indiscriminate and will receive a fair amount of noise. Both the transmitter and receiver work at common frequencies and...

RFID (radio-frequency identification) is the wireless non-contact use of radio-frequency electromagnetic fields, for the purposes of identifying and tracking tags attached to objects. This is the...

RFID (radio-frequency identification) is the wireless non-contact use of radio-frequency electromagnetic fields, for the purposes of identifying and tracking tags attached to objects. This is the ID-12LA, a very simple to use RFID reader module from ID Innovations. With a built in antenna, the only holdup is the 2mm pin spacing. Power the module, hold up a 125kHz card, and get a serial string output containing the unique ID of the card. Note: The new ID-12LA is essentially the same as the...

This is the 915MHz base RFM69HCW Wireless Transceiver that is found on our RFM69 Breakout. The RFM69HCW is an inexpensive and versatile radio module that operates in the unlicensed ISM (Industry,...

This is the 915MHz base RFM69HCW Wireless Transceiver that is found on our RFM69 Breakout. The RFM69HCW is an inexpensive and versatile radio module that operates in the unlicensed ISM (Industry, Science and Medicine) band, a set of frequencies set aside for low-power, short-range, license-free radios. It’s perfect for building inexpensive short-range wireless networks of sensors and actuators for home automation, citizen science and more. This RFM69HCW module operates on the 915MHz frequency...

"This ZIF connector mates with the 6-conductor ribbon cable for the GP-2106 GPS module. Use it to roll your own GP-2106 carrier board! Documents: Datasheet (FH34SRJ-6S-0.5SH) " ...

"This ZIF connector mates with the 6-conductor ribbon cable for the GP-2106 GPS module. Use it to roll your own GP-2106 carrier board! Documents: Datasheet (FH34SRJ-6S-0.5SH) "

Overview It is the plastic panel that is installed on the right side of the printer when facing the screen of the printer. Installation Learn more about the replacement of the Right Plastic Panel...

Overview It is the plastic panel that is installed on the right side of the printer when facing the screen of the printer. Installation Learn more about the replacement of the Right Plastic Panel for P1 Series on Bambu Lab Wiki. Please note that the left and right side panels of the P1P may be incompatible with the base and require shaving off two tabs on the bottom of side panels for successful installation. Two types of bases for the P1P model We have two types of bases for the P1P model....

"The RN-XV module by Roving Networks is a certified Wi-Fi solution especially designed for customer who want to migrate their existing 802.15.4 architecture to a standard TCP/IP based platform...

"The RN-XV module by Roving Networks is a certified Wi-Fi solution especially designed for customer who want to migrate their existing 802.15.4 architecture to a standard TCP/IP based platform without having to redesign their existing hardware. In other words, if your project is set up for XBee and you want to move it to a standard WiFi network, you can drop this in the same socket without any other new hardware. The RN-XV module is based upon Roving Networks' robust RN-171 Wi-Fi module and...

This bundle includes the following items. 3 epoxy tooling material (rotary CNC) and 3 kraft cylinder (rotary laser) ...

This bundle includes the following items. 3 epoxy tooling material (rotary CNC) and 3 kraft cylinder (rotary laser)

An adjustable potentiometer can open up many interesting user interfaces. Turn the pot and the resistance changes. Connect VCC to an outer pin, GND to the other, and the center pin will have a...

An adjustable potentiometer can open up many interesting user interfaces. Turn the pot and the resistance changes. Connect VCC to an outer pin, GND to the other, and the center pin will have a voltage that varies from 0 to VCC depending on the rotation of the pot. Hook the center pin to an ADC on a microcontroller and get a variable input from the user! This pot has a 1/4" mounting diameter and has a 10K linear taper. Check the datasheet for dimensional drawings. Documents: Datasheet How...

This is a single pole, 10 position rotary switch able to select up to 10 different states in a durable package. Unlike our other rotary switch, this model is much more robust and capable of handling...

This is a single pole, 10 position rotary switch able to select up to 10 different states in a durable package. Unlike our other rotary switch, this model is much more robust and capable of handling larger currents and voltages. You may find this rotary switch familiar, it's the same one we trusted in our Decade Resistance Box! With a max voltage rating of 125VAC at 0.3A and a dielectric strength of 250VAC for 1 minute this is a serious little rotary switch capable of working with some of your...

Schottky diodes are known for their low forward voltage drop and a very fast switching action. This 1A 40V Schottky diode is ideal for use with motor drivers such as the L298N. Documents: Datasheet ...

Schottky diodes are known for their low forward voltage drop and a very fast switching action. This 1A 40V Schottky diode is ideal for use with motor drivers such as the L298N. Documents: Datasheet

Screw Terminals with 3.5mm pitch pins. Comes in 2, 3, or 4 positions and have the really cool feature of slide-locking together to form any size you need (4, 5, up to 20 without problems). Rated up...

Screw Terminals with 3.5mm pitch pins. Comes in 2, 3, or 4 positions and have the really cool feature of slide-locking together to form any size you need (4, 5, up to 20 without problems). Rated up to 125V @ 10A. Terminal can accept 16 to 26AWG wire. 3.5mm/138mil pin pitch will not fit standard 0.1" perf boards but this is the most common pitch screw terminal. Documents: Datasheet ...

    This is a 3 Pole 5.0mm Screw Terminal Block.It includes 5 units of Terminal Block.There are screws which are tightened for a secure connection for both lugs and bare wire....

    This is a 3 Pole 5.0mm Screw Terminal Block.It includes 5 units of Terminal Block.There are screws which are tightened for a secure connection for both lugs and bare wire. Specification Rated: 250,16A(250V,17.5A)Contact resistance: 200m? MaxInsulation resistance: 5000M? MinTemp range: -30?~+120?Max Soldering: +260? 5sWire range: 22-14AWG(1.5mm2)Strip length: 3.5mm      ...

The 4x4 Keypad is a general purpose 16 button (4x4) matrix keypad. It comes ready to work, simply peel-off the adhesive backing, stick it to your surface and plug it in. ...

The 4x4 Keypad is a general purpose 16 button (4x4) matrix keypad. It comes ready to work, simply peel-off the adhesive backing, stick it to your surface and plug it in.

This is your simple three conductor sensor cable with electrode pad leads. These cables are 24" long and feature a 3.5mm audio jack connector on one end with snap style receptacles for biomedical...

This is your simple three conductor sensor cable with electrode pad leads. These cables are 24" long and feature a 3.5mm audio jack connector on one end with snap style receptacles for biomedical sensor pads. Each cable comes in a red/blue/black set. Features: 24" Long 4 mm connector Documents: Product Video

    Arduino Sensor Shield V4.0 let us to build electronics projects just as easy as piling bricks. It can connect to various modules like sensors, servos, relays, buttons,...

    Arduino Sensor Shield V4.0 let us to build electronics projects just as easy as piling bricks. It can connect to various modules like sensors, servos, relays, buttons, potentiometers. Just plug & play.     Each functional module has buckled port with VCC, GND and Output, which has corresponding port on the Sensor Shield, connected with a plain 2.54mm dual-female cable you may start playing already. Buckled brick cables are like cement for bricks,...

Serial Connector - Ribbon Cable (Female, 9-pin) Description: DB9 connectors are a great way to make a tight connection on your project or to plug into existing serial lines. Now you can make...

Serial Connector - Ribbon Cable (Female, 9-pin) Description: DB9 connectors are a great way to make a tight connection on your project or to plug into existing serial lines. Now you can make your own DB9 cables the easy way with these crimp-on ribbon cable connectors. These work great with our 10-wire ribbon cable, you just need to peel back the one unneeded wire. Matching male connectors are available and can be found in the related items below. Includes: Male DB9 connector body Rear...

     This serial WiFi transceiver module is based on ESP8266 SoC.. ESP8266 is a highly integrated chip that has Integrated TCP/IP protocol stack. It offers a complete and...

     This serial WiFi transceiver module is based on ESP8266 SoC.. ESP8266 is a highly integrated chip that has Integrated TCP/IP protocol stack. It offers a complete and self-contained Wi-Fi networking solution, allowing it to either host the application or to offload all Wi-Fi networking functions from another application processor.      Besides, ESP8266 has powerful on-board processing and storage capabilities that allow it to be integrated with the...

Here is a simple, low-cost, high quality servo for all your mechatronic needs. This servo is very similar in size and specifications to the Hitec HS-55. This little guy is able to take in 6 volts...

Here is a simple, low-cost, high quality servo for all your mechatronic needs. This servo is very similar in size and specifications to the Hitec HS-55. This little guy is able to take in 6 volts and deliver 20.8 oz-in. of maximum torque at 0.10 sec/60° This small servo comes with a standard 3 pin power and control cable, and all hardware listed below. Note: This servo is rated for 180° rotation, but in actuality it only hits ~160°. Includes: 1x Micro Size Servo 1x Single Arm Micro Horn 1x...

Here, for all your mechatronic needs, is a simple, high quality continuous rotation servo motor. This servo is able to take in 6 volts and deliver 30.6 oz-in. of maximum torque at 0.14 sec/60° A...

Here, for all your mechatronic needs, is a simple, high quality continuous rotation servo motor. This servo is able to take in 6 volts and deliver 30.6 oz-in. of maximum torque at 0.14 sec/60° A standard 3-pin power and control cable is attached and all hardware listed below is included. Includes: 1x SM-S3317S Full Rotation Servo 1x Single Arm Horn 1x Double Arm Horn 1x Four Point Horn 4x Rubber Grommets 4x 2x15mm Phillips Screw 4x Brass Eyelets Features: Voltage: 4.8-6.0 Volts Torque:...

Here is a powerful, low-cost, reliable servo for all your mechatronic needs. This servo is able to take in 6 volts and deliver 83.47 oz-in. of maximum torque at 0.16 sec/60° This is a tough little...

Here is a powerful, low-cost, reliable servo for all your mechatronic needs. This servo is able to take in 6 volts and deliver 83.47 oz-in. of maximum torque at 0.16 sec/60° This is a tough little servo with a standard 3 pin power and control cable, and all hardware listed below. Replaces:ROB-9064 Includes: 1x FS5106B High Torque Servo 1x Double Arm Horn 1x Circle Horn 1x Four Point Horn 1x Six Point Horn 2x 3x10mm Phillips Screw 4x 2x13mm Mounting Phillips Screw 4x Rubber Grommets 4x Brass...

Here, for all your mechatronic needs, is a simple, high quality continuous rotation servo motor. This servo is able to take in 6 volts and deliver 66.7 oz-in. of maximum torque at 70 r/min. A...

Here, for all your mechatronic needs, is a simple, high quality continuous rotation servo motor. This servo is able to take in 6 volts and deliver 66.7 oz-in. of maximum torque at 70 r/min. A standard 3-pin power and control cable is attached and all hardware listed below is included. Includes: 1x SM-S4303R High Torque Continuous Rotation Servo 1x Mounting Screw 1x Four Point Horn 1x Six Point Horn 2x Double Arm Horn (1x Large, 1x Medium) 2x Circle Horn (1x Large, 1x Medium) 4x Rubber...

"Here is a simple, low-cost, high quality servo for all your mechatronic needs. This servo is able to take in 6 volts and deliver 44.4 oz-in. of maximum torque at 0.18 sec/60° This is a small...

"Here is a simple, low-cost, high quality servo for all your mechatronic needs. This servo is able to take in 6 volts and deliver 44.4 oz-in. of maximum torque at 0.18 sec/60° This is a small servo with a standard 3 pin power and control cable (red = power, brown = ground, and yellow = data), and all hardware listed below. Features: Voltage: 4.8-6.0 Volts Torque: 38.8/44.4 oz-in. (4.8/6.0V) Speed: 0.20/0.18 sec/60° (4.8/6.0V) Rotation: 180° Dual Ball Bearing Metal Gears...

Shining 3D Einscan Industrial Pack Capture high-accuracy and high-resolution 3D data of small to medium objects.For EinScan Pro 2X 2020 & EinScan Pro HD Tripod & Turntable Industrial Pack enables...

Shining 3D Einscan Industrial Pack Capture high-accuracy and high-resolution 3D data of small to medium objects.For EinScan Pro 2X 2020 & EinScan Pro HD Tripod & Turntable Industrial Pack enables Fixed Scan with or without turntable to achieve high accuracy and details of scanned 3D data, allowing turntable alignment and coded target alignment for various possibilities of scanning small to medium size. Fixed Scan with Turntable For completing a 360-degree automatic scan in few...

Shining 3D Einscan Marker DotsPack of  Einscan Marker dots Compatible with EinScan SP, EinScan Pro 2X+, Pro HD, HX

Shining 3D Einscan Marker DotsPack of  Einscan Marker dots Compatible with EinScan SP, EinScan Pro 2X+, Pro HD, HX

Shining 3D Einscan TP (Colour Texture Pack) Texture camera captures full-color texture for 3D model. For EinScan Pro Series including EinScan Pro 2X 2020& EinScan Pro HD By attaching the Color Pack,...

Shining 3D Einscan TP (Colour Texture Pack) Texture camera captures full-color texture for 3D model. For EinScan Pro Series including EinScan Pro 2X 2020& EinScan Pro HD By attaching the Color Pack, the EinScan-Pro series can capture full-color texture, and enables texture alignment for more possibilities of scanning. Color Pack activates texture tracking in handheld Rapid Mode to align scans without using markers. ...

Silicone Nozzle Cover For all Ultimaker parts reach out to the team at MindKits for some help. Contact us via Online Chat or Email

Silicone Nozzle Cover For all Ultimaker parts reach out to the team at MindKits for some help. Contact us via Online Chat or Email

Silicone Nozzle Cover for the Ultimaker S5 For all Ultimaker parts reach out to the team at MindKits for some help. Contact us via Online Chat or Email

Silicone Nozzle Cover for the Ultimaker S5 For all Ultimaker parts reach out to the team at MindKits for some help. Contact us via Online Chat or Email

These skate wheel adaptors have a diameter of 1”, a width of 0.32”, and utilize the 0.77” hub pattern. These adaptors allow you to attach the 2.975” or 4.90” skate wheels to ¼” drive shafts....

These skate wheel adaptors have a diameter of 1”, a width of 0.32”, and utilize the 0.77” hub pattern. These adaptors allow you to attach the 2.975” or 4.90” skate wheels to ¼” drive shafts. Actobotics is a robotics building system based around extruded aluminum channels, gears, precision shafts, and ball bearings. Thanks to the two standardized hole patterns, nearly all Actobotics components can be intuitively connected together. The wide range of components makes building complex...

SM5100B Evaluation Board Description: This is an evaluation board for the SM5100B GSM/GPRS module; everything you need to get started with the cellular module is included on this board. With FTDI's...

SM5100B Evaluation Board Description: This is an evaluation board for the SM5100B GSM/GPRS module; everything you need to get started with the cellular module is included on this board. With FTDI's FT232RL connected up to UART0 of the SM5100B you can send AT commands from a PC terminal straight to the module. This board comes as shown in the picture with the 60-pin SM5100B mating connector, SIM card socket, SPX29302 3.8VDC high-current voltage regulator, FT232RL USB-to-UART,...

One (1) MDF Wasteboard for Snapmaker 2.0 A250. Each Snapmaker model comes with one MDF wasteboard as a CNC platform. This is a replacement wasteboard for your Snapmaker 2.0. The relatively soft...

One (1) MDF Wasteboard for Snapmaker 2.0 A250. Each Snapmaker model comes with one MDF wasteboard as a CNC platform. This is a replacement wasteboard for your Snapmaker 2.0. The relatively soft MDF provides a surface that allows for easy through-cutting operations without having to worry about damaging the tools or your Snapmaker.

One (1) MDF Wasteboard for Snapmaker 2.0 A350. Each Snapmaker model comes with one MDF wasteboard as a CNC platform. This is a replacement wasteboard for your Snapmaker 2.0. The relatively soft...

One (1) MDF Wasteboard for Snapmaker 2.0 A350. Each Snapmaker model comes with one MDF wasteboard as a CNC platform. This is a replacement wasteboard for your Snapmaker 2.0. The relatively soft MDF provides a surface that allows for easy through-cutting operations without having to worry about damaging the tools or your Snapmaker.

Straight Groove V-bits for Snapmaker 2.0 (3 Bits) The straight groove v-bit is ideal for rotary projects and detailed oriented works. Its special size makes it stand out in most rotary carving tasks...

Straight Groove V-bits for Snapmaker 2.0 (3 Bits) The straight groove v-bit is ideal for rotary projects and detailed oriented works. Its special size makes it stand out in most rotary carving tasks and could be customized through Snapmaker Luban (4-axis CNC functionality) to achieve optimal carving results. Straight Groove V-bits UF20 tungsten steel alloy with high hardness and wear resistance, not only is it suitable for epoxy tooling material, but it is also compatible with a dozen...

An air purifier made specially for Snapmaker 2.0 product series. It's able to remove PM and VOCs released to the air during 3D printing and laser engraving process, ensuring the safety of its users....

An air purifier made specially for Snapmaker 2.0 product series. It's able to remove PM and VOCs released to the air during 3D printing and laser engraving process, ensuring the safety of its users. The Air Purifier must be used in combination with Snapmaker 2.0 Enclosure. Dimensions: 240x240x420mm Hose: 72x2000mm Weight: 8.5kg(excluding the hose and hose clamps) Rated Power: 120W Filtration Efficiency (0.3–0.5 μm): 95.9%

This is your basic spool of lead free solder with a water soluble resin core. 0.031" gauge and 100 grams. This is a good spool for more advanced users that should last 6-12 months depending on how...

This is your basic spool of lead free solder with a water soluble resin core. 0.031" gauge and 100 grams. This is a good spool for more advanced users that should last 6-12 months depending on how often you solder. If you are just beginning to solder, we recommend you order the leaded solder. Lead-free solder is a bit harder to use (does not flow as well). Mix: 99.3% Sn / 0.7% Cu Documents: MSDS ...

This is a replacement soldering tip for the Weller WLC100 soldering iron. It is a standard type of soldering tip, measuring 0.062" (1.58mm) wide. Replacing the tip is a breeze --- simply unscrew the...

This is a replacement soldering tip for the Weller WLC100 soldering iron. It is a standard type of soldering tip, measuring 0.062" (1.58mm) wide. Replacing the tip is a breeze --- simply unscrew the currently attached tip with a flat-head screwdriver, slip the replacement tip in, and screw it into place. The standard Weller tip has been pre-tinned with a lead-free alloy.

Description This breadboard have 2x 60 rows of interconnected pins (5 per row) and two long rows on both sides - 700 pins in total. Its dimension is 17.6*4.6*8.3cm. Plesae note that it has no...

Description This breadboard have 2x 60 rows of interconnected pins (5 per row) and two long rows on both sides - 700 pins in total. Its dimension is 17.6*4.6*8.3cm. Plesae note that it has no self-adhesive backing and no interlocking part.Features700 Tie PointDimensions: 17.6 * 4.6 * 8.3cm ...

Sovol SV08 Replacement Touch Screen 5-inch IPS capacitive touchscreen with 800×480 resolution, offering vivid colors and wide viewing angles. Preinstalled Klipper firmware speeds up printer printing...

Sovol SV08 Replacement Touch Screen 5-inch IPS capacitive touchscreen with 800×480 resolution, offering vivid colors and wide viewing angles. Preinstalled Klipper firmware speeds up printer printing while maintaining print quality. Easy installation via HDMI, though some custom fitting may be needed for the SV08 frame. ...

Overview The Bambu Cool Sheet is a sheet with an adhesive side for replacing the sheet on your Cool Plate. Compatibility X1 Series and P1 Series Note The Bambu Cool sheet is easy to replace and...

Overview The Bambu Cool Sheet is a sheet with an adhesive side for replacing the sheet on your Cool Plate. Compatibility X1 Series and P1 Series Note The Bambu Cool sheet is easy to replace and install. After tearing off the original sheet, please use alcohol to wipe the surface clean. Make sure the surface stays dry while applying a new sheet.You can use an anhydrous ethanol solution or isopropanol solution with a concentration of over 90% to wipe the plate.You can also use detergent and...

"4-digit 7-segment displays are really neat little devices, it’s a shame that they can be so cumbersome to control. Well we’ve solved that problem by making them a little bit...

"4-digit 7-segment displays are really neat little devices, it’s a shame that they can be so cumbersome to control. Well we’ve solved that problem by making them a little bit “smarter.” The SparkFun 7-Segment Serial Display combines a classic 4-digit 7-segment display and an ATMega328 microcontroller allowing you to control every segment individually using only a few serial lines. The Serial 7-Segment Display can be controlled in one of three ways: Serial TTL...

"This is a breakout board for the Bosch BMP180 high-precision, low-power digital barometer. The BMP180 offers a pressure measuring range of 300 to 1100 hPa with an accuracy down to 0.02 hPa in...

"This is a breakout board for the Bosch BMP180 high-precision, low-power digital barometer. The BMP180 offers a pressure measuring range of 300 to 1100 hPa with an accuracy down to 0.02 hPa in advanced resolution mode. It’s based on piezo-resistive technology for high accuracy, ruggedness and long term stability. These come factory-calibrated, with the calibration coefficients already stored in ROM. What makes this sensor great is that it is nearly identical to its former rev, the...

"This is a breakout for the BC127 Bluetooth Module. The BC127 is a highly flexible, low power, small form factor Bluetooth Version 4.0 Certified Audio module. This is an ideal module for developers...

"This is a breakout for the BC127 Bluetooth Module. The BC127 is a highly flexible, low power, small form factor Bluetooth Version 4.0 Certified Audio module. This is an ideal module for developers who want to quickly and cost effectively integrate Bluetooth functionality into their products. The BC127 Breakout board provides basic access to all the pins on the BC127 module, along with a six-pin serial header with the same pinout as the FTDI Basic boards, allowing it to connect to boards like...

The Bluetooth Mate is very similar to our BlueSMiRF modem, but it is designed specifically to be used with our Arduino Pros and LilyPad Arduinos. These modems work as a serial (RX/TX) pipe, and are...

The Bluetooth Mate is very similar to our BlueSMiRF modem, but it is designed specifically to be used with our Arduino Pros and LilyPad Arduinos. These modems work as a serial (RX/TX) pipe, and are a great wireless replacement for serial cables. Any serial stream from 2400 to 115200bps can be passed seamlessly from your computer to your target. Bluetooth Mate has the same pin out as the FTDI Basic, and is meant to plug directly into an Arduino Pro, Pro Mini, or LilyPad Mainboard. Because we've...

The BlueSMiRF is the latest Bluetooth****wireless serial cable replacement from SparkFun Electronics! These modems work as a serial (RX/TX) pipe. Any serial stream from 2400 to 115200bps can be...

The BlueSMiRF is the latest Bluetooth****wireless serial cable replacement from SparkFun Electronics! These modems work as a serial (RX/TX) pipe. Any serial stream from 2400 to 115200bps can be passed seamlessly from your computer to your target. We've tested these units successfully over open air at 350ft (106m)! The latest version of this board also breaks out PIO4. Note: The remote unit can be powered from 3.3V up to 6V for easy battery attachment. All signal pins on the remote unit are...

Blynk is an easy to use app builder that allows users to add a variety of buttons, sliders, graphical displays and even RGB controllers to their phone. The SparkFun Blynk Board is specially designed...

Blynk is an easy to use app builder that allows users to add a variety of buttons, sliders, graphical displays and even RGB controllers to their phone. The SparkFun Blynk Board is specially designed to work with the ‘widgets’ within the Blynk mobile app to create your next IoT project. Monitor local weather conditions, control LEDs from your phone, even send a tweet when it’s time to water your plants! Every Blynk Board comes fully programmed and also includes a Blynk subscription code card...

"The MG2639 SparkFun Cellular Shield is a perfect addition to any Arduino project that requires connectivity when there’s no WiFi or Ethernet access nearby. The ZTE MG2639 module, which this...

"The MG2639 SparkFun Cellular Shield is a perfect addition to any Arduino project that requires connectivity when there’s no WiFi or Ethernet access nearby. The ZTE MG2639 module, which this shield is built around, supports SMS, TCP, UDP, and can even be used to make or receive phone calls! That means you can send and receive text messages, or use it to remotely connect your Arduino to the Internet. To top it off, it has an integrated GPS receiver, to help it from getting lost. All the...

You've got the wrong USB cable. It doesn't matter which one you have, it's the wrong one. But what if you could have the right one? What if you could have the right one every time? Enter: The...

You've got the wrong USB cable. It doesn't matter which one you have, it's the wrong one. But what if you could have the right one? What if you could have the right one every time? Enter: The Cerberus. The Cerberus is a three-headed cable-beast that will ensure that you're never stuck looking for a USB cable that fits your device. At one end of the Cerberus you have the standard A-type connector, which you can plug into your computer or USB power supply; At the other end are three common USB...

Here is a real time clock based on the DS3234 Real Time Clock IC. The DS3234 is a low-cost, extremely accurate SPI bus real-time clock with an integrated temperature-compensated crystal oscillator...

Here is a real time clock based on the DS3234 Real Time Clock IC. The DS3234 is a low-cost, extremely accurate SPI bus real-time clock with an integrated temperature-compensated crystal oscillator and crystal. The RTC maintains seconds, minutes, hours, day, date, month, and year information. The date at the end of the month is automatically adjusted for months with fewer than 31 days, including corrections of leap year. The clock operates in either the 24-hour or 12-hour format with AM/PM...

This is the Add-On kit for the SparkFun Digital Sandbox (DS) learning platform. With this add-on you will be able to perform the final three circuit experiments found in the DS Guide book which...

This is the Add-On kit for the SparkFun Digital Sandbox (DS) learning platform. With this add-on you will be able to perform the final three circuit experiments found in the DS Guide book which include making an electric musical instrument, telling a motor to spin as fast as you want, and controlling a servo. This is the perfect kit if you've completed everything to do with the Digital Sandbox but are looking for more! Note: If you are looking for the first 13 experiments they can be found...

The TMP102 is an easy-to-use digital temperature sensor from Texas Instruments. The TMP102 breakout allows you to easily incorporate the digital temperature sensor into your project. While some...

The TMP102 is an easy-to-use digital temperature sensor from Texas Instruments. The TMP102 breakout allows you to easily incorporate the digital temperature sensor into your project. While some temperature sensors use an analog voltage to represent the temperature, the TMP102 uses the I2C bus of the Arduino to communicate the temperature. Needless to say, this is a very handy sensor that doesn't require much setup. The TMP102 is capable of reading temperatures to a resolution of 0.0625°C, and...

Edge computing is here! You've probably heard of this latest entry to the long lineage of tech buzzwords like "IoT," "LoRa," and "cloud" before it, but what is “the edge” and why does it matter? The...

Edge computing is here! You've probably heard of this latest entry to the long lineage of tech buzzwords like "IoT," "LoRa," and "cloud" before it, but what is “the edge” and why does it matter? The cloud is impressively powerful but all-the-time connection requires power and connectivity that may not be available. Edge computing handles discrete tasks such as determining if someone said "yes" and responds accordingly. The audio analysis is done at the edge rather than on the web. This...

This small breakout board couples an Electret microphone (100Hz--10kHz) with a 60x mic preamplifier to amplify the sounds of voice, claps, door knocks or any sounds loud enough to be picked up by a...

This small breakout board couples an Electret microphone (100Hz--10kHz) with a 60x mic preamplifier to amplify the sounds of voice, claps, door knocks or any sounds loud enough to be picked up by a microcontroller’s analog-to-digital converter. Each breakout comes fully assembled and works from 2.7V up to 5.5V. The Electret Mic Breakout translates amplitude (not volume) by capturing sound waves between two conducting plates (one a vibrating diaphragm and the other fixed) in the microphone and...

"If you aren’t familiar with the Electric Imp, it essentially provides an easy, integrated way to connect almost any hardware device both to other devices and to internet services. The...

"If you aren’t familiar with the Electric Imp, it essentially provides an easy, integrated way to connect almost any hardware device both to other devices and to internet services. The SparkFun Electric Imp Breakout Board allows you to explore the capabilities of the Imp by providing standard 0.1" headers to solder to as well as the necessary CryptAuthEE IC to identify your prototype to the Imp Cloud service! This is just the development board, so you’ll need to buy the Imp...

The SparkFun ESP8266 Thing is a breakout and development board for the ESP8266 WiFi SoC – a leading platform for Internet of Things (IoT) or WiFi-related projects. The Thing is low-cost and easy to...

The SparkFun ESP8266 Thing is a breakout and development board for the ESP8266 WiFi SoC – a leading platform for Internet of Things (IoT) or WiFi-related projects. The Thing is low-cost and easy to use, and Arduino IDE integration can be achieved in just a few steps. We've made the ESP8266 easy to use by breaking out all of the module’s pins, adding a LiPo charger, power supply, and all of the other supporting circuitry it requires. Why the name? We lovingly call it the “Thing” due to it being...

This is the SparkFun ESP8266 Thing Dev Board – a development board that has been solely designed around the ESP8266, with an integrated FTDI USB-to-Serial chip. The ESP8266 is a cost-effective, and...

This is the SparkFun ESP8266 Thing Dev Board – a development board that has been solely designed around the ESP8266, with an integrated FTDI USB-to-Serial chip. The ESP8266 is a cost-effective, and very capable WiFi-enabled microcontroller. Like any microcontroller, it can be programmed to blink LEDs, trigger relays, monitor sensors, or automate coffee makers, and with an integrated WiFi controller, the ESP8266 is a one-stop shop for almost any Internet-connected project. To top it all off,...

This is a simple breakout board for the MQ - 3, MQ - 4, MQ - 6, MQ - 7, and MQ - 8 gas sensors. With the Gas Sensor Breakout you will be able to utilize each oversized, oddly spaced pins featured on...

This is a simple breakout board for the MQ - 3, MQ - 4, MQ - 6, MQ - 7, and MQ - 8 gas sensors. With the Gas Sensor Breakout you will be able to utilize each oversized, oddly spaced pins featured on every MQ gas sensor product. This is an extremely handy and economical board to have around when detecting multiple types of gases. All you need is the VCC at 5V, GND, and a resistor to an ADC, that is it! Note: This is just the PCB. The appropriate sensors are listed below in the Recommended...

This is the serial backpack for graphic LCDs. The SparkFun Graphic LCD Serial Backpack interfaces to either our 160x128 pixel “Huge” Graphic LCD, or the smaller 128x64 pixel display, and provides a...

This is the serial backpack for graphic LCDs. The SparkFun Graphic LCD Serial Backpack interfaces to either our 160x128 pixel “Huge” Graphic LCD, or the smaller 128x64 pixel display, and provides a simple serial interface to a full range of controls. This backpack will allow you to write text, draw lines, circles and boxes, set or reset individual pixels, and erase specific blocks of the display. The backlight and baud rate can also be controlled via serial communication. There's also a...

"The SparkFun H2OhNo! is a water sensor alarm kit that you build yourself. When water is detected across the sense pins an alarm goes off and an LED starts blinking. If you’ve ever had a water...

"The SparkFun H2OhNo! is a water sensor alarm kit that you build yourself. When water is detected across the sense pins an alarm goes off and an LED starts blinking. If you’ve ever had a water heater explode or tried to create submersible electronics you know how important it is to be able to detect when water is around! Underneath the default function of H2OhNo! is a small but powerful development board for the ATtiny85 microcontroller. The board includes a buzzer, LED, a coin cell...

It's not the heat but the humidity that gets you, at least that's what they say. Really, both are important, what you need is a sensor that combines humidity and temperature readings. How about this...

It's not the heat but the humidity that gets you, at least that's what they say. Really, both are important, what you need is a sensor that combines humidity and temperature readings. How about this Honeywell HumidIcon Digital Humidity/Temperature Sensor? The HIH6130 is a digital output-type relative humidity (RH) and temperature sensor combined in the same package. This allows the RH measurement to be temperature compensated and provides a second, standalone temperature sensor output. This...

This is a breakout board for Honeywell's HIH-4030 humidity sensor. The HIH-4030 measures relative humidity (%RH) and delivers it as an analog output voltage. You can connect the output of the sensor...

This is a breakout board for Honeywell's HIH-4030 humidity sensor. The HIH-4030 measures relative humidity (%RH) and delivers it as an analog output voltage. You can connect the output of the sensor directly to an ADC on a microcontroller; and, thanks to the sensor's near linear voltage output, the data is very easy to process. Voltage applied to the supply pins should be within 4-5.8VDC, and optimally at 5V. The sensor will typically only consume about 200μA. This product comes as shown in...

"The MicroView is an amazingly small, Arduino compatible, OLED display module that everyone seems to be clamoring for. The SparkFun Inventor’s Kit for MicroView provides you not only with the...

"The MicroView is an amazingly small, Arduino compatible, OLED display module that everyone seems to be clamoring for. The SparkFun Inventor’s Kit for MicroView provides you not only with the MicroView module and its programmer but everything you need to hook up and experiment with multiple electronic circuits! With the MicroView SIK you will be able to complete 11 circuits that will teach you how to write code, read sensors, drive motors, and more while still being able to display...

"The SparkFun Inventor’s Kit for Photon is a great way to get started in the fresh IoT world and WiFi development. The SparkFun Inventor’s Kit for Photon provides you not only with the...

"The SparkFun Inventor’s Kit for Photon is a great way to get started in the fresh IoT world and WiFi development. The SparkFun Inventor’s Kit for Photon provides you not only with the Photon RedBoard but everything you need to hook up and experiment with multiple electronic circuits! With the Photon SIK you will be able to complete circuits that will teach you how to read sensors, drive motors, and more. The SparkFun Inventor’s Kit for Photon is the latest and greatest in...

The SparkFun Inventor’s Kit for RedBot is a great way to get started with two motor robotics and sensor integration using the Arduino programming language. The SIK for RedBot includes everything you...

The SparkFun Inventor’s Kit for RedBot is a great way to get started with two motor robotics and sensor integration using the Arduino programming language. The SIK for RedBot includes everything you need to complete nine circuits that will teach you how to drive your RedBot, have it follow lines, control it remotely, and more. This kit doesn't require previous programming or electronics experience but it is recommended that you possess an understanding of or desire to learn about robotics. The...

The SparkFun Joystick Shield Kit contains all the parts you need to enable your Arduino with a joystick! The shield sits on top of your Arduino and turns it into a simple controller. Five momentary...

The SparkFun Joystick Shield Kit contains all the parts you need to enable your Arduino with a joystick! The shield sits on top of your Arduino and turns it into a simple controller. Five momentary push buttons (4+ joystick select button) and a two-axis thumb joystick gives your Arduino functionality on the level of old Nintendo controllers. Soldering is required, but it's relatively easy and requires minimal tools. We even have a step by step guide! The momentary push buttons are connected to...

"This is the SparkFun LED Starter Kit, an ultimate assortment of LEDs packed into a single red box! Now, this isn’t a box filled with only one type of LED, oh no. Inside each kit you will find...

"This is the SparkFun LED Starter Kit, an ultimate assortment of LEDs packed into a single red box! Now, this isn’t a box filled with only one type of LED, oh no. Inside each kit you will find over 70 multi-colored and multi-functional LEDs and even more resistors to help hook everything up. All colors of the spectrum, super-bright and diffused, 3mm to 10mm, you will find plenty of options suited for almost any situation in the SparkFun LED Starter Kit. Includes: 1x LED Mixed Bag -...

There are a couple must-have boards that every engineer and hobbyist should have on their desk, and this PCA9306 dual, bidirectional voltage-level translator breakout is one of them! Because...

There are a couple must-have boards that every engineer and hobbyist should have on their desk, and this PCA9306 dual, bidirectional voltage-level translator breakout is one of them! Because different parts sometimes use different voltage levels to communicate, voltage level translators can be the key to making different parts play nice. The PCA9306 is a dual bidirectional I2C-bus and SMBus voltage-level translator that's operational on the low side from 1.2V to 3.3V and on the high side from...

The SparkFun Line Follower Array is a long board consisting of eight IR sensors that have been configured to read as digital bits! We have designed the SparkFun Line Follower Arrays to follow a dark...

The SparkFun Line Follower Array is a long board consisting of eight IR sensors that have been configured to read as digital bits! We have designed the SparkFun Line Follower Arrays to follow a dark line of about ¾ inch width or smaller (spray paint or electrical tape) on a light background. Each array features visible LEDs that point upward when the board is attached (properly) so you can see what the robot sees, brightness control right on the board, and an I2C interface for reading and...

If you need to charge LiPo batteries, this simple charger will do just that. It is designed to charge single-cell Li-Ion or Li-Polymer batteries. Check the datasheet below to see if it will work...

If you need to charge LiPo batteries, this simple charger will do just that. It is designed to charge single-cell Li-Ion or Li-Polymer batteries. Check the datasheet below to see if it will work with your battery. The board incorporates a charging circuit, status LED, connector for your battery (JST-type used in the batteries we carry), and a mini-USB connector. However, we do not recommend this charger with a 110mAh battery. Note: This version uses a mini-USB cable. We also have this charger...

The SparkFun Micro OLED Breakout Board breaks out a small monochrome, blue-on-black OLED. It’s "micro", but it still packs a punch – the OLED display is crisp, and you can fit a deceivingly large...

The SparkFun Micro OLED Breakout Board breaks out a small monochrome, blue-on-black OLED. It’s "micro", but it still packs a punch – the OLED display is crisp, and you can fit a deceivingly large amount of graphics on there. This breakout is perfect for adding graphics to your next Arduino project, displaying diagnostic information without resorting to serial output, and teaching a little game theory while creating a fun, Arduino-based video game. Most important of all, though, is the Micro...

The SparkFun micro:bit Breakout is a board that connects to the BBC micro:bit and expands the capabilities of the development platform by providing access to more pins and allowing for connections...

The SparkFun micro:bit Breakout is a board that connects to the BBC micro:bit and expands the capabilities of the development platform by providing access to more pins and allowing for connections to the I2C and SPI buses. This breakout board for the micro:bit’s edge connector allows intermediate and advanced users to connect the micro:bit to breadboards and other sensors, motors, LEDs and more! The micro:bit on its own has three digital/analog input/output rings available for you to use...

Running out of memory space in your Arduino project? The SparkFun microSD Shield equips your Arduino with mass-storage capability, so you can use it for data-logging or other related projects....

Running out of memory space in your Arduino project? The SparkFun microSD Shield equips your Arduino with mass-storage capability, so you can use it for data-logging or other related projects. Communication with microSD cards is achieved over an SPI interface. The SCK, DI, and DO pins of the microSD socket are broken out to the ATmega168/328's standard SPI pins (digital 11-13), while the CS pin is broken out to Arduino's D8 pin. If you decide to use one of the many open source FAT libraries...

This is a unique board recommended by a SparkFun customer. When playing with microSD, you sometimes need to view what the SPI traffic is doing, whether for hacking or debugging. The SparkFun microSD...

This is a unique board recommended by a SparkFun customer. When playing with microSD, you sometimes need to view what the SPI traffic is doing, whether for hacking or debugging. The SparkFun microSD Sniffer allows you to hook up an external device, such as a logic analyzer or microcontroller, to view what signals are being passed back and forth. Insert one side into a regular uSD socket and a uSD card into the on-board socket, simple as that. All necessary pins are broken out to an 8-pin 0.1"...

The MicroView is the first chip-sized Arduino compatible module that lets you see what your Arduino is thinking using a built-in OLED display. With the on-board 64x48 pixel OLED, you can use the...

The MicroView is the first chip-sized Arduino compatible module that lets you see what your Arduino is thinking using a built-in OLED display. With the on-board 64x48 pixel OLED, you can use the MicroView to display sensor data, emails, pin status, and more. It also fits nicely into a breadboard to make prototyping easy. The MicroView also has a full-featured Arduino library to make programming the module easy. In the heart of MicroView there is ATMEL’s ATmega328P, 5V & 3.3V LDO and a 64x48...

The MicroView is the first chip-sized Arduino compatible module that lets you see what your Arduino is thinking using a built-in OLED display. This USB programmer connects directly to the MicroView...

The MicroView is the first chip-sized Arduino compatible module that lets you see what your Arduino is thinking using a built-in OLED display. This USB programmer connects directly to the MicroView and lets you not only program the module, but use it to interface with your computer, Rapsberry Pi, or other USB device. The programmer has both male and female headers which allow it to be plugged into a MicroView module and a breadboard at the same time, making prototyping quick and easy. If you...

This is just your basic reversible screwdriver - pocket sized! Both flat and phillips heads available. Comes with pin clip and snazzy SparkFun logo.

This is just your basic reversible screwdriver - pocket sized! Both flat and phillips heads available. Comes with pin clip and snazzy SparkFun logo.

The TB6612FNG Motor Driver can control up to two DC motors at a constant current of 1.2A (3.2A peak). Two input signals (IN1 and IN2) can be used to control the motor in one of four function modes:...

The TB6612FNG Motor Driver can control up to two DC motors at a constant current of 1.2A (3.2A peak). Two input signals (IN1 and IN2) can be used to control the motor in one of four function modes: CW, CCW, short-brake and stop. The two motor outputs (A and B) can be separately controlled, and the speed of each motor is controlled via a PWM input signal with a frequency up to 100kHz. The STBY pin should be pulled high to take the motor out of standby mode. Logic supply voltage (VCC) can be in...

The TB6612FNG Motor Driver can control up to two DC motors at a constant current of 1.2A (3.2A peak). Two input signals (IN1 and IN2) can be used to control the motor in one of four function modes:...

The TB6612FNG Motor Driver can control up to two DC motors at a constant current of 1.2A (3.2A peak). Two input signals (IN1 and IN2) can be used to control the motor in one of four function modes: CW, CCW, short-brake and stop. The two motor outputs (A and B) can be separately controlled, and the speed of each motor is controlled via a PWM input signal with a frequency up to 100kHz. The STBY pin should be pulled high to take the motor out of standby mode. Due to popular demand, this version...

This is a simple 5V Op Amp breakout board, set up as a 2-stage amplifier with a gain of 100 (gain of 10 for each stage). The on-board trim pot sets the signal level between the stages, not the...

This is a simple 5V Op Amp breakout board, set up as a 2-stage amplifier with a gain of 100 (gain of 10 for each stage). The on-board trim pot sets the signal level between the stages, not the feedback path. The bandwidth is set to 15.9kHz by a pair of feedback capacitors, or over 100kHz with the caps removed. The LMV358 opamp can source up to 160mA and works well as a low impedance driver/buffer. Documents: Schematic Eagle Files Introduction to Op Amps with LTSpice Datasheet (LMV358) GitHub...

The SparkFun OpenLog is an open source data logger that works over a simple serial connection and supports microSD cards up to 32GB. The OpenLog can store or "log" huge amounts of serial data and...

The SparkFun OpenLog is an open source data logger that works over a simple serial connection and supports microSD cards up to 32GB. The OpenLog can store or "log" huge amounts of serial data and act as a black box of sorts to store all the serial data that your project generates, for scientific or debugging purposes. The SparkFun OpenLog uses an ATmega328 running at 16MHz thanks to the onboard resonator. The OpenLog draws approximately 2-3mA in idle (nothing to record) mode. During a full...

A simple breakout PCB for the GP1A57HR photo interrupter (also known as a photogate, photodiode, or phototransistor). This PCB has three connections for PWR, GND, and Signal. When the gate is clear,...

A simple breakout PCB for the GP1A57HR photo interrupter (also known as a photogate, photodiode, or phototransistor). This PCB has three connections for PWR, GND, and Signal. When the gate is clear, SIG will be high (>4.9V). When the gate is blocked by a finger, writing utensil, food pellet, or anything else - SIG will go low ( Assembled picture is for reference only, board comes bare; photo interrupter and the 220Ω (330Ω, works as well) current limiting resistor are listed below. Documents:...

This is the SparkFun Pi Wedge, a small board that connects to the 40-pin GPIO connector on the Raspberry Pi and breaks the pins out to breadboard-friendly arrangement and spacing, and even adds a...

This is the SparkFun Pi Wedge, a small board that connects to the 40-pin GPIO connector on the Raspberry Pi and breaks the pins out to breadboard-friendly arrangement and spacing, and even adds a couple of decoupling capacitors on the power supply lines. The "Wedge" also makes the initial bring-up process easier - you can plug an FTDI Basic module into the built-in serial port. Each version of this Pi Wedge comes preassembled and can be inserted into the RPi's GPIO port that allows you to...

This shield allows you to use a computer power supply (or other power source) to use your Arduino to switch high current. With RFP30N06LE MOSFETS, you can easily control a lot of current directly...

This shield allows you to use a computer power supply (or other power source) to use your Arduino to switch high current. With RFP30N06LE MOSFETS, you can easily control a lot of current directly from your Arduino. The board provides 6 PWM outputs via screw terminals. Check the datasheet for the MOSFET below for full specifications on how much current this board can handle.This board is a very easy way to start using MOSFETS for your next high current project. A protection diode has been added...

The SparkFun Qwiic Shield for Teensy provides you with a quick and easy way to enter into SparkFun's Qwiic ecosystem with your Teensy boards. This shield is sized to work with the footprint of...

The SparkFun Qwiic Shield for Teensy provides you with a quick and easy way to enter into SparkFun's Qwiic ecosystem with your Teensy boards. This shield is sized to work with the footprint of Teensy 4.0, Teensy 3.2, and Teensy LC. This shield connects the I2C bus (GND, 3.3V, SDA, and SCL) on your Teensy to four SparkFun Qwiic connectors (two horizontally and two vertically mounted). The Qwiic ecosystem allows for easy daisy chaining so, as long as your devices are on different addresses, you...

The SparkFun Extended Qwiic Shield for Teensy provides you with a quick and easy way to enter into SparkFun's Qwiic ecosystem with your Teensy boards. This shield is sized to work with the footprint...

The SparkFun Extended Qwiic Shield for Teensy provides you with a quick and easy way to enter into SparkFun's Qwiic ecosystem with your Teensy boards. This shield is sized to work with the footprint of Teensy 4.1, Teensy 3.6, and Teensy 3.5. This shield connects the I2C bus (GND, 3.3V, SDA, and SCL) on your Teensy to four SparkFun Qwiic connectors (two horizontally and two vertically mounted). The Qwiic ecosystem allows for easy daisy chaining so, as long as your devices are on different...

The SparkFun QwiicBus EndPoint is the fastest and easiest way to extend the range of your I2C communication bus. The breakout uses NXP’s PCA9615 IC, which converts the two default I2C signals into...

The SparkFun QwiicBus EndPoint is the fastest and easiest way to extend the range of your I2C communication bus. The breakout uses NXP’s PCA9615 IC, which converts the two default I2C signals into four differential signals, two for SCL and two for SDA. The differential signals are sent over an Ethernet cable, which attaches to the breakout through the on-board RJ-45 connectors. The differential signaling allows the I2C signals to reach distances of up to 100ft. while still maintaining their...

"Welcome the RedBot Basic Kit, a robotic development platform capable of teaching two motor robotics and sensor integration! This kit comes with our RedBot Mainboard, the Shadow Chassis, a handful...

"Welcome the RedBot Basic Kit, a robotic development platform capable of teaching two motor robotics and sensor integration! This kit comes with our RedBot Mainboard, the Shadow Chassis, a handful of sensors, and everything required to get it moving. The RedBot Mainboard is a modular robotic development platform that works with the Arduino IDE. The RedBot is a motor driver and Ardiuno combination with various headers and connections, eliminating the need to stack multiple shields to get...